|
|
Content .. 1308 1309 1310 1311 ..
If any of the resistance measurements for the individual switches are not within the Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Steering Wheel Control Switch Assembly Replacement Control Module References for BCM replacement, setup, and programming DTC B0835 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptor DTC B0835 00 Cruise Control System Active Indicator Circuit Diagnostic Fault Information Function Switch Minimum Resistance Value Maximum Resistance Value OFF O.L. O.L. ON 6.6k Ohms 7.0k Ohms -/SET 2.1k Ohms 2.5k Ohms +/RES 3.6k Ohms 4.0k Ohms Cancel 1.3k Ohms 1.7k Ohms Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance Cruise Control Indicator 1 2 B0835 00 - 1. Cruise Control Switch Indicator Dimming Inoperative
2008 Chevrolet Silverado 1500 2008 ENGINE Cruise Control - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Circuit/System Description The cruise control switch contains an LED that illuminates to indicate the cruise control system Conditions for Running the DTC The ignition is ON. Conditions for Setting the DTC The BCM detects excessive current in the cruise control indicator dimming signal circuit. The above condition is present for greater than 5 seconds. Action Taken When the DTC Sets The BCM stores DTC B0835 in memory. The cruise control system becomes inoperative. Conditions for Clearing the DTC The DTC becomes history when the conditions for setting the DTC are no longer present. The history DTC clears after 50 malfunction-free warm-up cycles. Reference Information Schematic Reference Cruise Control Schematics Connector End View Reference Component Connector End Views Description and Operation Cruise Control Description and Operation 2. Cruise Control Switch Indicator Inoperative
2008 Chevrolet Silverado 1500 2008 ENGINE Cruise Control - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for scan tool information Circuit/System Verification Ignition ON, observe the cruise control indicator while applying the cruise On/Off switch. The Circuit/System Testing Disable the inflatable restraint steering wheel module when performing this diagnostic. Refer to 1. Ignition OFF, remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement . 2. Disconnect the harness connector at the cruise control switch assembly. 3. Ignition ON, test for 0 volts between the cruise control harness connector terminal 9 and ground. If voltage is present, test the circuit for a short to voltage. 4. If the circuit tests normal, replace the BCM. Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Control Module References for BCM replacement, setup, and programming DTC P0571 CAUTION: Refer to SIR Caution .
2008 Chevrolet Silverado 1500 2008 ENGINE Cruise Control - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptor DTC P0571 00 Cruise Control Brake Switch Circuit Diagnostic Fault Information Circuit/System Description The brake switch signal circuit is a high voltage input to the body control module (BCM), engine Conditions for Running the DTC The ignition is ON. The engine is running. Battery voltage is greater than 11.5 volts. Conditions for Setting the DTC The ECM detects a low voltage signal on the brake switch signal circuit when the serial data Action Taken When the DTC Sets Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance Brake Switch Signal P0571 P0571 - P0571
2008 Chevrolet Silverado 1500 2008 ENGINE Cruise Control - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 1308 1309 1310 1311 ..
|
|
|