Infiniti G35 (V35) Sedan. Manual - part 1169

DIAGNOSIS SYSTEM (BCM)

SEC-31

< FUNCTION DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

ACTIVE TEST

Monitor Item

Condition

REQ SW-DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW-AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW-BD/TR

Indicates [ON/OFF] condition of trunk opener request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

CLUCH SW

Indicates [ON/OFF] condition of clutch switch.

BRAKE SW 1

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of P position.

SFT PN/N SW

Indicates [ON/OFF] condition of P or N position.

S/L -LOCK

Indicates [ON/OFF] condition of steering lock (LOCK).

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock (UNLOCK).

S/L RELAY-F/B

Indicates [ON/OFF] condition of ignition switch.

UNLK SEN-DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of P or N position.

SFT P -MET

Indicates [ON/OFF] condition of P position.

SFT N -MET

Indicates [ON/OFF] condition of N position.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock (LOCK).

S/L UNLOCK-IPDM

Indicates [ON/OFF] condition of steering lock (UNLOCK).

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status.

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical value start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

TRNK/HAT MNTR

Indicates [ON/OFF] condition of trunk lid.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.

SEC-32

< FUNCTION DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

THEFT ALM

THEFT ALM : CONSULT-III Function (BCM - THEFT)

INFOID:0000000000961330

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
Intelligent Key warning buzzer sounds when “ON” on CONSULT-III screen is touched.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT-III screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT-III screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT-III screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY IND ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp flashes when “KEY IND FSH” on CONSULT-III screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

LCD

This test is able to check meter display information
• Engine start information displays when “BRAKE/P” on CONSULT-III screen is touched.
• Engine start information displays when “BRAKE/P/ON” on CONSULT-III screen is touched.
• Key ID warning displays when “KEY ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “STLCK RELES” on CONSULT-III screen is touched.
• P position warning displays when “P RNG IND” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSERT KEY” on CONSULT-III screen is 

touched.

• Intelligent Key low battery warning displays when “KEY BAT LOW” on CONSULT-III screen is 

touched.

• Take away through window warning displays when “TK AWAY WDW” on CONSULT-III screen 

is touched.

• Take away warning display when “TAKE AWAY” on CONSULT-III screen is touched.
• OFF position warning display when “IGN OFF WARN” on CONSULT-III screen is touched.

TRUNK/GLASS HATCH

This test is able to check trunk lid opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.

FLASHER

This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.

IGN CONT2

This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.

P RANGE

This test is able to check A/T device power supply
A/T device power is supplied when “ON” on CONSULT-III screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.

LOCK INDCATOR

This test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

ACC INDCATOR

This test is able to check ACC indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

IGNITION ON IND

This test is able to check INGITION ON indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.

Test item

Description

Diagnosis mode

Function Description

WORK SUPPORT

Changes the setting for each system function.

DIAGNOSIS SYSTEM (BCM)

SEC-33

< FUNCTION DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

DATA MONITOR

WORK SUPPORT

ACTIVE TEST

IMMU

IMMU : CONSULT-III Function (BCM - IMMU)

INFOID:0000000000961331

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

Diagnosis mode

Function Description

Monitored Item

Description

REQ SW-DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW-AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW-BD/TR

Indicates [ON/OFF] condition of trunk opener request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch

UNLK SEN-DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

DOOR SW-DR

Indicates [ON/OFF] condition of front door switch LH.

DOOR SW-AS

Indicates [ON/OFF] condition of front door switch RH.

DOOR SW-RR

Indicates [ON/OFF] condition of rear door switch RH.

DOOR SW-RL

Indicates [ON/OFF] condition of rear door switch LH.

DOOR SW-BK

This is displayed even when it is not equipped.

CDL LOCK SW

Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.

CDL UNLOCK SW

Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.

KEY CYL LK-SW

Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.

KEY CYL UN-SW

Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch.

KEY CYL SW-TR

This is displayed even when it is not equipped.

TR/BD OPEN SW

Indicates [ON/OFF] condition of trunk lid opener switch.

TRNK/HAT MNTR

Indicates [ON/OFF] condition of trunk room lamp switch.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.

Test Item

Description

SECURITY ALARM SET

This mode is able to confirm and change security alarm ON-OFF setting.

THEFT ALM TRG

The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and 
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR” on 
CONSULT-III screen.

Test Item

Description

THEFT IND

This test is able to check security indicator lamp operation. The lamp will be turned on when “ON” 
on CONSULT-III screen is touched.

VEHICLE SECURITY HORN

This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.

HEADLAMP(HI)

This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5 
seconds after “ON” on CONSULT-III screen is touched.

FLASHER

This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activat-
ed after “ON” on CONSULT-III screen is touched.

SEC-34

< FUNCTION DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

DATA MONITOR

ACTIVE TEST

Diagnosis mode

Function Description

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

Monitor item 

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

TP 4

Indicates the number of ID which has been registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
The lamp will be turned on when “ON” on CONSULT-III screen touched.