Porshe 911 (997). Manual - part 1213

Processing nozzle

ATTENTION

→ Observe the safety instructions of the individual adhesive set components.

Note

In addition to this manual, observe the relevant job descriptions for body repairs!

• 

Note

In addition to this manual, observe the relevant job descriptions for body repairs!

• 

Releasing holder

1. Open

holder.

1.1. Release holder -arrow- and fold up.

Pressing sliding lock

2. Press sliding lock upwards

2.1. Press sliding lock upwards in direction of arrow -arrow- .

Diagnostic system: reading out fault memory and activating systems

Processing nozzle

5009

3. Insert piston

rod.

3.1. Hold sliding lock pressed and insert piston rod -B1- completely into the gun grip -B1- .

Inserting piston rod

Inserting cartridge

4. Insert mixing cartridge.

4.1. Insert double cartridge -C1- into the gun -B- from above. Insert the cartridge until the muzzle of the gun

engages in the groove of the cartridge.

5. Engage

holder.

5.1. Swivel holder downward and engage on handle of gun.

Engaging holder

Diagnostic system: reading out fault memory and activating systems

Processing nozzle

5010

Opening cartridge

6. Open

cartridge.

6.1. Turn screw cap 90 ° counter-clockwise and remove.

7. Squeeze adhesive to the front.

7.1. By activating the valve of the gun grip, allow the piston rod to move out slowly until both components

emerge equally.

7.2. Wipe off any adhesive that emerges.

Fitting processing nozzle

8. Fit processing nozzle.

8.1. Before fitting the processing nozzle, ensure that the muzzle -A- and the mixing channels are aligned on

one level, if necessary turn the bayonet locking mechanism on the processing nozzle through 90°.

8.2. Position processing nozzle -C2- and turn clockwise 90°.

9. Mix adhesive components.

9.1. By activating the valve of the gun grip, allow the piston rod to move out slowly until the adhesive is

visible in the processing pipe.

Diagnostic system: reading out fault memory and activating systems

Processing nozzle

5011

Working time of structural adhesive

10. Bond the body part.

Note

In order to ensure that the substance is completely mixed, apply a 30 mm long adhesive bead of fresh
adhesive to a piece of cardboard before processing.

• 

Process the adhesive within the processing period. The adhesive must be applied and the body part
must be jointed within this period. Any resistance welding to be carried out in the area of the bonding
must be performed within this period as well. → Working time: 60 min

• 

Do not load bonded parts until hardening is complete!

• 

If the contents of the cartridge are not used up completely, the processing nozzle must be kept on the
cartridge until the adhesive hardens. In the event of later processing, a new processing nozzle must be
used.

• 

10.1.

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321, 997410, 997411, 997430, 997431,
997610, 997611, 997620, 997621

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

Diagnostic system: reading out fault memory and activating systems

Processing nozzle

5012