|
|
NC alarms
Reaction:
NC not ready.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Apply fewer link connections. axes that need connecting through links or combine the axes in fewer containers.
Machine data to be changed:
- MD18781 $MN_NCU_LINK_CONNECTIONS
- MD10002 $MN_AXCONF_LOGIC_MACHAX_TAB
- MD12701 $MN_AXCT_AXCONF_ASSIGN_TAB1 ... and all further container def.
Programm
Switch control OFF - ON.
continuation:
28022
Axis container %1 was declared differently on the NCUs
Parameters:
%1 = Axis container name
Explanation:
An axis container definition must be uniform on all NCUs, with the same values configured.
Reaction:
NC not ready.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Configure the container locations uniformly on all NCUs. Check machine data
MD127..$MN_AXCT_AXCONF_ASSIGN_TAB1...n
Programm
Switch control OFF - ON.
continuation:
28030
Serious alarm on NCU %1, axes in follow-up mode
Parameters:
%1 = NCU number
Explanation:
All axes are trailing because of a serious alarm on another NCU.
Reaction:
NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Acknowledge the alarm on the NCU.
Programm
Restart part program. Clear alarm with the RESET key in all channels of this mode group. Restart part program.
continuation:
28031
Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode
Parameters:
%1 = NCU number
Explanation:
A serious alarm was not yet acknowledged on another NCU. Consequently, all the axes continue to trail.
Reaction:
NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Acknowledge the alarm on the NCU.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
561
NC alarms
Programm
Alarm display showing cause of alarm disappears. No further operator action necessary.
continuation:
28032
Emergency stop activated on NCU %1, axes in follow-up mode
Parameters:
%1 = NCU number
Explanation:
The emergency stop request is active at the PLC-NCK interface on one NCU in the NCU group. Consequently, all axes are
following.
Reaction:
NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Remedy the cause of the emergency stop on the NCU, and acknowledge the emergency stop via the PLC-NCK interface.
Programm
Restart part program. Clear alarm with the RESET key in all channels of this mode group. Restart part program.
continuation:
28033
Emergency stop on NCU %1, axes still in follow-up mode
Parameters:
%1 = NCU number
Explanation:
The emergency stop request is active at the PLC-NCK interface on one NCU in the NCU group. Consequently, all axes are
following.
Reaction:
NC not ready.
Mode group not ready, also effective for single axes.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Remedy the cause of the emergency stop on the NCU, and acknowledge the emergency stop via the PLC-NCK interface.
Programm
Alarm display showing cause of alarm disappears. No further operator action necessary.
continuation:
29033
[Channel %1: ] Axis exchange of axis %2 not possible, PLC axis movement not yet completed
Parameters:
%1 = Channel number
%2 = Axis
Explanation:
A PLC axis has not yet reached its end position and cannot be returned to a channel or neutralized. This alarm should not
occur when PLC data block FC18 is used.
Reaction:
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Remedy:
Wait until the axis has reached the end position or terminate the movement with delete distance to go.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
562
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
4
61000
%[[Channel %1: ] Block %2: %]No tool offset active
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
D-correction must be programmed before the cycle call.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61001
[Channel %1: ] Block %2: Thread pitch incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check parameter for the thread size or setting for the pitch (contradict each other).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61002
%[[Channel %1: ] Block %2: %]Type of machining incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
Modify VARI parameter.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61003
%[[Channel %1: ] Block %2: %]No feed programmed in cycle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Modify feed parameter.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
563
Cycle alarms
61004
[Channel %1: ] Block %2: Incorrect configuration of geometry axes
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61005
[Channel %1: ] Block %2: 3rd geometry axis not available
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
With an application on the turning machine with no Y-axis in the G18 plane.
Remedy:
Check parameter on cycle call.
61006
%[[Channel %1: ] Block %2: %]Tool radius too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool radius is too large for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a smaller tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61007
[Channel %1: ] Block %2: Tool radius too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool radius is too small for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a larger tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61008
[Channel %1: ] Block %2: No tool active
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarm triggered by following cycles:
Remedy:
Select a tool.
Alarms
564
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61009
[Channel %1: ] Block %2: Active tool number = 0
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No tool (T) has been programmed before the cycle call.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program tool (T).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61010
[Channel %1: ] Block %2: Finishing allowance too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Causes of error:
- The finishing allowance for the base is greater than the total depth.
- The finishing allowance at the edge is greater than or equal to the tool diameter.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Reduce finishing allowance.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61011
[Channel %1: ] Block %2: Scaling not permissible
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
A scale factor is active which is illegal for this cycle.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Modify scale factor.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61012
%[[Channel %1: ] Block %2: %]Different scaling in planes
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
565
Cycle alarms
61013
[Channel %1: ] Block %2: Basic settings were changed, program cannot be executed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
The basic settings are not compatible with the generated program.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check and, if necessary, change the basic settings.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61014
[Channel %1: ] Block %2: Return plane exceeded
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Check parameter RTP.
61015
[Channel %1: ] Block %2: Contour is not defined
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61016
[Channel %1: ] Block %2: System frame for cycles missing
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Set MD 28082: MM_SYSTEM_FRAME_MASK, Bit 5=1.
61017
%[[Channel %1: ] Block %2: %]Function %4 not present in NCK
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
566
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61018
[Channel %1: ] Block %2: function %4 not executable with NCK
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61019
%[[Channel %1: ] Block %2: %]Parameter %4 incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Alarm 61019 is output in very many cycles if transfer parameters have been incorrectly programmed.
The alarm text states the name of the incorrect parameter.
Example cycle POCKET3: Parameter _MIDA defined incorrectly.
The specified parameter then has to be checked and changed.
For parameters in which multiple selection options are coded by individual decimal digits, the incorrectly coded digit is also
output.
Example: 61019 parameter (S_MVAR: dec4) defined incorrectly
The value of the 4th decimal place (dec4 -> THOUSANDS digit) of the transfer parameter S_MVAR is defined incorrectly
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
567
Cycle alarms
Remedy:
Check and change the value of the parameter or the corresponding position.
Particular notes for individual cycles:
If error message 61019 comes from CYCLE832, then:
61019 parameter S_TOLM: xx is defined incorrectly
1. Parameter S_TOLM lies outside the value range: S_TOLM UNITS digit 0 to 3. TENS digit 0 or 1
2. Parameter S_TOLM>3 and parameter S_OTOL not programmed and setting data SD55220
$SCS_FUNCTION_MASK_MILL_TOL_SET bit0=0
Remedy:
Set parameter S_TOLM in valid range (0..13), or,
Set the compatibility bit in SD55220 bit0=1 with the field technology when CYCLE832 is called (up to SW 2.6).
If the error message comes from CUST_832:
The manufacturer cycle CUST_832 must be upgraded to the latest cycle version.
If the error message comes from CYCLE9960:
01 MD11160
: Inadequate authorization for writing the kinematic chain
10 VSC_Rotary
: Compile Cycle VCS_Rotary is not fully set up. GUD variable _E996_ACTIV_STATE not present
11 VSC_Rotary
: Compile Cycle VCS_Rotary is not fully set up. Variable $MC_E996_FILE_LOCATION missing
12 VSC_Rotary MD62738 : $MC_E996_FILE_LOCATION incorrectly parameterized
13 VSC_Rotary file
: Too many E996m_ files, only up to _E996m_10
14 VSC_Rotary MD62736 : Compensation limit exceeded
15 VSC_Rotary MODULO : RA is a modulo axis. The measuring range includes $MA_MODULO_RANGE_START,
$MA_MODULO_RANGE_START must be a measuring position
16 VSC_Rotary MODULO : RA is a modulo axis. The measuring range includes $MA_MODULO_RANGE_START, the angle
between the measuring points must be a divisor of $MA_MODULO_RANGE
20 $NT_CNTRL bit7
: With reference head, the vector chain must be open -> $NT_CNTRL bit7=0
21 $SCS_MEA_KIN_MODE[0] DEC2=0 : With reference head, the vector chain must be open.
24 REF HEAD TRAFOTYP
: Reference head only with swivel head or mixed kinematics
25 REF HEAD S_KNUM?
: Parameter S_KNUM=9000, corresponds to active WO
S_KNUM=xx 1(G54) ... 99(G599)
26 REF HEAD
: No head was measured as a reference head _OVR[105]=0 _OVR[105]=transformation number
27 REF Workoffset
: _OVR[104] -> WO measured with the reference head does not match the current value.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61020
[Channel %1: ] Block %2: Machining not possible with active TRANSMIT/TRACYL
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61021
[Channel %1: ] Block %2: Parameter %4 value too high
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Alarms
568
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
For measuring cycles:
- Correct the parameters displayed on the measuring cycle screen or measuring cycle interface.
-For CYCLE63 and trochoidal milling:
- The angle of contact CMAX must be less than or equal to 80° during roughing
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61022
[Channel %1: ] Block %2: Parameter %4 value too low
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
- For CYCLE63 and trochoidal milling:
- The angle of contact CMIN must be greater than 10° during roughing
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61023
[Channel %1: ] Block %2: Parameter %4 value must be unequal to zero
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61024
[Channel %1: ] Block %2: Parameter %4 check value
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
569
Cycle alarms
Remedy:
If the error message comes from CYCLE9960:
Start/end RA1: Set measuring range is not compatible with the traversing range (MD36100) of rotary axis 1.
Start/end RA2: Set measuring range is not compatible with the traversing range (MD36100) of rotary axis 2.
The measuring range is always considered in the clockwise direction from the start to the end
Example: Start = 0°, end = -45°, traversing range of the axis -90°..90° => error because the measuring range is interpreted
from 0° to 315° and not from -45° to 0°
Error message is displayed when measuring the kinematics of a grinding machine:
1st measurement: Starting position is "Beta" = 0°, "Beta" <> 0° leads to the error message
For the 2nd and 3rd measurements, "Beta" has to be rotated further, either in the positive or negative direction. A change
in the direction of rotation leads to the error message.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61025
[Channel %1: ] Block %2: Check tool carrier position
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61026
[Channel %1: ] Block %2: Cycle cannot be executed with NC function %4.
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61027
%[[Channel %1: ] Block %2: %]Subroutine %4 does not exist
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
- Check CYCLE62 call
- Check whether the subroutines specified on CYCLE62 call exist in the program storage
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
570
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61028
[Channel %1: ] Block %2: Contour name %4 too long
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Error message in connection with contour call:
- Use shorter contour name
Error message in connection with contour turning:
-String lengths of the paths of the machined part contour or blank contour (if blank contour) or the updated blank contour
(if residual machining) too long
-Use shorter directory or contour name
Error message in connection with contour milling:
-String lengths of the paths of the pocket/blank contour or the island contours too long
-Use shorter directory or contour name
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61029
%[[Channel %1: ] Block %2: %]Program name %4 too long
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
- use shorter program name
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61030
[Channel %1: ] Block %2: Path not permitted: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61031
[Channel %1: ] Block %2: Path not found: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
571
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61032
[Channel %1: ] Block %2: File not found: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61033
[Channel %1: ] Block %2: Incorrect file type: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61034
[Channel %1: ] Block %2: File is full: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61035
[Channel %1: ] Block %2: File in use: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
572
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61036
[Channel %1: ] Block %2: NC storage limit reached: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61037
[Channel %1: ] Block %2: No access rights to file: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61038
[Channel %1: ] Block %2: Other file error: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61039
[Channel %1: ] Block %2: Line not available: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
573
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61040
[Channel %1: ] Block %2: Line longer than result variable: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61041
[Channel %1: ] Block %2: Line range too large: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61042
[Channel %1: ] Block %2: Program name %4 illegal
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
In the case of multi-channel systems, the main program name must not end with _Cxx (xx stands for figures).
Rename main program.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61043
[Channel %1: ] Block %2: Error affecting coordinate conversion (%4)
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
574
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
1: Type not specified
2: Error during tool identification
3: Meas. point 1 not available
4: Meas. point 2 not available
5: Meas. point 3 not available
6: Meas. point 4 not available
7: No reference point available
8: No direction of approach
9: Meas. points are identical
10: Alpha is incorrect
11: Phi is incorrect
12: Incorrect direction of approach
13: Lines do not intersect
14: Planes not available
15: No frame or incorrect frame selected
16: Not enough memory available
17: Internal error
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61044
%[[Channel %1: ] Block %2: %]Illegal character(s) in file name: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Remove illegal character from file name
Permitted characters are: letters, figures, underscore, slash with path name
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61045
[Channel %1: ] Block %2: Job list not found: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The specified job list could not be found.
Check name and contents of job list.
The job list must be in the same workpiece as the part program.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
575
Cycle alarms
61046
[Channel %1: ] Block %2: Part program not found in job list: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Part program (main program) not found in specified job list in respective channel.
Check name and contents of job list.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61047
[Channel %1: ] Block %2: Label name %4 too long
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
- select shorter label name
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61048
[Channel %1: ] Block %2: Multi-channel data not found in job list: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Multi-channel data not found in job list.
Correct job list.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61049
[Channel %1: ] Block %2: 1st spindle not programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program 1st spindle in the screen.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
576
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61050
[Channel %1: ] Block %2: Spindle programmed twice
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The same spindle was programmed twice.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Leave 2nd spindle empty or program other spindle.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61051
%[[Channel %1: ] Block %2: %]Program name assigned twice
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The same program name was assigned twice.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
When using CYCLE952, the name of the main program must not be the same as the name of the cutting file (PRG) or the
name of the updated blank contour (CONR).
When using CYCLE63 and/or CYCLE64, the name of the main program must not be the same as the name of the program
to be generated (PRG).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61052
[Channel %1: ] Block %2: Maximum spindle speed for main spindle not entered
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Max. speed for main spindle was not entered.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter speed limit in program header or under settings.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61053
[Channel %1: ] Block %2: Maximum spindle speed not entered for counterspindle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Maximum speed of counterspindle was not entered.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter speed limit in program header or under settings.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
577
Cycle alarms
61054
[Channel %1: ] Block %2: Programs started from various job lists: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Programs from various job lists were started simultaneously.
This is illegal. All programs must be assigned to the same job list.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select desired job list again, and start programs afresh.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61055
[channel %1: ] block %2: magazine location number too low: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The magazine location number entered was too low.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61056
[channel %1: ] block %2: magazine location number too high: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The magazine location number entered was too high.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61057
[Channel %1: ] Block %2: magazine location number is no integer: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The magazine location number must be an integer.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
578
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61058
%[[channel %1: ] block %2: %]Function %4 not released
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
- CYCLE952: balance cutting function must be released via MD52218 $MCS_FUNCTION_MASK_TURN, bit6.
- CYCLE953: option for the SFT function must be set.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61059
%[[Channel %1: ] Block %2: %]Tool preselection failed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
--
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61060
%[[Channel %1: ] Block %2: %]Function requires tool management
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
--
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61061
%[[Channel %1: ] Block %2: %]Different scaling in the plane and depth
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
579
Cycle alarms
61062
%[[Channel %1: ] Block %2: %]Axis position %4incorrectly programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check the last programmed axis position
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61063
%[[Channel %1: ] Block %2: %]Tool at magazine location %4 is not a multitool
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
A magazine location and a multitool location were programmed. However, there is no multitool at the magazine location.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Only program the magazine location (without multitool location).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61064
%[[Channel %1: ] Block %2: %]Invalid multitool location: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
A multitool location was programmed, at which there is no multitool.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program a valid multitool location.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61065
[Channel %1: ] Block %2: A channel specified in the job list does not exist: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
A non-existent channel was specified in the job list.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Correct job list
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
580
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61066
%[[Channel %1: ] Block %2: %]Cycle %4 requires G code G70 or G71
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Cycle requires G code G70 or G71
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program G70 or G71
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61067
[Channel %1: ] Block %2:Tool spindle is in spindle mode: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
To activate the turning transformation, the tool spindle must be in axis mode. But it is in spindle mode.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Before activating the turning transformation, put the tool spindle in axis mode (with SPOS or M70).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61068
[Channel %1: ] Block %2: Cycle requires G code %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An incorrect G code is active when the cycle is called.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Activate the stated G code before calling the cycle. Multiple G codes may be presented for selection.
Example: Cycle requires G code: G70/G71
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61069
[Channel %1: ] Block %2: Axis not referenced %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
A referenced axis is required in the cycle, but an unreferenced axis was detected.
If possible, the axis identifier is stated in the alarm text.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Reference axis before calling the cycle.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
581
Cycle alarms
61070
[Channel %1: ] Block %2: Incorrect tool type for 'shank' selection
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
For the "shank" selection, the tool must have an acute angle.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Use "tip" selection.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61071
%[[Channel %1: ] Block %2: %] Option for EES missing
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
When a part program is called via EXTCALL without EES, the contour can only be called via "Contour name" or "Labels".
This means that contour calls via "Subroutine" or "Labels in subroutine" are only possible if EES is active.
Error message from CYCLE996:
The data record can only be stored on external memory if option EES is set.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
- Program contour call via "Contour name" or "Labels"
- Error message from CYCLE996:
Set the option or do not start the program from external memory.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61072
%[[Channel %1: ] Block %2: %]: Error code %4 on activating the intelligent load adjustment
function
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An error occurred when activating an adaptation table for adapting the loading of the machine (language command
CADAPTON).
Error message from CYCLE782
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Error code:
1
: No valid adaptation table parameterized -> the commissioning of the adaptation tables must be checked
2
: Axis name parameter invalid -> check axis
3
: Input variable parameter invalid -> check value
5
: Input value parameter invalid -> check value
99: Internal error
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
582
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61073
%[[Channel %1: ] Block %2: %]: Error code %4 on deactivating the intelligent load adjustment
function
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An error occurred when deactivating an adaptation table for adapting the machine loading (language command
CADAPTOF).
Error message from CYCLE782
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Error code:
1
: No valid adaptation table parameterized -> the commissioning of the adaptation tables must be checked
2
: Axis name parameter invalid -> check axis
3
: Input variable parameter invalid -> check value
5
: Input value parameter invalid -> check value
99: Internal error
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61074
%[[{Channel %1: ] Block %2: %] Number of traversing blocks for spline formation is too low
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The number of traversing blocks for spline formation is too low.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enlarge the program section and thus the number of traversing blocks
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61075
%[[Channel %1: ] Block %2: %]Cycle %4 does not run in the handling channel.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified cycle does not run in the handling channel.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Execute the program containing the cycle to be called in the machining channel.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61076
%[[Channel %1: ] Block %2: %]Cycle %4 does not support interpolated turning.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified cycle does not support interpolated turning.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
583
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Disable interpolated turning
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61077
%[[Channel %1: ] Block %2: %]Program does not run in a handling channel
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The current program can only be executed in one machining channel.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Execute the program in one machining channel
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61098
[Channel %1: ] Block %2: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
This alarm is used for various purposes.
Please refer to the alarm text.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Depends on alarm text
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61099
[Channel %1: ] Block %2: Internal cycle error (%4)
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61100
%[[Channel %1: ] Block %2: %]Rotated flat surface cannot be calculated
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The flat surface cannot be calculated with the selected turning angle alpha0 and the specifications abs/inc for X1/Y1.
Alarms
584
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The corner point X1/Y1 must be specified in a different way, e.g. with incremental values.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61101
%[[Channel %1: ] Block %2: %]Reference point defined incorrectly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
With an incremental specification of the depth, either different values have to be selected for the reference point (reference
plane) and the retraction plane, or an absolute value must be specified for the depth.
When machining in the "manual machine" area, the following setting data must be checked and adapted to the machining.
SD 55260 $SCS_MAJOG_SAFETY_CLEARANCE (value greater than zero)
SD 55261 $SCS_MAJOG_RELEASE_PLANE
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61102
%[[Channel %1: ] Block %2: %]No spindle direction programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Parameter SDIR (or SDR in CYCLE840) must be programmed.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61103
[Channel %1: ] Block %2: Number of holes is zero
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
Check parameter NUM.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61104
[Channel %1: ] Block %2: Contour violation of slots
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Incorrect parameterization of the milling pattern in the parameters which define the position of the slots/elongated holes
on the circle and their form.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
585
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61105
[Channel %1: ] Block %2: Milling cutter radius too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The diameter of the cutter used is too large for the form to be machined.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Either a tool with a smaller radius has to be used or the contour must be modified.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61106
[Channel %1: ] Block %2: Number of or distance between circular elements
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Incorrect parameterization of NUM or INDA. The layout of the circle elements within a full circle is not possible.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Correct parameterization.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61107
[Channel %1: ] Block %2: First drilling depth incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Modify drilling depth.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61108
[Channel %1: ] Block %2: Illegal values for radius and insertion depth parameters
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The radius (_RAD1) and insertion depth (_DP1) parameters for defining the helix path for the depth infeed have been
incorrectly specified.
Alarms
586
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Modify parameter.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61109
%[[Channel %1: ] Block %2: %]Milling direction parameter incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The value of the parameter for the cutting direction _CDIR has been incorrectly defined.
Remedy:
- Change milling direction.
- During pocket machining (CYCLE63), the selected milling direction must match the milling direction of centering/rough
drilling.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61110
[Channel %1: ] Block %2: Finishing allowance at the base is greater than the depth infeed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The finishing allowance at the base has been specified greater than the maximum depth infeed.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Either reduce finishing allowance or increase depth infeed.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61111
[Channel %1: ] Block %2: Infeed width is greater than the tool diameter
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The programmed infeed width is greater than the diameter of the active tool.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Infeed width must be reduced.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61112
[Channel %1: ] Block %2: Tool radius negative
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The radius of the active tool is negative. This is illegal.
Remedy:
Change the tool radius.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
587
Cycle alarms
61113
[Channel %1: ] Block %2: Parameter for corner radius too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The parameter for the corner radius _CRAD has been specified too large.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Reduce corner radius
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61114
[Channel %1: ] Block %2: Machining direction G41/G42 incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The machining direction of the cutter radius compensation G41/G42 has been incorrectly selected.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Change machining direction.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61115
[Channel %1: ] Block %2: Approach or retract mode(straight / circle / plane / space) incorrectly
defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The approach or retract mode to/from the contour has been incorrectly defined.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check parameter _AS1 or _AS2.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61116
[Channel %1: ] Block %2: Approach or retract path = 0
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The approach or retract path has been specified with zero.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check parameter _LP1 or _LP2.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
588
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61117
%[[Channel %1: ] Block %2: %]Active tool radius is smaller than or equal to zero
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The radius of the active tool is negative or zero.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Modify radius.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61118
[Channel %1: ] Block %2: Length or width = 0
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The length or width of the milling area is illegal.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check parameters _LENG and _WID.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61119
[Channel %1: ] Block %2: Nominal or core diameter programmed incorrectly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The nominal or core diameter was incorrectly programmed.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check thread geometry.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61120
[Channel %1: ] Block %2: Thread type inside / outside not defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The thread type (internal/external) was not defined.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The internal/external thread type must be entered.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
589
Cycle alarms
61121
[Channel %1: ] Block %2: Number of teeth per cutting edge is missing
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No value was entered for the number of teeth per cutting edge.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter the number of teeth/cutting edges for the active tool into the tool list.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61122
[Channel %1: ] Block %2: Safety distance incorrectly defined in plane
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The safety clearance is negative or zero. This is not allowed.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Define the safety clearance.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61123
[Channel %1: ] Block %2: CYCLE72 cannot be simulated
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61124
[Channel %1: ] Block %2: Infeed width is not programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
With active simulation without tool, a value for the infeed width _MIDA must always be programmed.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
590
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61125
[Channel %1: ] Block %2: Technology selection parameter incorrectly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check technology selection parameter (_TECHNO).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61126
[Channel %1: ] Block %2: Thread length too short
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program lower spindle speed or raise reference point (reference plane).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61127
[Channel %1: ] Block %2: Wrong definition of tapping axis transformation ratio (machine data)
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check machine data 31050 and 31060 in the appropriate gear stage of the drilling axis.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61128
[Channel %1: ] Block %2: Insertion angle = 0 for insertion with oscillation or helix
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check parameter _STA2.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
591
Cycle alarms
61129
[Channel %1: ] Block %2: perpendic. approach and retraction during contour milling only
allowed with G40
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61130
[Channel %1: ] Block %2: positions of parallel axes cannot be compensated. No workpiece
reference agreed.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61131
[Channel %1: ] Block %2: parameter _GEO incorrect, _GEO=%4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61132
[Channel %1: ] Block %2: Parallel axis parameters incorrect, check values for parallel axis
parameters ABS/INK
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
592
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61133
[Channel %1: ] Block %2: 3rd parallel axis parameter incorrect, check axis name or GUD
_SCW_N[]
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61134
[Channel %1: ] Block %2: Rotary axis parameters incorrect, check values for rotary axis
parameters ABS/INK
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61135
[Channel %1: ] Block %2: incorrect parameter sequence for approaching target position: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61136
[Channel %1: ] Block %2: no 3rd geometry axis agreed in GUD _SCW_N[]
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
593
Cycle alarms
61137
[Channel %1: ] Block %2: swiveling and parallel axes cycle are mutually exclusive because of
workpiece reference $P_WPFRAME
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61138
[Channel %1: ] Block %2: parameter %4 incorrectly defined for tool monitoring in cycles
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61139
[Channel %1: ] Block %2: error in function Tool monitoring in cycles
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61140
[Channel %1: ] Block %2: Main spindle is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 35000 $MA_SPIND_ASSIGN_TO_MACHAX[]
MD 52206 $MCS_AXIS_USAGE[]
Alarms
594
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61141
[Channel %1: ] Block %2: C axis of the main spindle is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 35000 $MA_SPIND_ASSIGN_TO_MACHAX[]
MD 52206 $MCS_AXIS_USAGE[]
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61142
[Channel %1: ] Block %2: Counterspindle is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 35000 $MA_SPIND_ASSIGN_TO_MACHAX[]
MD 52206 $MCS_AXIS_USAGE[]
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61143
[Channel %1: ] Block %2: C axis of the counterspindle is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 35000 $MA_SPIND_ASSIGN_TO_MACHAX[]
MD 52206 $MCS_AXIS_USAGE[]
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
595
Cycle alarms
61144
[Channel %1: ] Block %2: Tool spindle is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 35000 $MA_SPIND_ASSIGN_TO_MACHAX[]
MD 52206 $MCS_AXIS_USAGE[]
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61145
[Channel %1: ] Block %2: Linear axis of the counterspindle is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 52206 $MCS_AXIS_USAGE[]
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61146
[Channel %1: ] Block %2: B axis is not set up correctly
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please check the following machine or setting data:
MD 20070 $MC_AXCONF_MACHAX_USED[]
MD 20080 $MC_AXCONF_CHANAX_NAME_TAB[]
MD 35000 $MA_SPIND_ASSIGN_TO_MACHAX[]
MD 52206 $MCS_AXIS_USAGE[]
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61147
[Channel %1: ] Block %2: Transformation not active: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Alarms
596
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The stated transformation is not active.
You have to activate the transformation before you can use it.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61148
[Channel %1: ] Block %2: Swivel plane with active turning tool not possible
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Swiveling the plane is not possible when a turning tool is active.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Load a milling tool before you swivel the plane.
The alarm can be suppressed using SD 55410 $SCS_MILL_SWIVEL_ALARM_MASK.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61149
[Channel %1: ] Block %2: Positioning a milling tool with active turning tool is not possible
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Milling tools cannot be positioned if a turning tool is active.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Load a milling tool, before you call positioning.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61150
[Channel %1: ] Block %2: Tool cannot be aligned - error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
597
Cycle alarms
Remedy:
Error code:
A: Only new swivel plane permitted, see parameter _ST
B: Angular range >= 360 -> angular range of the B axis >= 360 degrees
C: Rotary axis vector V1 is not equal to 0 1 0 -> rotary axis vector V1 must rotate around Y
See setup of swivel CYCLE800
D: Rotary axis vector V2 -> rotary axis vector V2 must rotate around X (1 0 0) or Z (0 0 1)
See setup of swivel CYCLE800
E: WCS ROT Y > 90 -> active rotation of the Work (WCS) around Y is >90 degrees. -90 to +90 is permitted
F: If geometry axis Y is not available -> SD55221 set bit 5 = 1
G: Initial setting defines ($TC_CARR37] HUNDREDTHOUSANDS digit -Z or -X) -> SD55221 set bit 5 = 1
See setup of swivel CYCLE800
H: Align tool, but active plane not G18
I: 1st turning technology (MD52200=1) and no Y axis available -> mirroring not allowed
J: 1st turning technology (MD52200=1) and no Y axis available -> rotation around Y not possible
K: Grinding technology (MD52200=3) and align tool -> SD55221 set bit 5=1
L: Grinding technology (MD52200=3) and align tool -> set MD20186 = 1
61151
[Channel %1: ] Block %2: Orientation of tool not possible - error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
Causes of error:
1st error code = A -> only additive swivel plane permitted, see parameter _ST
61152
[Channel %1: ] Block %2: B axis kinematics (turning technology) either not or incorrectly set
up in Start-up of swivel cycle - error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
Causes of error:
1st error code = A123 -> B axis not an automatic rotary axis under ShopTurn (123 corresponds to parameter _TCBA)
2nd error code = B123 -> B axis not activated in swivel cycle start-up (kinematics)
(123 corresponds to $TC_CARR37[n], n ... number of the swivel data record)
61153
[Channel %1: ] Block %2: No 'Rotary axes direct' swivel mode possible - error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
598
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Remedy:
Error code:
A -> No tool or no cutting edge (D1..) active
B -> Swivel "no" and swivel "direct", swivel plane "additive" not permitted
C -> Input value for rotary axis 1 not in the grid of the Hirth tooth system
D -> Input value for rotary axis 2 not in the grid of the Hirth tooth system
E -> Swivel "direct" programmed in automatic, but swivel cycle not started up ($TC_CARR37 UNITS digit < =2)
F -> ROT ? G5.. rotation in settable WO (G54..) active, not permitted
ROT ? SETFRAME rotation in basic reference active, not permitted
ROT ? CHBFRAME rotation in basic active, not permitted
G: WPFRAME ? swivel mode additive and translations in workpiece reference (WPFRAME) not permitted
H: X0,Y0,Z0 not equal to 0, swivel mode additive and translations not permitted before swivel
See parameter S_ST 1st decimal place
I: Turning machine and initial setting -X or -Z not possible in G18
J: Turning machine and initial setting -X or -Z and counterspindle mirrored around Z
K: Turning machine and initial setting -Z and G19 not allowed
Initial setting, see setup of swivel CYCLE800
Note on error codes F, G, H:
If the Work (WCS) is rotated before programming swivel direct, and the swivel plane is rotated and moved additively,
alarm 61153 is reported with error code F, G or H in order to avoid an impermissible mixing of frame operations
and direct machine positions.
Alternatively, the machining program can be reprogrammed with swivel axis for each axis and swivel plane new or
additionally,
or with new swivel and swivel plane.
61154
%[[Channel %1: ] Block %2: %]Final depth wrongly programmed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Input of end depth possible only absolutely or incrementally
61155
[Channel %1: ] Block %2: Unit for plane infeed wrongly programmed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Unit for plane infeed possible only in mm or % of tool diameter
61156
[Channel %1: ] Block %2: Depth calculation wrongly programmed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Depth calculation possible only with or without SDIS
61157
%[[Channel %1: ] Block %2: %]Reference point wrongly programmed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
- Check reference point in screenform, input only -X, centered or +X
- During calibration of the length of the infeed axis in JOG, two causes can cause this alarm:
1. The value of the reference workpiece was incorrectly programmed in the parameterization screenform.
2. The length of the workpiece probe in the infeed axis has been incorrectly entered in the tool data.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
599
Cycle alarms
61158
%[[Channel %1: ] Block %2: %]Machining plane wrongly programmed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Check machining plane (G17, G18 or G19) in connection with the parameter _DMODE
61159
[Channel %1: ] Block %2: Machining plane on cycle call differs from the one in the position
pattern
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Adjust the machining plane on cycle call to the machining plane in the position pattern.
61160
[Channel %1: ] Block %2: Residual material remains stationary, reduce plane infeed
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
Reduce plane infeed or slot width, or use milling cutter with larger diameter
61161
[Channel %1: ] Block %2: Centering diameter or tool parameter (diameter, tip angle) are
incorrect
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
- Diameter of centering with tip angle of active tool not possible
- Entered workpiece diameter, tool diameter or tip angle of tool incorrect
- Diameter of tool only has to be entered if centering is to be on workpiece diameter.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61162
[Channel %1: ] Block %2: Tool parameter diameter or tip angle incorrect
Parameters:
%1 = Channel number
%2 = Block number, label channel number
Explanation:
Remedy:
- The tool parameter diameter or tip angle must be greater than zero
- Tip angle must be less than 180°
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61163
[Channel %1: ] Block %2: Infeed width in the plane too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
--
61164
[Channel %1: ] Block %2: Transformation has incorrect type %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
600
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Remedy:
The transformation has the incorrect type. Correct the transformation set up.
61165
[Channel %1: ] Block %2: Transformation set up incorrectly: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
The transformation has been set up incorrectly. Correct the transformation set up.
61166
[Channel %1: ] Block %2: Check machine data: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
The machine data must be checked. Adapt the setting of the machine data.
61167
[Channel %1: ] Block %2: Transformation not set up or not active: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
The specified transformation is not set up or not active. Set up or activate the transformation.
61168
[Channel %1: ] Block %2: Incorrect machining plane: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Remedy:
The machining plane is incorrect. Program correct machining plane.
61169
[Channel %1: ] Block %2: Spindle incorrectly programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An incorrect spindle was programmed.
Remedy:
Change the spindle selection.
61170
[Channel %1: ] Block %2: Incorrect block plane (%4)
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An invalid block plane was used.
Remedy:
Use a valid block plane.
It is only permissible that the block planes are used in an ascending sequence.
61171
[Channel %1: ] Block %2: Block plane used twice (%4)
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The same block plane was used twice.
Remedy:
Only nest the block planes in an ascending sequence.
61172
[Channel %1: ] Block %2: Spindle groups must not be nested
Parameters:
%1 = Channel number
%2 = Block number, label
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
601
Cycle alarms
Explanation:
You have used spindles in several nested groups.
Remedy:
Only use one spindle in one group plane with nested groups.
61173
[Channel %1: ] Block %2: Supplementary run-in code only possible with spindle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The supplementary run-in code can only be used in one block with spindle.
Remedy:
Use a block with spindle.
61174
[Channel %1: ] Block %2: Not possible to align milling tool with active turning tool
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
It is not possible to align milling tools with an active turning tool.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Load a milling tool before you call alignment.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61175
[Channel %1: ] Block %2: angle of aperture programmed too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The angle of aperture of the text (_DF) in the engraving cycle is too small. This means that the text for engraving does not
fit in the specified angle.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter a larger angle of aperture.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61176
[Channel %1: ] Block %2: text length programmed too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The text length (_DF) in the engraving cycle is too short. This means that the text for engraving is longer than the specified
text length.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter longer text length
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61177
[Channel %1: ] Block %2: polar text length > 360 degrees
Parameters:
%1 = Channel number
%2 = Block number, label
Alarms
602
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Explanation:
In the engraving cycle, the polar text length must not exceed 360 degrees.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter shorter text length.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61178
[Channel %1: ] Block %2: code page not present
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified code page is not supported by the cycle.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Use code page 1252.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61179
[Channel %1: ] Block %2: character does not exist, no.: %4
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = Character number
Explanation:
The character entered in the text for engraving cannot be milled.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter another character.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61180
[Channel %1: ] Block %2: No name assigned to swivel data record
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Although there are several swivel data blocks, no unique names have been assigned.
Remedy:
Assign unique name to swivel data block ($TC_CARR34[n]), if machine data 18088 $MN_MM_NUM_TOOL_CARRIER is >1.
61181
[Channel %1: ] Block %2: NCK software version is insufficient for the Swivel function
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Swivelling is not possible with the current NCK software version.
Remedy:
Upgrade NCK software to NCK 75.00 or higher.
61182
[Channel %1: ] Block %2: Name of swivel data record unknown: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified name of the swivel data block is unknown.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
603
Cycle alarms
Remedy:
Check name of swivel data record $TC_CARR34[n].
61183
[Channel %1: ] Block %2: Swivel CYCLE800: Retraction mode parameter lies outside value
range: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The value of the retraction mode parameter (_FR) lies outside the valid range.
Remedy:
Swivel CYCLE800: Check transfer parameter _FR. Value range 0 to 8
61184
[Channel %1: ] Block %2: No solution possible with current input angle values
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The surface defined via the input angle cannot be processed with the machine.
Remedy:
-Check the angles entered for swiveling the machining plane: %4
-Parameter _MODE coding incorrect, e.g. rotation axis-wise YXY
61185
[Channel %1: ] Block %2: Invalid angular ranges of rotary axes in swivel data record: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The angular range of the rotary axes is invalid.
Check setup of the swivel CYCLE800.
Parameter $TC_CARR30[n] to $TC_CARR33[n] n number of swivel data record
Example: Rotary axis 1 modulo 360 degrees: -> $TC_CARR30[n]=0 $TC_CARR32[n]=360
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check setup of swivel cycle CYCLE800.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61186
[Channel %1: ] Block %2: Invalid rotary axis vectors --> Check setup of the swivel cycle
CYCLE800.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No or incorrect entry for rotary axis vector V1 or V2.
Remedy:
Check commissioning of swivel CYCLE800
Check rotary axis vector V1xyz: $TC_CARR7[n], $TC_CARR8[n], $TC_CARR9[n]
Check rotary axis vector V2xyz: $TC_CARR10[n], $TC_CARR11[n], $TC_CARR12[n]
If 2nd rotary axis not available ($TC_CARR35[n]=""), then it is possible that V2xyz=0
n Number of the swivel data set
61187
[Channel %1: ] Block %2: Check setup of the swivel cycle CYCLE800. - Error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
604
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Remedy:
Error code: See current cycles software version notes in siemense.txt
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61188
[Channel %1: ] Block %2: No axis name agreed for rotary axis 1 -> Check setup of the swivel
cycle CYCLE800.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No axis name was specified for the rotary axis 1.
Remedy:
Check setup of swivel CYCLE800.
Axis name of rotary axis 1 see parameter $TC_CARR35[n] n number of swivel data record
61189
[Channel %1: ] Block %2: Swivel direct: Invalid rotary axis positions: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Swivel direct: Check input values of rotary axes.
Remedy:
Swivel mode direct: check the input values of the rotary axes or commissioning for swivel CYCLE800.
Check angular range of rotary axes in swivel data record n:
Rotary axis 1: $TC_CARR30[n], $TC_CARR32[n]
Rotary axis 2: $TC_CARR31[n], $TC_CARR33[n]
If values are entered in the work offset (WO) of the rotary axes, and machine data MD21186=0:
Value in WO of the rotary axis does not correspond to the angular range, rotary axis 1 or 2
Value in WO of the rotary axis plus input value does not correspond to the angular range, rotary axis 1 or 2
Note: for modulo axes, for swivel direct, the input value is calculated in the modulo range
Example: angular range, rotary axis modulo 0 up to 360 input value =-21 rotary axis moves to 339 degrees
61190
[Channel %1: ] Block %2: Unable to retract prior to swiveling -> Error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
605
Cycle alarms
Remedy:
If tool carrier is active, check commissioning of swivel CYCLE800. Parameter $TC_CARR37[n] 7th and 8th decimal places
n number of swivel data set
If align turning tool with milling/turning machine (transformation on basic kinematic chain) is active,
check parameter $NT_IDENT[n,0] 7th and 8th decimal places (n = name of transformation)
Error code:
A: Retraction Z not set up
B: Retraction Z XY not set up
C: Retraction in tool direction max. not set up
D: Retraction in tool direction incremental not set up
E: Retraction in tool direction: NC function CALCPOSI reports error
For the CALCPOSI function, the axes must be referenced. Check machine data MD20700.
F: Retraction in tool direction: no tool axis available
Missing geometry axis (tool axis) Z with G17, Y with G18 or X with G19
G: Retraction in tool direction max.: negative retraction path
H: Retraction in tool direction incremental: negative retraction path not permitted
I: Retraction commissioning swivel CYCLE800 not set up
J: Retraction in tool direction is not permitted, because current Work (WCS) is mirrored
Tool carrier is active
K: Retraction and swivel plane and transformation on basic kinematic chain are active
Retraction with transformation only if align turning tool is active
L: Retraction in tool direction and align tool are only permitted if SD42954 $SC_TOOL_ORI_CONST_M=0
Transformation on basic kinematic chain is active
M: Retraction in tool direction and align tool are only permitted if SD42956 $SC_TOOL_ORI_CONST_T=0
Transformation on basic kinematic chain is active
N: Retraction in tool direction and swivel plane toward counterspindle are not possible
Turning machine with active tool carrier and initial setting -X (see setup swivel)
O: Retraction in tool direction, align tool with counterspindle is not possible
P: Retraction in tool direction in G18 toward counterspindle is not possible
Q: Retraction in tool direction is not permitted because the current Work (WCS) is mirrored
Align turning tool with milling/turning machine (transformation on basic kinematic chain) active
R: Retraction in tool direction is not possible with align tool
Align turning tool with milling/turning machine (transformation on basic kinematic chain) active
61191
[Channel %1: ] Block %2: Multi-axis transformation not set up. Error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Error code:
Number or parameter name of multi-axis transformation
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61192
[Channel %1: ] Block %2: Additional multi-axis transformations not set up. Error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Alarms
606
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Error code:
Number or parameter name of multi-axis transformation
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61193
[Channel %1: ] Block %2: compressor option not set up
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61194
[Channel %1: ] Block %2: spline interpolation option not set up
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61195
[Channel %1: ] Block %2: Aligning a turning tool is only possible with active turning tool
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Aligning turning tools is only possible with one active turning tool.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Change a turning tool, before you call alignment.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61196
[Channel %1: ] Block %2: No swiveling in JOG --> Multi-axis transformations and TCARR
activated at the same time
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Multi-axis transformations (TRAORI) and Toolcarrier (TCARR) activated at the same time.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
607
Cycle alarms
Remedy:
Deselection of multi-axis transformation with TRAFOOF
or deselection of Toolcarrier (TCARR) with CYCLE800()
61197
[Channel %1: ] Block %2: Swiveling - plane not allowed -> Error code %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Error code:
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61198
[Channel %1: ] Block %2: Swiveling with kinematic chain -> Error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
--
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61199
[Channel %1: ] Block %2: Swiveling - tool not allowed -> Error code: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Error is also output if no swivel data record is active and only tool approach is programmed.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
A CYCLE800 must be called with a valid swivel data record before orientation.
Error code:
A: Orientation of tool and change of swivel data record not allowed
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61200
[Channel %1: ] Block %2: Too many elements in machining block
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The machining block contains too many elements.
Remedy:
Check the machining block, delete some elements if required.
61201
[Channel %1: ] Block %2: Wrong sequence in machining block
Parameters:
%1 = Channel number
%2 = Block number, label
Alarms
608
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Explanation:
The sequence of elements in the machining block is invalid.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Sort the sequence in the machining block.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61202
[Channel %1: ] Block %2: No technology cycle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No technology cycle was programmed in the machining block.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program a technology block.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61203
[Channel %1: ] Block %2: No position cycle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No positioning cycle was programmed in the machining block.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program positioning block.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61204
[Channel %1: ] Block %2: Technology cycle unknown
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified technology cycle in the machining block is unknown.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Delete and reprogram the technology block.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61205
[Channel %1: ] Block %2: Position cycle unknown
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified positioning cycle in the machining block is unknown.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
609
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Delete and reprogram the positioning block.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61206
[Channel %1: ] Block %2: Synchronizing possible only when using a job list
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Synchronizing with a counterspindle step in another channel is possible only if a job list is used.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Create job list and add programs for the individual channels.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61207
[Channel %1: ] Block %2: No counterspindle step found for synchronizing
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No counterspindle step was found in any channel with which this channel could synchronize.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Control program.
Delete step for synchronizing if it is not required.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61208
[Channel %1: ] Block %2: Assign parameters for main spindle chuck in the spindle chuck data
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The parameters for the main spindle chuck in the spindle chuck data are not assigned.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Indicate parameters ZCn, ZSn and ZEn in the screen "Parameters" > "Setting data" > "Spindle chuck data".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61209
[channel %1: ] block %2: counterspindle step programmed in several channels
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Counterspindle step may be programmed in one channel only.
Alarms
610
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The step "Counterspindle: synchronizing" must be used in the other channels.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61210
[Channel %1: ] Block %2: Block search element not found
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The element specified for the block search does not exisit.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Repeat block search.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61211
[Channel %1: ] Block %2: Absolute reference missing
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An incremental indication was made, but the absolute reference is unknown.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program an absolute position prior to using incremental indications.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61212
%[[Channel %1: ] Block %2: %]Wrong tool type
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool type is not suitable for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a new tool type.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61213
[Channel %1: ] Block %2: Circle radius too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The programmed circle radius is too small.
Remedy:
Correct the circle radius, center point or end point.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
611
Cycle alarms
61214
[Channel %1: ] Block %2: No pitch programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No thread/helical pitch has been entered.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Program a pitch.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61215
[Channel %1: ] Block %2: Unfinished dimension incorrectly programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Check the blank spigot dimensions. The blank spigot must be larger than the production part spigot.
Remedy:
Check parameters _AP1 and _AP2.
61216
%[[Channel %1: ] Block %2: %]Feed/tooth only possible with cutting tools
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Feed per tooth is only possible with milling tools.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
As alternative, set a different feed type.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61217
[Channel %1: ] Block %2: Cutting speed programmed for tool radius 0
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
To be able to work with cutting speed, the tool radius has to be specified.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter a value for cutting speed.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61218
[Channel %1: ] Block %2: Feed/tooth programmed, but number of tools equals zero
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
For feed per tooth, the number of teeth has to be specified.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
612
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Remedy:
Enter the number of teeth on the milling tool in the "Tool list" menu.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61219
[Channel %1: ] Block %2: Tool radius too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool radius is too large for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a suitable tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61220
[Channel %1: ] Block %2: Tool radius too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool radius is too small for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a suitable tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61221
[Channel %1: ] Block %2: No tool active
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No tool active.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a suitable tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61222
[Channel %1: ] Block %2: Plane infeed greater than tool diameter
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The plane infeed must not be greater than the tool diameter.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Reduce plane infeed.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
613
Cycle alarms
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61223
[Channel %1: ] Block %2: Approach path too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The approach path must not be less than zero.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter a greater value for the approach path.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61224
[Channel %1: ] Block %2: Retract path too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The retract path must not be less than zero.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter a greater value for the retract path.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61225
[Channel %1: ] Block %2: Swivel data record unknown
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
An attempt was made to access a swivel data block which has not been defined.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select another swivel data block or define a new swivel data block.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61226
[Channel %1: ] Block %2: Swivel head cannot be exchanged
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The parameter "Swivel data block" is set to "No". In spite of this, an attempt has been made to change the swivel head.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Set the parameter "Swivel data block" in the setup screen "Rotary axes" to "Automatic" or "Manual".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
614
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61227
[Channel %1: ] Block %2: Target position cannot be reached: %4
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The target position of the approach motion is outside the software limit switch. This situation may arise from swiveling or
coordinate rotations.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
If possible, lower retraction plane. Select alternative solution for swiveling (direction +/-) or clamp on workpiece differently.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61228
[Channel %1: ] Block %2: Retraction plane for swiveling with swivel head not reached due to
software limit switches
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Retraction plane not reached!
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Correct retraction plane
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61229
[Channel %1: ] Block %2: The external retraction plane must be greater than the internal
retraction plane
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The external retraction plane must be greater than the internal retraction plane.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Correct the retraction planes.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61230
[Channel %1: ] Block %2: Tool probe diameter too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool probe has not been calibrated correctly.
Remedy:
840D sl - up to SW 1.x:
Check the following variables in data block GUD7: E_MESS_MT_DR[n] or E_MESS_MT_DL[n] for probe n+1
840D sl/828D - as from SW 2.5:
Check the following machine or setting data: 51780 $MNS_J_MEA_T_PROBE_DIAM_RAD[n]
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
615
Cycle alarms
61231
[Channel %1: ] Block %2: ShopMill program %4 not executable, as not tested by ShopMill
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = Program name
Explanation:
Before a ShopMill program can be executed, it has to be tested by ShopMill.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The program first has to be simulated in ShopMill or loaded into the operating mode "Machine auto" by ShopMill.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61232
[Channel %1: ] Block %2: Impossible to load magazine tool
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Only manual tools may be loaded into a swivel head in which only manual tools can be loaded.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Load a manual tool into the swivel head or set the parameter "Tool change" on the setup screenform "Rotary axes" to
"Automatic".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61233
[Channel %1: ] Block %2: Thread angle wrongly defined
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The thread angles were specified too large or too small.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check thread geometry.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61234
[Channel %1: ] Block %2: ShopMill subroutine %4 cannot be executed, as not tested by
ShopMill
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = Subroutine name
Explanation:
Before a ShopMill subroutine can be used, it has to be tested by ShopMill.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The subroutine first has to be simulated in ShopMill or loaded into the ShopMill operating mode "Machine auto".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
616
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61235
[Channel %1: ] Block %2: ShopTurn program %4 cannot be executed as not tested by ShopTurn.
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = Program name
Explanation:
Before a ShopTurn program can be executed, it has to be tested by ShopTurn.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
First simulate the program in ShopTurn or load it into the ShopTurn operating mode "Machine auto".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61236
[Channel %1: ] Block %2: ShopTurn subroutine %4 cannot be executed as not tested by
ShopTurn.
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = Subroutine name
Explanation:
Before a ShopTurn subroutine can be used, it has to be tested by ShopTurn.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Simulate the subroutine first in ShopTurn or load it into the ShopTurn operating mode "Machine auto".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61237
[Channel %1: ] Block %2: Retraction direction unknown. Withdraw tool manually!
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool is in the retraction area and it is unknown in which direction it can be travelled out of it.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Manually retract the tool from the retraction area defined in the program header and restart the program.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61238
[Channel %1: ] Block %2: Machining direction unknown!
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The direction of the next machining is unknown.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Please contact the responsible Siemens regional office.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
617
Cycle alarms
61239
[Channel %1: ] Block %2: Tool change point lies within retraction area!
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool change point has to be far enough outside the retraction area so that no tool extends into the retraction area when
the turret is swiveled.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Specify another tool change point.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61240
%[[Channel %1: ] Block %2: %]Wrong feed type
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The feed type is not possible for this machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check feed type
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61241
[Channel %1: ] Block %2: Retraction plane not defined for this machining direction
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No retraction plane has been defined for the selected machining direction.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Define the missing retraction plane.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61242
[Channel %1: ] Block %2: Wrong machine direction
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The machining direction has been specified incorrectly.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check the programmed machining direction.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
618
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61243
[Channel %1: ] Block %2: Correct tool change point, tool tip in retraction area!
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The tool change point must be situated so far outside the retraction area that no tool protrudes into the retraction area on
turret swivelling.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Specify another tool change point.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61244
[Channel %1: ] Block %2: Pitch change leads to undefined thread
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The specified pitch change causes a reversal of the thread direction.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check thread pitch change and thread geometry.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61245
[Channel %1: ] Block %2: Machining plane does not match modal machining plane
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Machining plane does not match modal one.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check the machining plane.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61246
[Channel %1: ] Block %2: Safety distance too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The safety clearance is too small for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase safety clearance.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
619
Cycle alarms
61247
[Channel %1: ] Block %2: Blank radius too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The blank radius is too small for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase blank radius.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61248
[Channel %1: ] Block %2: Infeed too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The infeed is too small for machining.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase infeed.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61249
[Channel %1: ] Block %2: Number of edges too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The number of edges is too small.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase number of edges.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61250
[Channel %1: ] Block %2: Width across flats/edge length too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The width across flats/edge length is too small.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase key width/edge length.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
620
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61251
[Channel %1: ] Block %2: Width across flats/edge length too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The width across flats/edge length is too large.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Decrease key width/edge length.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61252
[Channel %1: ] Block %2: Chamfer/radius too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Chamfer/radius is too large.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Decrease chamfer/radius.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61253
[Channel %1: ] Block %2: No finishing allowance programmed
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
No finishing allowance has been entered.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Programm a finishing allowance.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61254
[Channel %1: ] Block %2: Error while traveling to fixed stop
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Error on travelling to fixed stop.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
specify another Z1 position for gripping the counterspindle.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
621
Cycle alarms
61255
[Channel %1: ] Block %2: Error during cut-off: Tool broken?
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Cut-off could not be completed. A tool breakage might have occurred.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check the tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61256
[Channel %1: ] Block %2: Mirroring not allowed at program start. Deselect work offset!
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Mirroring impermissible at program start.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Deselect work offset.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61257
[Channel %1: ] Block %2: incomplete setup of counterspindle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Setup of the counterspindle is incomplete.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The following machine and setting data must be set for the counterspindle:
- MD52206 $MCS_AXIS_USAGE
- SD55232 $SCS_SUB_SPINDLE_REL_POS
- SD55550 $SCS_TURN_FIXED_STOP_DIST
- SD55551 $SCS_TURN_FIXED_STOP_FEED
- SD55552 $SCS_TURN_FIXED_STOP_FORCE
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61258
[Channel %1: ] Block %2: Assign parameters for counterspindle chuck in the spindle chuck
data
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The parameters for the counterspindle chuck in the spindle chuck data have not been assigned.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
622
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Remedy:
Indicate parameters ZCn, ZSn and ZEn in the screen "Parameters" > "Setting data" > "Spindle chuck data".
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61259
[Channel %1: ] Block %2: program contains new machining steps from ShopMill %4
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = ShopMill version
Explanation:
The program has been created with a ShopMill version that is higher than the existing one.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Delete the machining step and reprogram machining if required.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61260
[Channel %1: ] Block %2: program contains new machining steps from ShopTurn %4
Parameters:
%1 = Channel number
%2 = Block number, label
%4 = ShopTurn version
Explanation:
The program has been created with a ShopTurn version that is higher than the existing one.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Delete the machining step and reprogram machining if required.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61261
[Channel %1: ] Block %2: center offset too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The center offset on center drilling is larger than permissible.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Enter lower eccentricity ($SCS_DRILL_MID_MAX_ECCENT).
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61262
[Channel %1: ] Block %2: pitch not possible with selected tool
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The pitch of the tap does not match the programmed pitch.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
623
Cycle alarms
Remedy:
Use a tap with the programmed pitch.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61263
[Channel %1: ] Block %2: Chained ShopMill program blocks not permissible in subprogram on
pos. pattern
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
If a subroutine is called from a position pattern, the subroutine itself must not include a position pattern.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Reprogram machining.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61264
[Channel %1: ] Block %2: Chained ShopTurn program blocks not permissible in subprogram on
pos. pattern
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
If a subroutine is called from a position pattern, the subroutine itself must not include a position pattern.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Reprogram machining.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61265
[Channel %1: ] Block %2: Too many restrictions, use rectangular pocket
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
In face milling a maximum of only 3 sides can be delimited.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Use pocket cycle.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61266
[Channel %1: ] Block %2: Illegal machining direction
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
In face milling, the delimitations and the direction of machining do not match.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Alarms
624
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
Remedy:
Select another direction of machining.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61267
[Channel %1: ] Block %2: Plane infeed too large, residual corners remain
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
In face milling, the plane infeed must not exceed 85%.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select a smaller plane infeed, as otherwise residual corners will be left over.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61268
[Channel %1: ] Block %2: Illegal machining direction, residual corners are left over.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
In face milling, the machining direction does not match the selected delimitations.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
The machining direction must be selected to match the delimitations.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61269
[Channel %1: ] Block %2: External tool diameter too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Incorrect tool definition.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check angle and diameter of the tool used.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61270
%[[Channel %1: ] Block %2: %]Chamfer width too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Chamfer width selected too small.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase the chamfer width.
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
625
Cycle alarms
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61271
%[[Channel %1: ] Block %2: %]Chamfer width greater than tool radius
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Chamfer width larger than tool radius.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Use a larger tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61272
%[[Channel %1: ] Block %2: %]Insertion depth too small
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Insertion depth on chamfering too small.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Increase the insertion depth.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61273
%[[Channel %1: ] Block %2: %]Insertion depth too large
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Insertion depth on chamfering too large.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Decrease the insertion depth.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61274
%[[Channel %1: ] Block %2: %]Invalid tool angle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Invalid tool angle.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Check tool angle
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
626
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61275
[Channel %1: ] Block %2: Target point violates software limit switch!
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Due to a swivel action, the end point is outside the software limit switches.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select another retraction plane or approach a suitable interpolation point.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61276
[Channel %1: ] Block %2: External tool diameter required for restrictions
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Outer tool diameter required in case of delimitations.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Specify the outer tool diameter.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61277
[Channel %1: ] Block %2: Tool diameter larger than restriction
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Tool diameter larger than delimitation.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Use a smaller tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61278
[Channel %1: ] Block %2: If tool angle is larger than 90°, both tool diameters must be equal
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
For tool angles larger than 90°, the two tool diameters must be identical.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Correct the tool angle or the tool diameters.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
627
Cycle alarms
61279
[Channel %1: ] Block %2: If tool angle equals 90°, both tool diameters must be equal
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
For tool angles equal to 90°, the two tool diameters must be identical.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Correct the tool angle or the tool diameters.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61280
[Channel %1: ] Block %2: %4- Mirroring missing in work offset for counterspindle
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The work offset for counterspindle machining does not have Z mirroring.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Select Z mirroring for the work offset used.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61281
[Channel %1: ] Block %2: starting point of machining outside retraction planes
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The starting point of machining is outside the retraction planes.
It is derived from the programmed geometry plus the safety distance in the selected machining direction.
The calculated point must lie within the retraction area to ensure safe approach.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Adjust the retraction planes.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61282
[Channel %1: ] Block %2: end point of machining outside retraction planes
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The end point of machining is outside the retraction planes.
It is calculated internally (according to the selected machining strategy).
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Adjust the retraction planes.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
628
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
Cycle alarms
61283
[Channel %1: ] Block %2: direct approach not possible, as tool change required
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
After block search a position is to be reached by direct approach, but a tool change is required before.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
First execute a manual tool change, then restart the block search.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61284
[Channel %1: ] Block %2: starting point cannot be approached without collision. Pre-position
tool manually
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The starting point cannot be approached without collisions.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Preposition the tool manually.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61285
[Channel %1: ] Block %2: parking position is below return plane XRA.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
The parking position is below retraction plane XRA.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Move the parking position above retraction plane XRA.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
61286
[Channel %1: ] Block %2: machining not possible, check tool angle.
Parameters:
%1 = Channel number
%2 = Block number, label
Explanation:
Machining not possible with the specified tool.
Reaction:
Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.
Remedy:
Use a suitable tool.
Programm
Clear alarm with the RESET key. Restart part program
continuation:
Alarms
Diagnostics Manual, 10/2020, 6FC5398-6BP40-6BA4
629
|