|
|
Content .. 2512 2513 2514 2515 ..
Control Module References for ECM replacement, setup and programming. DTC P0806 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptor DTC P0806 Clutch Pedal Position (CPP) Sensor Circuit Performance Diagnostic Fault Information Typical Scan Tool Information CPP Sensor Voltage CPP Sensor Percentage Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance CPP Sensor Signal P0807 P0807 P0808 P0806 CPP Sensor 5-Volt Reference P0651, P0807 P0807 P0651, P0808 - CPP Sensor Low Reference - P0808 P0808 - Circuit Short to Ground Open Short to Voltage Operating Conditions: Ignition ON. 0 volts 0 volts 5 volts CPP Sensor Signal 0 volts 0 volts 5 volts CPP Sensor Low Reference - 5 volts - Circuit Short to Ground Open Short to Voltage
2008 Chevrolet Silverado 1500 2008 TRANSMISSION Manual Transmission - Tremec 5-Speed (M96) - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Circuit/System Description The clutch pedal position (CPP) sensor is a three wire sensor, connected to a 5-volt reference Conditions for Running the DTC DTCs P0335, P0336, P0502, P0503, P0607, P0808, or P080A are not set. Conditions for Setting the DTC The CPP sensor is stuck in range. Action Taken When the DTC Sets P0806 is a Type A DTC. Conditions for Clearing the MIL/DTC P0806 is a Type A DTC. Reference Information Schematic Reference PSD SIE TITLE Error: SIE linked to empty Cell ID 168122 Connector End View Reference Component Connector End Views Description and Operation Operating Conditions: Ignition ON. 100% 100% 0-100% CPP Sensor Signal 100% 100% 100% CPP Sensor Low Reference - 0% -
2008 Chevrolet Silverado 1500 2008 TRANSMISSION Manual Transmission - Tremec 5-Speed (M96) - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Manual Transmission Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs DTC Type Reference Powertrain Diagnostic Trouble Code (DTC) Type Definitions Scan Tool Reference Control Module References for scan tool information. Circuit/System Verification 1. Ignition ON, observe the scan tool CPP sensor percent parameter. The percentage should vary from 0% when the clutch pedal is released, to 100% when the clutch pedal is in the 2. Perform the CPP learn procedure. Refer to Clutch Pedal Position Sensor Learn. 3. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Circuit/System Testing 1. Ignition OFF, disconnect the harness connector of the CPP sensor. 2. Ignition ON, observe the scan tool CPP sensor voltage parameter for 0.1-volt. If the voltage is below the specified value, replace the CPP sensor. If the voltage is above the specified value, replace the ECM. Component Testing 1. Ignition OFF, disconnect the harness connector of the CPP sensor. 2. Measure the resistance between the signal terminal B and the low reference terminal A of the CPP sensor. Sweep the CPP sensor through the entire range. The resistance should vary
2008 Chevrolet Silverado 1500 2008 TRANSMISSION Manual Transmission - Tremec 5-Speed (M96) - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
low to high and high to low without any spikes or dropouts. If the resistance is erratic with spikes or dropouts, replace the CPP sensor. Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Clutch Pedal Replacement Control Module References for ECM replacement, setup and programming DTC P0807 OR P0808 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptors DTC P0807 Clutch Pedal Position (CPP) Sensor Circuit Low Voltage DTC P0808 Clutch Pedal Position (CPP) Sensor Circuit High Voltage Diagnostic Fault Information Typical Scan Tool Information CPP Sensor Voltage Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance CPP Sensor Signal P0807 P0807 P0808 P0806 CPP Sensor 5-Volt Reference P0651, P0807 P0807 P0651, P0808 - CPP Sensor Low Reference - P0808 P0808 - Short to Short to
2008 Chevrolet Silverado 1500 2008 TRANSMISSION Manual Transmission - Tremec 5-Speed (M96) - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 2512 2513 2514 2515 ..
|
|
|