Isuzu KB P190. Manual - part 977

Automatic Transmission – 4L60E – Electrical Diagnosis

Page 7C2–122

Action Taken When the DTC Sets

•

The TCM requests the ECM to illuminate the MIL during the second consecutive trip in which the conditions for
setting the DTC are met.

•

The TCM commands maximum line pressure.

•

The TCM freezes transmission adaptive functions.

•

The TCM inhibits TCC engagement.

•

At the time of the first failure, the TCM records the operating conditions when the conditions for setting the DTC are
met. The TCM stores this information as a Failure Record.

•

At the time of the second failure, the ECM records the operating conditions when the conditions for setting the DTC
are met. The ECM stores this information as a Freeze Frame.

•

The TCM stores either DTC U0073 or DTC U0100 in TCM history during the second consecutive trip in which the
conditions for setting the DTC are met.

Conditions for Clearing the DTC

•

The ECM turns off the MIL after the fourth consecutive drive trip in which the TCM does not send a MIL illumination
request.

•

Tech 2 can clear the DTC.

•

The TCM clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without a non-emission
related diagnostic fault occurring.

•

The TCM cancels the DTC default actions when the ignition is off long enough to power down the TCM.

Test Description

The following number refers to the step numbers in the diagnostic table:

The following tests are included in the Diagnostic System Check.

•

Tests the integrity of the GM LAN serial data communication circuit.

•

Tests for fault conditions on the vehicle immobiliser system stored in the ICU.

DTC P0864 and U0101 Diagnostic Table

Step Action

Yes

Has the Diagnostic System Check been performed?

Go to Step 2

Refer to

4.7 Diagnostic

System Check

Automatic Transmission – 4L60E – Electrical Diagnosis

Page 7C2–123

Step Action

Yes

Connect Tech 2 to the DLC.

Turn on the ignition, with the engine off.

N O T E

Before clearing the DTC, use the Tech

2 Freeze

Frame/Failure Record to record the transmission
parameters at the time the DTC set. Using Tech 2 to clear
the DTC(s) erases the Freeze Frame/Failure Record
records from the TCM.

On Tech 2 select:
Transmission / Automatic Transmission / Diagnostic
Trouble Codes / Freeze Frame.

Select the relevant DTC and note the parameters at the time of
the DTC setting.

On Tech 2 select:
Diagnostic Trouble Codes / Clear Engine & Transmission
DTCs.

Follow the instructions on Tech 2 and clear the DTCs.

Operate the vehicle within the conditions for running the DTC.

On Tech 2 select:
Diagnostic Trouble Codes / Read DTC Information.

Has either DTC PU0073 or DTC U0100 set?

Go to Step 3

Check for an

intermittent fault in

the circuit, refer to

8A Electrical-Body

and Chassis

Using Tech 2, attempt to communicate with the PIM.

Does the PIM failed to communicate?

Refer to the 6E1

Powertrain Interface

Module – V6

Go to Step 4

Are DTCs also set in the PIM?

Refer to 6E1

Powertrain Interface

Module – V6

Go to Step 5

Replace the TCM, refer to 7C4 Automatic Transmission – 4L60E –
On-vehicle Servicing.

Was the repair completed?

Go to Step 6

—

Using Tech 2, clear the DTCs.

Switch off the ignition for 30 seconds.

Start the engine.

Operate the vehicle within the conditions for running the DTC.

Does any of the serial data communication circuit – TCM DTCs fail
this ignition cycle?

Go to Step 2

Go to Step 78

Using Tech 2, select the DTC display function.

Does Tech 2 display any DTCs?

Go to the

appropriate DTC

Table

System OK

When all diagnosis and repairs are completed, check the system for correct operation.

Automatic Transmission – 4L60E – Electrical Diagnosis

Page 7C2–124

5 Electrical

Specifications

5.1

Transmission Fluid Temperature (TFT)
Sensor Specifications

Temperature

Minimum Resistance

Normal Resistance

Maximum Resistance

Signal

°C

Ω

Ω Volts

-40 90636

100707

110778 5.00

-30 47416

52684

57952 4.78

-20 25809

28677

31545 4.34

-10 14558

16176

17794 3.89

0 8481

9423

10365

3.45

10 5104 5671 6238 3.01

20 3164 3515 3867 2.56

30 2013 2237 2461 1.80

40 1313 1459 1605 1.10

50 876 973

1070

3.25

60 600 667 734 2.88

70 420 467 514 2.56

80 299 332 365 2.24

90 217 241 265 1.70

100 159 177 195 1.42

110 119 132 145 1.15

120 89.9 99.9 109.9 0.87

130 69.1 76.8 84.5 0.60

140 53.8 59.8 65.8 0.32

150 42.5 47.2 51.9 0.00

5.2 Range

Reference

Range Park

Reverse

Neutral

Gear

***

Shift

Solenoid A

(1-2 Shift

Solenoid)

ON*

OFF

ON OFF ON

OFF

Shift

Solenoid B

(2-3 Shift

Solenoid)

ON*

OFF

ON ON ON

2-4

Band -

- A - A - A - - A - A

Reverse

Input Clutch

- - - - - - - - - - -

Automatic Transmission – 4L60E – Electrical Diagnosis

Page 7C2–125

Range Park

Reverse

Neutral

Overrun

Clutch

- A A - - A A A A A

Forward

Clutch

A A A A A

Forward

Sprag Clutch

Assembly

H H H - H

H H H H H

3-4

Clutch -

- - A A - - A - - - -

Lo/Roller

Clutch

H - - - H

- - H - H

Lo/Rev

Clutch

- - - - - - - - - A

A = Applied

H = Holding

ON = Solenoid is energised

OFF = Solenoid is de-energised

* Shift solenoid state is a function of the vehicles speed and may change if the vehicle speed increases sufficiently

** Manual shift from second to first gear is electronically prevented under normal operating conditions

*** Manual shift from first to second gear is only available above approximately 48 – 56 km/h

5.3

Transmission Fluid Pressure Manual
Valve Position Switch Logic

Gear Selector Position

Signal A

Signal B

Signal C

Park/Neutral

Open 12 V

Closed 0 V

Open 12 V

Reverse

Closed 0 V

Open 12 V

Drive 4

Open 12 V

Closed 0 V

Drive 3

Open 12 V

Closed 0 V

Drive 2

Open 12 V

Drive 1

Closed 0 V

Open 12 V

Closed 0 V

Open 12 V

Closed 0 V

Invalid

Closed 0 V

5.4

Transmission Range Switch Logic

Gear Selector Position

Signal A

Signal B

Signal C

Signal P

Park (P)

Closed 0 V

Open 12 V

Closed 0 V

Reverse (R)

Closed 0 V

Open 12 V

Neutral (N)

Open 12 V

Closed 0 V

Open 12 V

Closed 0 V

Drive 4 (OD)

Open 12 V

Closed 0 V

Open 12 V

Drive 3 (3)

Closed 0 V

Drive 2 (2)

Closed 0 V

Open 12 V

Closed 0 V

Open 12 V

Drive 1 (1)

Open 12 V

Closed 0 V

Content .. 975 976 977 978 ..