329

(V) Rear Bumper

The structure diagram is shown as the figure below:

1.Cross Pan Head Tapping Screw And Big Washer Set

2.Cross Pan Head Screw (GB973 M6X16)

3.Cross Pan Head Screw (GB973 M6X16) 4.Rear Bumper

5.Clip

6.Rear Bumper Reinforce-

ment Assembly

7.Rear Bumper Mounting Bracket Assembly

8.Hexigon Bolt and Spring Washer

Set  9.Hexigon Bolt Spring and Flat Gasket Set

1.Rear Bumper Removal/Installation

(1) Disconnect the negative (--) terminal cable from the battery.

(2) Remove the cross pan head tapping screw and big washer set.

(3) Remove 4 hexagon bolt on the mounting bracket.

(4) Remove 2 cross pan head screw (GB973 M6X16)

(5) Pull the rear bumper out from the body.

(6) Remove the cross pan head screw (GB973 M6X16) and hexagon bolt spring and flat gasketset. Remove

the rear bumper mounting bracket assembly.

(7) The installation is in the reverse order of the removal.

330

2.Notice On Removing The Rear Bumper

(1) Pull the rear bumper out to separate it from the bumper rail.

Warning

If only one side of the rear bumper is separated from the bumper rail, the bumper may drop and
result in body injury. Be careful not to make the bumper drop before separating the rear bumper
from the bumper rail.

3.Notice On Installing The Rear Bumper

(1) Press the rear bumper joint into the vehicle body to connect the rear bumper mounting bracket assembly

and the bumper rail.

(2) Insert the rear bumper end tab into the corresponding hole of the rear fender to flush with the outer

surface.

331

(VI) Seat Removal, Installation and Adjustment

Front Seat

See Figure

Disassembly of Front Seat

1.Headrest Assembly

2. Headrest Support

3.Snap Ring

4.Front Seat Backassembly

5.Front Seat Back Cover

6.Cap Nut

7.Front Seat Coupling Plastic Gasket

8.Track Assembly

9.Front Seat Cushion Cover

10.Front Seat Cushion Assembly

11.Adjuster Assembly

12.Adjuster Hinge Cover

1. Removal

1

Remove 4 bolts and the seat from the vehicle;

2

Turn the headrest lock handle to"Non-LOCK". Remove headrest and bracket;

3

Remove the attaching screw, Remove adjuster hinge cover from the front seat;

4

Remove the 4 snap ring under the rear side of the seat back. Remove the set bolt and nut at the both side

of the seat back;

5

Remove seat coupling plastic gasket;

6

Remove the seat cushion, track assembly and adjuster assembly;

7

Press the headrest support and push it upwards by hand in the direction as the Figure shows and remove

the headrest support;

8

Open the seat backcover. Remove the inner coversnap ring. Remove the seat backcover;

332

9

Remove the snap ring under the seat cushion. Open the front seat cushion cover. Remove the inner

coversnap ring. Remove the seat cushion cover.

2. Installation

1

Install snap ring at the front and rear seat. Be careful not to foul the cover or get it wrinkled;

2

Install the snap ring at the front of the seat back. Install the front seat headrest support;

3

Install the adjuster and track assembly with bolts;

4

Install the coupling plastic gasket. Install the seat back assembly to the seat cushion with bolts and nuts.

Install the snap ring to the rear seat back;

5

Install the adjuster hinge cover with 2 screws;

Remove the Headrest and Bracket

Remove the Front Seat Adjuster Hinge Cover

Remove the Seatback Snap Ring and Set Bolt

Track Assembly

Adjuster Assembly

Remove the Track and Adjuster Assembly 

Remove the Headrest Support

Remove the Seatback Cover

Remove bolts

Non-LOCK