Nissan Qashqai J11. Manual - part 242

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  240  241  242  243   ..

 

 

Nissan Qashqai J11. Manual - part 242

 

 

ECH-266

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P158A CPP SWITCH

3.

Check the continuity between clutch interlock switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK CLUTCH INTERLOCK SWITCH-2

1.

Adjust clutch interlock switch installation.

2.

Check the continuity between clutch interlock switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace clutch interlock switch.

Clutch interlock switch

Condition

Continuity

Terminals

1

 2

Clutch pedal

Fully released

Not existed

Fully depressed

Existed

Clutch interlock switch

Condition

Continuity

Connector

Terminals

1

 2

Clutch pedal

Fully released

Not existed

Fully depressed

Existed

P160C ECM

ECH-267

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

P160C ECM

DTC Logic

INFOID:0000000010379157

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

Turn ignition switch OFF and wait at least 12 minutes.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 1 second.

2.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECH-267, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010379158

1.

CHECK BATTERY TERMINALS

1.

Turn ignition switch ON.

2.

Turn ignition switch OFF and wait at least 12 minutes.

3.

Check the battery terminals for damage and looseness.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair malfunction(s) and GO TO 2.

2.

CHECK OTHER DTC-1

1.

Turn ignition switch ON.

2.

Check DTC.

Is DTC P160C displayed with P0130, P0136, P0217, P0226, P0420 or P2263?

YES

>> Perform the trouble diagnosis for DTC P0130, P0136, P0217, P0226, P0420 or P2263 and GO

TO 3. Refer to 

ECH-71, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK DTC

1.

Turn ignition switch OFF and wait at least 12 minutes.

2.

Turn ignition switch ON.

3.

Check DTC.

Is the DTC P160C displayed again?

YES

>> GO TO 4.

NO

>> GO TO 5.

4.

REPLACE ECM

1.

Replace ECM. Refer to 

ECH-313, "Removal and Installation"

.

2.

Proceed to 

ECH-103, "Work Procedure"

.

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P160C

CONTROL MODULE
(Control module)

ECM function is malfunctioning.

ECM

ECH-268

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P160C ECM

5.

CHECK OTHER DTC-2

1.

Start engine and let it idle for at least 1 minutes.

2.

Check DTC.

Is DTC P160C displayed with P0130, P0136, P0217, P0226, P0420 or P2263?

YES

>> Perform the trouble diagnosis for DTC P0130, P0136, P0217, P0226, P0420 or P2263 and GO

TO 3. Refer to 

ECH-71, "DTC Index"

.

NO

>> GO TO 6.

6.

CHECK RESULT OF PROCEDURE 2

Check result of procedure 2.

Is result of procedure 2 “YES”?

YES

>> GO TO 7.

NO

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

7.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Select “DATA MONITOR” mode with CONSULT.

2.

Drive the vehicle for at least 15 minutes at 0 - 50 km/h (0 - 31 MPH).

CAUTION:

Always drive vehicle at a safe speed.

3.

Check DTC.

Is DTC detected?

YES

>> Perform the trouble diagnosis for DTC P0130, P0136, P0217, P0226, P0420 or P2263 and GO

TO 3. Refer to 

ECH-71, "DTC Index"

.

NO

>> INSPECTION END

P1650 STARTER MOTOR RELAY 2

ECH-269

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

P1650 STARTER MOTOR RELAY 2

DTC Logic

INFOID:0000000010796370

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If the other DTC Confirmation Procedure is performed right before this procedure, the ignition switch must be
turned OFF and wait for 12 minutes or more to start this procedure.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-1

1.

Turn ignition switch OFF and wait at least 12 minutes.

2.

Turn ignition switch ON and wait at least 30 seconds

3.

Turn ignition switch OFF, wait at least 12 minutes and then turn ON.

4.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECH-269, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

1.

Start the engine and warm it up to normal operating temperature.

2.

Press start/stop OFF switch and check that the switch indicator is ON.

3.

Select “AUTO STOP START” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.

4.

Touch “START” and operate stop/start system. (engine stop.)

5.

Touch “CANCEL” and restart the engine.

Without CONSULT

Activate stop/start system. Refer to 

ECH-33, "STOP/START SYSTEM : System Description"

.

CAUTION:

Always drive vehicle at a safe speed.

Is stop/start system activated normal?

YES

>> INSPECTION END

NO

>> Proceed to 

ECH-269, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010500726

1.

CHECK ENGINE RESTART RELAY POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Remove engine restart relay.

3.

Turn ignition switch ON.

4.

Check the voltage between engine restart relay harness connector and ground.

DTC

Trouble diagnosis name

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P1650

STR MTR RELAY 2
(Engine restart relay cir-
cuit)

A

Engine restart relay is stuck ON.

• Starter control relay
• Engine restart relay

B

Engine restart relay is stuck OFF.

• Harness and connectors

(Between engine restart relay and starter motor 
harness is shorted to ground.)
(Between battery and engine restart relay har-
ness is open or shorted to ground.)

• IPDM  E/R
• Engine restart relay

 

 

 

 

 

 

 

Content   ..  240  241  242  243   ..