Snowmobile Polaris 600 RUSH (2010 year). Manual - part 12

 

  Index      Snowmobiles / ATV     Snowmobile Polaris 600 RUSH - service manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  10  11  12  13   ..

 

 

Snowmobile Polaris 600 RUSH (2010 year). Manual - part 12

 

 

1.46

General Information

9923311 - 2010-2012 PRO-RIDE RUSH/Switchback/RMK Service Manual

© 2011 Polaris Sales Inc.

Measurement Conversion Chart

Piston Wash / Spark Plug Reading

Changing temperature, barometer, altitude, and fuel 
supply are just a few of the factors that can affect the day 
to day performance of your engine. That is why using 
Exhaust Gas Temperatures (EGT) are important for 
maintaining optimum performance. There are two 
methods for helping you determine what the EGTs are for 
your machine. Piston wash and the coloring of your spark 
plug. The piston wash is by far the most valuable tool in 
concluding EGTs, with the spark plug color running a 
distant second. Use the illustrations below to help 
establish the EGTs for your machine.

U

NIT

 

OF

 

M

EASURE

M

ULTIPLIED

 

BY

C

ONVERTS

 

TO

ft-lb

x 12

= in-lb

in-lb

x.0833

= ft-lb

ft-lb

x 1.356

= N-m

in-lb

x.0115

= kg-m

 N-m

x.7376

= ft-lb

kg-m

x 7.233

= ft-lb

kg-m

x 86.796

= in-lb

kg-m

x 10

= N-m

in

x 25.4

= mm

mm

x.03937

= in

in

x 2.54

= cm

mile

x 1.6

= km

km

x.6214

= mile

Ounces (oz)

x 28.35

= grams (g)

grams (g)

x.035

= Ounces (oz)

cc’s

x.03381

= Fluid Ounces 
(oz)

lbs

x.454

= kg

kg

x 2.2046

= lbs

Cubic Inches

x 16.387

= Cubic 
Centermeters

Cubic Centimeters x.061

= Cubic Inches

Imperial pints

x.568

= liters (l)

liters (l)

x 1.76

= Imperial pints

Imperial quarts

x 1.137

= liters (l)

liters (l)

x.88

= Imperial quarts

Imperial quarts

x 1.201

= US quarts

US quarts

x.833

= Imperial quarts

US quarts

x.946

= liters

liters

x 1.057

= US quarts

US gallon

x 3.785

= liter

liter

x.264

= US gallon

Pounds force per 
square inch (psi)

x 6.895

= Kilo pascals 
(kPa)

Kilo pascals (kPa) x.145

= Pounds force per 
square inch (psi)

1.47

General Information

1

9923311 - 2010-2012 PRO-RIDE RUSH/Switchback/RMK Service Manual

© 2011 Polaris Sales Inc.

Glossary Of Terms

ABDC: After bottom dead center.

ACV: Alternating current voltage.

Alternator: Electrical generator producing voltage 
alternating current.

ATDC: After top dead center.

BBDC: Before bottom dead center.

BDC: Bottom dead center.

BTDC: Before top dead center.

CC: Cubic centimeters.

Center Distance: Distance between center of crankshaft 
and center of driven clutch shaft.

CFI: Cleanfire Fuel Injection fuel management and ignition 
system. In this system, all system and chassis voltage is 
DC.

Chain Pitch: Distance between chain link pins (No. 35 = 
3/8" or 1 cm). Polaris measures chain length in number of 
pitches.

CI: Cubic inches.

Clutch Buttons: Plastic bushings which aid rotation of the 
movable sheave in the drive and driven clutch.

Clutch Offset: Drive and driven clutches are offset so that 
drive belt will stay nearly straight as it moves along the 
clutch face.

Clutch Weights: Three levers in the drive clutch which 
relative to their weight, profile and engine RPM cause the 
drive clutch to close and grip the drive belt.

Crankshaft Run-Out: Run-out or “bend” of crankshaft 
measured with a dial indicator while crankshaft is 
supported between centers on V blocks or resting in 
crankcase. Measure at various points especially at PTO.

CVT: Continuously Variable Transmission (Drive Clutch 
System)

DCV: Direct current voltage.

DC-CFI: Cleanfire Fuel Injection fuel managment and 
ignition system featuring a stator with a separate DCV 
system coil and ACV lighting coil.

DET (Detonation Elimination Technology): Engine 
monitoring and control software that reduces ignition 
timing and/or adds fuel when detonation is detected. 

Dial Bore Gauge: A cylinder measuring instrument which 
uses a dial indicator. Good for showing taper and out-of-
round in the cylinder bore.

Electrical Open: Open circuit. An electrical circuit which 
isn't complete.

Electrical Short: Short circuit. An electrical circuit which 
is completed before the current reaches the intended load. 
(i.e. a bare wire touching the chassis).

End Seals: Rubber seals at each end of the crankshaft.

Engagement RPM: Engine RPM at which the drive clutch 
engages to make contact with the drive belt.

ft.: Foot or feet.

ft-lb: (foot-pound) A force of one pound at the end of a 
lever one foot in length, applied in a rotational direction.

g: Gram. Unit of weight in the metric system.

gal.: Gallon.

ID: Inside diameter.

in.: Inch/inches.

in-lb: (inch pounds) A force of one pound at the end of a 
lever one foot in length, applied in a rotational direction. 12 
in. lbs. = 1 ft. lb.

kg/cm

2

: Kilograms per square centimeter.

kg-m: Kilogram meters.

Kilogram/meter: A force of one kilogram at the end of a 
lever one meter in length, applied in a rotational direction.

l or ltr: Liter.

lbs/in

2

: Pounds per square inch.

Left or Right Side: Always referred to based on normal 
operating position of the driver.

m: Meter/meters.

Mag: Magneto.

1.48

General Information

9923311 - 2010-2012 PRO-RIDE RUSH/Switchback/RMK Service Manual

© 2011 Polaris Sales Inc.

Magnetic Induction: As a conductor (coil) is moved 
through a magnetic field, a voltage will be generated in the 
windings. Mechanical energy is converted to electrical 
energy in the stator.

mi.: Mile/miles.

mm: Millimeter. Unit of length in the metric system. 1 mm 
= approximately .040".

Nm: Newton meters.

OD: Outside diameter.

Ohm: The unit of electrical resistance opposing current 
flow.

oz.: Ounce/ounces.

PERC: Polaris Electronic Reverse Control

Piston Clearance: Total distance between piston and 
cylinder wall.

psi.: Pounds per square inch.

PTO: Power take off.

PVT: Polaris Variable Transmission

qt.: Quart/quarts.

Regulator: Voltage regulator. Regulates battery charging 
system output at approx. 14.5 DCV as engine RPM 
increases.

Reservoir (Surge) Tank: The fill tank in the liquid cooling 
system.

Resistance: In the mechanical sense, friction or load. In 
the electrical sense, ohms, resulting in energy conversion 
to heat.

RPM: Revolutions per minute.

Seized Piston: Galling of the sides of a piston. Usually 
there is a transfer of aluminum from the piston onto the 
cylinder wall.

Stator Plate: The plate mounted under the flywheel 
supporting the battery charging coils.

TDC: Top dead center. Piston's most outward travel from 
crankshaft.

VES: Variable Exhaust System

Volt: The unit of measure for electrical pressure of 
electromotive force. Measured by a voltmeter in parallel 
with the circuit.

Watt: Unit of electrical power. Watts = amperes x volts.

WOT: Wide open throttle.

Engine/Cooling/Exhaust

3.1

CHAPTER 3

Engine/Cooling/Exhaust

3

9923311 - 2010-2012 PRO-RIDE RUSH/Switchback/RMK Service Manual

© 2011 Polaris Sales Inc.

ENGINE SPECIFICATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3

FASTENER TORQUE GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.3
COMPONENT TORQUE SEQUENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.4
ENGINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5
ENGINE SERVICE SPECIFICATIONS - ALL ENGINES  . . . . . . . . . . . . . . . . . . . . . . . . .3.5
VEHICLE/ENGINE MATRIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.6

SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7

SPECIAL TOOLS - ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.7

ENGINE INSPECTIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7

CYLINDER HEAD INSPECTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.7
CYLINDER MEASUREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.8
PISTON INSPECTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.9
PISTON RING INSTALLED GAP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.9
REED VALVE INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.10
BEARING FIT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.10
CRANKSHAFT RUNOUT INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.11
MAIN BEARING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.11
CONNECTING ROD LOWER BEARING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.11
PISTON NEEDLE BEARING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.12
CRANKSHAFT INDEX  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.13
CHECKING CRANKSHAFT INDEX  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.13
CYLINDER HONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.14
HONING TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.14
HONING PROCEDURE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.14
CLEANING THE CYLINDER AFTER HONING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.14
CRANKSHAFT TRUING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.15

ENGINE MOUNTING SYSTEMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16

2010 600 ENGINE MOUNTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.16
2011 600 ENGINE MOUNTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.17
2011 800 ENGINE MOUNTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.18
2012 600/800 ENGINE MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.19
ENGINE MOUNT BOLT SERVICE REPLACEMENT KIT. . . . . . . . . . . . . . . . . . . . . . . .3.20
ENGINE MOUNT SCREW INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.20

RECOIL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.21

ROPE REMOVAL AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.21

ENGINE COMPONENT ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.22

600 CYLINDER HEAD/CYLINDERS/PISTONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.22
600/800 RECOIL/STATOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.24
600 CRANKCASE/CRANKSHAFT ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.26
800 DC-CFI-2 CYLINDER HEAD/CYLINDER/PISTONS  . . . . . . . . . . . . . . . . . . . . . . . .3.28
CYLINDER HEAD/CYLINDER/PISTON NOTES  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.29
800 DC-CFI-2 CYLINDER HEAD/CYLINDER/PISTONS DISASSEMBLY/ASSEMBLY .3.29
800 DC-CFI-2 CRANKCASE/CRANKSHAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.30
800 DC-CFI-2 CRANKSHAFT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.31
600/800 DC-CFI WATER AND OIL PUMP ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . .3.32
OIL HOSE ROUTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.34
ENGINE REMOVAL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.35
ENGINE INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.38

 

 

 

 

 

 

 

Content   ..  10  11  12  13   ..