Porshe 911 (997). Manual - part 1148

Gas welding

Gas welding

A

- Brazing

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321, 997410, 997411, 997430, 997431,
997610, 997611, 997620, 997621

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

Diagnostic system: reading out fault memory and activating systems

Gas welding

4749

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Gas welding

4750

- Re-imprinting new vehicle identification number

Tools

Designation

Type

Number Explanation

Handschlagstempel

special tool

96930

8 mm letter/digit embossing
tool with DIN 1451 closely
spaced lettering, letter set

commercially
available tool

NR.128-1

Re-imprinting new vehicle identification number

Vehicle identification number

After replacing the body or the sheetmetal parts in the area of the vehicle identification number (firewall), the
original vehicle identification number must be reimprinted onto the new body or the new sheet metal part.
The documentation of the imprinted vehicle identification number in the vehicle supplementary document or
legally permissible treatment can be obtained from the importer of the respective country.
An incorrectly imprinted (stamped) vehicle identification number should be permanently crossed through with
a X so that it remains legible. The vehicle identification number to be newly imprinted should be imprinted
above the crossed through identification number.

Spacer for replacing the vehicle identification number

The spacer for applying the vehicle identification number is in the front, right firewall. Two sections are
intended for use.

4751

–  Section 1 -A- is the standard spacer.

Vehicle identification number

–  Section 2 -B- is the spare spacer for a corrected vehicle identification number.

Re-imprinting new vehicle identification number

Note

Only imprint vehicle identification number in a cathodic-dip coated sheetmetal part.  )

• 

The area should be countered when imprinting the vehicle identification number.

• 

1. Stamp the vehicle identificaiton number to be replaced with  8 mm letter/digit embossing tool with DIN

1451 closely spaced lettering, letter set NR.128-1

 and the Porsche star Handschlagstempel 96930 in

den Platzhalter einschlagen.

2. Mask imprinted vehicle identification

number.

3. Apply exterior paintwork.

4. Remove the vehicle identification number mark.

5. Paint repair area with clear

lacquer.

1) Cathodic-dip coating is the primer applied to the sheetmetal parts at the factory

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321, 997410, 997411, 997430, 997431,
997610, 997611, 997620, 997621

Diagnostic system: reading out fault memory and activating systems

Spacer for replacing the vehicle identification number

4752