333

6

Install the headrest;

7

Install the front seat with 4 tightening bolts. Torque: 14.72~23.52N.m.

3.Adjust

1

The seat can adjust tilt angle forward in torque 2° x 5=10°;

Adjust backwards 2° x 27=54°;

2

The seat assembly slides forwards 15mm x 4=60mm in torque 15N.m;

Slide backwards 15mm x 10=150mm;

3

The headrest can be adjusted in 3 positions in height.

Rear Seat

1.Rear seat back

1

Removal

a. Lift the rear seat back lock handle upwards. Turn seat back down forwards. Remove 4 set bolts.

Remove seat backassembly from the vehicle;

b. Remove seat back lock handle and handle seat;

Install Front and Rear Seat Snap Ring

Install Headrest Support

Track Assembly 

Adjuster Assembly

Install Adjuster and Track Assembly

Assemble the Seatback and Cushion

334

c.

Remove the snap ring from the rear seat back. Open the seat back cover. Remove the inside snap

ring. Remove the seat cover.

2

Re-assembly

a. Install the snap ring at the inside of the seat back;

b. Install the snap ring at the rear seat back;

c. Install the seat back lock handle seat to the rear seat back;

d. Install the rear trunk carpet to the rear seat back with 10 clips;

e. Install the rear seat back assembly to the vehicle with 4 bolts. Tighten bolt torque: 3.92~6.86N.m.

2.Rear seat cushion assembly

1

Removal

a. First remove therear seat back;

b. Lift the front of the seat cushion. Disconnet the seat cushion from the clamp on the floor, push

backwards, separate it from the hook. Remove seat cushionassembly from the vehicle;

c. Remove the snap ring on the seat cushion;

d. Remove the snap ring in the cover. Remove cover.

e. Remove the clamp under the seat cushion;

2

Re-assembly

The installation is in the reverse order of the removal.

Remove Rear Seatback Assembly

Seatback Lock handle

Handle Seat

Remove Seatback Set Bolt

Remove Seatback Cover

Remove Seatback Handle and Seat

335

(VII) Seat Belt

The vehicle seat belt is compulsory for drivers and passengers for safety purpose. It is the facility to prevent

the passengers from being hurt or reduce the possibility of being hurt when the vehicle is in emergent drive or

traffic accident occurs. Ck-1 front seat adopts Three Points Emergency Lock Retractor Pretension Seat

Belt , It is composed of retractor assembly, belt buckle assembly and height adjuster assembly.

1. Height Adjuster Assembly

2.  Retractor Assembly

3. Belt Buckle Assembly  4.anchorage

1. Belt Buckle

Belt buckle is enclosure type, See Figure

Replacement Of The Seat Belt Buckle

(1) Remove the seat adjuster hinge cover;

(2) Remove the bolt from the belt buckle on the seat side;

(3) Remove the seat belt buckle from the seat;

(4) Replace the seat belt buckle.

4

1

2

3

336

2. Retractor

The retractor is pre-tensioner. The retractor will pre-tension the seat belt when something emergency hap-

pens to prevent passengers from being hurt. It can sense the vehicle acceleration and the acceleration of the

belt being pulled out.

The retractor belt can be pull out and drawn back freely. It will not be locked at 12° around the safety

position, but locked at over 27°. The passenger can move in small area. The pre-tensioner will transmit within

5ms~10ms when something emergency happens to tension and lock the belt.

Notice:

1. Check the product for damage, crack and rust before installation.

2. Put the retractor vertically and the belt can be pulled out. Check if the belt can be pulled out

and around. Check if the retractor works.

3. When installing the pretensioned seat belt, check the transmittor head pin for slant and rust.

The transmitter in the pretensioned seat belt can be used for 15 years after installation.

4. Check if the belt buckle and the attachment matches the connecting mode of the to-be-installed

vehicle module. Check if the opening of the buckle is flexible.

5. See if the screw thread of the nut welded on the cover is clear when installing the bolt. Assemble

the bolt after clearing the welding residue if there is any.

6. When the retractor belt is pulled out, there should be no obstacles around the belt (such as,

wire harness ect) , Remove the obstacles and make sure the retractor and the belt will not be

scratched.

3.Front seat belt removal/installation

Warning:

Do not remove retractor.

(1) Turn the ignition switch to LOCK.

(2) Disconnect the negative (--) terminal cable from the battery

for 1min.

(3) Remove B- pillar lower frame.

(4) Pry the seat belt which is used to install the tension wheal.

Use a screwdriver to pry off the stop plate of the seat

belt connector with tensioner.

(5) Disconnect the seat belt connector with tensioner.

Remove 2 set bolts on the hang ring and remove the hang

ring.

(6) Remove two set bolts in the retractor and remove the

front seat belt.

(7) The installation is in the reverse order of the removal.

Stop Plate

Bolt

Front Seat Belt

Screw

Bolt

Lid