Nissan Rogue. Manual - part 339

DLK-198

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

TOUCH SENSOR

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK TOUCH SENSOR LH GROND CIRCUIT

1. Disconnect automatic back door control module and touch sensor LH connector.

2. Check continuity between automatic back door control module harness connector and touch sensor LH

harness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TOUCH SENSOR LH GROND CIRCUIT 2

1. Connect automatic back door control module and touch sensor LH connector.

2. Check voltage between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK TOUCH SENSOR LH

Refer to 

DLK-199, "LH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace touch sensor LH. Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

Automatic back door control module

Touch sensor LH 

Continuity 

 Connector

Terminal

 Connector

Terminal

B55

2

D511

1

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

2

No

Automatic back door control module

Touch sensor LH

Continuity 

 Connector

Terminal

Connector

Terminal

B55

13

D511

2

Yes

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

13

No

(+)

(–)

Voltage

(Approx.)

Automatic back door control module

 Connector

Terminal

B55

13

Ground

0.01 – 0 V

2015 Rogue NAM

TOUCH SENSOR

DLK-199

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

LH : Component Inspection

INFOID:0000000011278931

1.

CHECK TOUCH SENSOR LH

1. Turn ignition switch OFF.

2. Disconnect touch sensor LH connector.

3. Check resistance between touch sensor LH terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace touch sensor LH. Refer to 

DLK-271, "TOUCH SENSOR : Removal and Installation"

.

Touch sensor LH

 Condition

Resistance 

(Approx.)

Terminal

1

2

Touch sensor LH

Detect obstruction

380 – 420 k

Ω

Other than above

0.95 – 1.05 k

Ω

2015 Rogue NAM

DLK-200

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SPINDLE MOTOR

SPINDLE MOTOR

RH
RH : Diagnosis Procedure

INFOID:0000000011278932

Regarding Wiring Diagram information, refer to 

DLK-90, "Wiring Diagram"

.

1.

CHECK SPINDLE MOTOR INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect spindle unit RH connector.

3. Check voltage between spindle unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace spindle unit RH. Refer to 

DLK-270, "SPINDLE UNIT : Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SPINDLE MOTOR CIRCUIT

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and spindle unit har-

ness connector. 

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

LH
LH : Diagnosis Procedure

INFOID:0000000011278933

Regarding Wiring Diagram information, refer to 

DLK-90, "Wiring Diagram"

.

1.

CHECK SPINDLE MOTOR INPUT SIGNAL

1. Turn ignition switch OFF.

(+)

(–)

Condition

Voltage

(Approx.)

Spindle unit RH

Connector

Terminal

B73

1

Ground

Back door

Auto open opera-

tion

Battery voltage

7

Auto close opera-

tion

Automatic back door control module

Spindle unit RH

Continuity 

Connector

Terminal

Connector

Terminal

B56

29

B73

1

Yes

36

7

Automatic back door control module

Ground

Continuity 

Connector

Terminal

B56

29

No

36

2015 Rogue NAM

SPINDLE MOTOR

DLK-201

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2. Disconnect spindle unit LH connector.

3. Check voltage between spindle unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace spindle unit LH. Refer to 

DLK-270, "SPINDLE UNIT : Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SPINDLE MOTOR CIRCUIT

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and spindle unit LH

harness connector. 

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(–)

Condition

Voltage

(Approx.)

Spindle unit LH

Connector

Terminal

B95

1

Ground

Back door

Auto open opera-

tion

Battery voltage

7

Auto close opera-

tion

Automatic back door control module

Spindle unit LH

Continuity 

Connector

Terminal

Connector

Terminal

B56

27

B95

1

Yes

34

7

Automatic back door control module

Ground

Continuity 

Connector

Terminal

B56

27

No

34

2015 Rogue NAM