Content .. 170 171 172 173 ..

Infiniti FX35, FX50 (S51). Manual - part 172

INSPECTION AND ADJUSTMENT

AV-461

< BASIC INSPECTION >

[NAVIGATION (TWIN MONITOR)]

CONFIGURATION (AV CONTROL UNIT) : Work Procedure

INFOID:0000000005474977

NOTE:
If “WRITE CONFIGURATION” is unsuccessful, perform “Accessory Number Initialization”. For details, refer to

AV-382, "On Board Diagnosis Function"

After performing “Accessory Number Initialization”, reboot the AV control unit to perform “WRITE CONFIGU-
RATION”.

WRITING MODE SELECTION

CONSULT-III Configuration

Select “CONFIGURATION” of “MULTI AV”.

When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.

PERFORM “WRITE CONFIGURATION-CONFIG FILE”

CONSULT-III Configuration

Perform “WRITE CONFIGURATION-Config file”.

>> WORK END

PERFORM “WRITE CONFIGURATION-MANUAL SELECTION”

CONSULT-III Configuration

Select “WRITE CONFIGURATION-Manual selection” to write vehicle specifications into the AV control unit.
For data to write, refer to

AV-461, "CONFIGURATION (AV CONTROL UNIT) : Configuration List"

>> GO TO 4.

OPERATION CHECK

Check that the operation of the AV control unit and camera images (fixed guide lines and predictive course
lines) are normal.

>> WORK END

CONFIGURATION (AV CONTROL UNIT) : Configuration List

INFOID:0000000005474978

CAUTION:

Check vehicle specifications before servicing.

Function

Description

READ CONFIGURATION

• Reads the vehicle configuration of current AV control unit.
• Saves the read vehicle configuration.

WRITE CONFIGURATION-Manual selection

Writes the vehicle configuration with manual selection.

WRITE CONFIGURATION-Config file

Writes the vehicle configuration with saved data.

MANUAL SETTING ITEM

Items

Setting value

STEERING

LHD

RHD

CAMERA SYSTEM

NONE/AVM

REAR CAMERA

REAR+SIDE

SOUND SYSTEM

BASE

BOSE

AV-462

< BASIC INSPECTION >

[NAVIGATION (TWIN MONITOR)]

INSPECTION AND ADJUSTMENT

NOTE:
AVM: Around view monitor

PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT

PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Description

INFOID:0000000005527061

Adjust the center position of the predictive course line of the rear view monitor if it is shifted.

PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure

INFOID:0000000005527062

DRIVING

Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.

>> END

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description

INFOID:0000000005474981

• Perform the calibration and perform the writing to the around view monitor control unit when removing and

replacing each camera, removing the camera mounting parts (front grille, door mirror, etc.) and replacing the
around view monitor control unit.

• Align the white lines on the road near the vehicle at the boundary of each camera image by this camera cal-

ibration. The white lines far from the vehicle may not be aligned at the boundary of each camera image. The
farther the line, the greater the difference is.

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure

INFOID:0000000005474982

Calibration flowchart

Following the flowchart shown in the figure, perform the calibration.

NOTE:

JPNIA1341GB

INSPECTION AND ADJUSTMENT

AV-463

< BASIC INSPECTION >

[NAVIGATION (TWIN MONITOR)]

In the un-match display, the un-match camera position is indicated
as “

” on the birds-eye view.

Calibration procedure

AROUND VIEW MONITOR SCREEN CONFIRMATION

Check that there is the un-match display in any camera.
Is the un-match display visible?

YES

>> GO TO 2.

>> GO TO 4.

CHECK THAT AROUND VIEW MONITOR CONTROL UNIT IS REPLACED

Check that the around view monitor control unit is replaced.
Is the around view monitor control unit replaced?

YES

>> GO TO 3.

>> GO TO 5.

RELEASE UN-MATCH DISPLAY (PERFORM ONLY WHEN THE AROUND VIEW MONITOR CONTROL

UNIT IS REPLACED)

Select “Camera Cont.” of Confirmation/ Adjustment mode, and then set to “Calibrating Camera Image”
mode.

Press the “ENTER” switch of the multifunction switch on each
screen of “Rear Camera”, “Front Camera”, “Dr-Side Camera”,
“Pass-Side Camera”.

CAUTION:

• Do never operate the center dial and up/down/left/right

switches. Only press the “ENTER” switch.

• Never perform “Initialize Camera Image Calibration”.

Display the around view monitor screen, and check that there is
no malfunction such as a difference between each camera
image.

Is there a malfunction?

YES

>> Calibration end

>> GO TO 1.

PERFORM SIMPLIFIED CONFIRMATION/ADJUSTMENT BY “FINE TUNING OF BIRDS-EYE VIEW”

Put target line 1 on the ground beside each axle using packing tape, etc.

Put target lines 2 equal to the vehicle total length + approximately 1.0 m (39.3 in) from the vehicle side
(right and left) at approximately 30 cm (11.8 in) away from the vehicle (make the line as parallel with the
vehicle as possible)

JSNIA2378ZZ

JSNIA2379ZZ

AV-464

< BASIC INSPECTION >

[NAVIGATION (TWIN MONITOR)]

INSPECTION AND ADJUSTMENT

Preparation of simplified target line

Select “Camera Cont.” of Confirmation/ Adjustment mode, and then set to “Fine Tuning of Birds-Eye View”
mode.

Select left and right cameras by pressing the “CAMERA” switch, and perform the following confirmation.

Check that target line 1 is aligned with the marker on the screen. Overlap the line aligned to the marker
with the upper/lower switches if necessary.

Check if there is a difference between target lines 2 between cameras. Adjust target lines 2 to be straight
lines by operating the center dial and left/right switches if necessary.

CAUTION:

•

Never adjust the front camera and rear camera. Only adjust the right and left cameras.

•

Operate the center dial slowly because the changing of the screen takes approximately 1 sec-
ond.

Simplified target line adjustment method

Adjust left and right cameras. Check that the difference between target line 1 and the marker on the
screen, and between target lines 2 is solved.
NOTE:
• It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration” of

“Calibrating Camera Image”.

JSNIA0927ZZ

Target lines 1

Target lines 2

Approx. 30 cm (11.8 in)

Approx. 1.0 m (39.3 in)

JSNIA0929ZZ

Target lines 1

Target lines 2

Marker for target line 1

Boundary between cameras

Crosshairs cursor (mark indicated
the selected camera)

Adjustment method for target lines 1
(right)

Adjustment method for target lines 2
(right)

Content .. 170 171 172 173 ..