Mitsubishi Lancer Evolution X. Manual - part 292

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution X GS41EVO - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  290  291  292  293   ..

 

 

Mitsubishi Lancer Evolution X. Manual - part 292

 

 

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-233

DTC SET CONDITION
Logic Flow Chart

.

Check Conditions

• 2 seconds or more have passed since the engine 

starting sequence was completed.

• Heated oxygen sensor offset voltage is between 

0.4 and 0.6 volt.

Judgement Criterion

• Heated oxygen sensor (front) output voltage has 

continued to be 1.8 volts or higher for 2 seconds.

.

FAIL-SAFE AND BACKUP FUNCTION

• None

.

OBD-II DRIVE CYCLE PATTERN

Refer to Diagnosis Function − OBD-II Drive Cycle − 

Pattern 23 

P.13A-9

.

.

TROUBLESHOOTING HINTS (The most 
likely causes for this code to be set are:)

• Short circuit in heated oxygen sensor (front) out-

put line.

• Connector damage.
• ECM failed. 

End

Malfunction

No

No

No

2secs have passed?

Output voltage

> 1.8V

Good

AK604322

Start

Yes

Yes

Yes

Monitoring
conditions

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-234

DIAGNOSIS

STEP 1. Check harness connector C-34 at heated oxygen 
sensor (front) and harness connector B-09 at ECM for 
damage.
Q: Is the harness connector in good condition?

YES : Go to Step 2.
NO :  Repair or replace it. Refer to GROUP 00E, Harness 

Connector Inspection 

P.00E-2

. Then go to Step 3.

STEP 2. Check for short circuit to power supply between 
heated oxygen sensor (front) connector C-34 (terminal No. 
3) and ECM connector B-09 (terminal No. 38).
NOTE: Check harness after checking intermediate connector 
A-13. If intermediate connector is damaged, repair or replace it. 
Refer to GROUP 00E, Harness Connector Inspection 

P.00E-2

Then go to Step 3.
Q: Is the harness wire in good condition?

YES : Replace the ECM. When the ECM is replaced, 

register the ID code. Refer to GROUP 42B, ID Code 
Registration Necessity Judgment Table <Vehicles 
with KOS> 

P.42B-11

 or GROUP 42C, ID Codes 

Registration Judgment Table <Vehicles with WCM> 

P.42C-9

. Then go to Step 3.

NO :  Repair it. Then go to Step 3.

STEP 3. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to 

Diagnostic Function − OBD-II Drive Cycle − Pattern 23 

P.13A-9

.

(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0132 set?

YES : Retry the troubleshooting.
NO :  The inspection is complete.

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-235

DTC P0133: Heated Oxygen Sensor (front) Circuit Slow Responce

.

AK704249

1

2

3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

1 2
3 4

1

10 111213 14

19 20

2 3 4

7 8 9

2

8

7

6

5

4

3

11

21

20

19

18

17

16

15

14

13

12

9

22

1

10

0.5 V

AB

1

4

2

3

39

SKY BLUE

SKY BLUE

38

HEATED OXYGEN SENSOR (FRONT) CIRCUIT

B-09

C-34

6

RED

RED

7

A-13

HEATED OXYGEN SENSOR
(FRONT)

FROM MFI RELAY

TO ECM

ENGINE
CONTROL
MODULE

AK704229AB

Connector: A-13

A-13

AK704227

Connector: B-09

ECM

B-09 (GR)

AB

AK704228

AB

Heated oxygen
sensor (front)

Connector: C-34

C-34 (B)

SRS-ECU

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-236

CIRCUIT OPERATION

• A voltage corresponding to the oxygen concen-

tration in the exhaust gas is sent to the ECM (ter-
minal No. 38) from the output terminal (terminal 
No. 3) of the heated oxygen sensor (front).

• Terminal No. 4 of the heated oxygen sensor 

(front) is grounded with ECM (terminal No. 39).

• The ECM applies an offset voltage of 0.5 volt to 

terminal No. 4 of the heated oxygen sensor 
(front).

.

TECHNICAL DESCRIPTION

• The heated oxygen sensor (front) detects the 

concentration of oxygen in the exhaust gas; it 
converts those data to voltage, and inputs the 
resulting signals to the ECM.

• When the heated oxygen sensor (front) begins to 

deteriorate, the heated oxygen sensor signal 
response becomes poor.

• The ECM checks for the heated oxygen sensor 

(front) rich/lean switching frequency.

.

DESCRIPTIONS OF MONITOR METHODS

Heated oxygen sensor (front) rich/lean switching fre-

quency is under specified value.

.

MONITOR EXECUTION

Continuous

.

MONITOR EXECUTION CONDITIONS 
(Other monitor and Sensor)

Other Monitor (There is no temporary DTC stored 

in memory for the item monitored below)

• Heated oxygen sensor (front) heater monitor
• Misfire monitor
• Fuel system monitor
• Heated oxygen sensor (rear) feedback control 

system monitor

Sensor (The sensor below is determined to be 

normal)

• Mass airflow sensor
• Engine coolant temperature sensor
• Intake air temperature sensor
• Barometric pressure sensor
• Throttle position sensor
• Accelerator pedal position sensor

.

 

 

 

 

 

 

 

Content   ..  290  291  292  293   ..