Infiniti M35/M45 Y50. Manual - part 717

 

  Index      Infiniti     Infiniti M35/M45 Y50 - service repair manual 2007 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



  

 

Content   ..  715  716  717  718   ..

 

 

Infiniti M35/M45 Y50. Manual - part 717

 

 

DTC P2122, P2123 APP SENSOR

EC-1341

[VK45DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

6. 

CHECK APP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Check harness continuity between ECM terminal 106 and APP sensor terminal 3.
Refer to Wiring Diagram.

2.

Also check harness for short to ground and short to power.

OK or NG

OK

>> GO TO 8.

NG

>> GO TO 7.

7. 

DETECT MALFUNCTIONING PART

Check the following.

●

Harness connectors E108, M15

●

Harness for open or short between ECM and accelerator pedal position sensor

>> Repair open circuit or short to ground or short to power in harness or connectors.

8. 

CHECK APP SENSOR

Refer to 

EC-1341, "Component Inspection"

 .

OK or NG

OK

>> GO TO 10.

NG

>> GO TO 9.

9. 

REPLACE ACCELERATOR PEDAL ASSEMBLY

1.

Replace accelerator pedal assembly.

2.

Perform 

EC-788, "Accelerator Pedal Released Position Learning"

 .

3.

Perform 

EC-788, "Throttle Valve Closed Position Learning"

 .

4.

Perform 

EC-788, "Idle Air Volume Learning"

 .

>> INSPECTION END

10. 

CHECK INTERMITTENT INCIDENT

Refer to 

EC-857, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"

 .

>> INSPECTION END

Component Inspection

NBS005ON

ACCELERATOR PEDAL POSITION SENSOR

1.

Reconnect all harness connectors disconnected.

2.

Turn ignition switch ON.

3.

Check voltage between ECM terminals 106 (APP sensor 1 sig-
nal), 98 (APP sensor 2 signal) and ground under the following
conditions.

Continuity should exist.

Terminal

Accelerator pedal

Voltage

106
 (Accelerator pedal position 
sensor 1)

Fully released

0.4 - 1.1V

Fully depressed

3.7 - 4.8V

98
(Accelerator pedal position 
sensor 2)

Fully released

0.20 - 0.55V

Fully depressed

1.85 - 2.40V

MBIB0023E

EC-1342

[VK45DE]

DTC P2122, P2123 APP SENSOR

4.

If NG, replace accelerator pedal assembly and go to next step.

5.

Perform 

EC-788, "Accelerator Pedal Released Position Learning"

 .

6.

Perform 

EC-788, "Throttle Valve Closed Position Learning"

 .

7.

Perform 

EC-788, "Idle Air Volume Learning"

 .

Removal and Installation

NBS005OO

ACCELERATOR PEDAL

Refer to 

ACC-3, "ACCELERATOR CONTROL SYSTEM"

 .

DTC P2127, P2128 APP SENSOR

EC-1343

[VK45DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

DTC P2127, P2128 APP SENSOR

PFP:18002

Component Description

NBS005OP

The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometers which transform the accelerator pedal
position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of
the accelerator pedal and feed the voltage signals to the ECM. The
ECM judges the current opening angle of the accelerator pedal from
these signals and controls the throttle control motor based on these
signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine oper-
ation such as fuel cut.

CONSULT-II Reference Value in Data Monitor Mode

NBS005OQ

Specification data are reference values.

*: Accelerator pedal position sensor 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage.

On Board Diagnosis Logic

NBS005OR

These self-diagnoses have the one trip detection logic.

FAIL-SAFE MODE

When the malfunction is detected, ECM enters fail-safe mode and the MIL lights up.

PBIB1741E

MONITOR ITEM

CONDITION

SPECIFICATION

ACCEL SEN 1
ACCEL SEN 2*

●

Ignition switch: ON
(Engine stopped)

Accelerator pedal: Fully released

0.4 - 1.1V

Accelerator pedal: Fully depressed

3.7 - 4.8V

CLSD THL POS

●

Ignition switch: ON
(Engine stopped)

Accelerator pedal: Fully released

ON

Accelerator pedal: Slightly depressed

OFF

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P2127
2127

Accelerator pedal position 
sensor 2 circuit low input

An excessively low voltage from the APP 
sensor 2 is sent to ECM.

●

Harness or connectors
(APP sensor 2 circuit is open or shorted.)
(TP sensor circuit is shorted.)

●

Accelerator pedal position sensor
(APP sensor 2)

●

Electric throttle control actuator
(TP sensor 1 and 2)

P2128
2128

Accelerator pedal position 
sensor 2 circuit high input

An excessively high voltage from the APP 
sensor 2 is sent to ECM.

Engine operating condition in fail-safe mode

The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10 
degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
So, the acceleration will be poor. 

EC-1344

[VK45DE]

DTC P2127, P2128 APP SENSOR

DTC Confirmation Procedure

NBS005OS

NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V at idle.

 WITH CONSULT-II

1.

Turn ignition switch ON.

2.

Select “DATA MONITOR” mode with CONSULT-II.

3.

Start engine and let it idle for 1 second.

4.

If DTC is detected, go to 

EC-1346, "Diagnostic Procedure"

 .

 WITH GST

Follow the procedure “WITH CONSULT-II” above.

SEF058Y

 

 

 

 

 

 

 

Content   ..  715  716  717  718   ..