Porshe 911 (997). Manual - part 1038

Disengaging wiring harness

2. Disengage retaining clips with wiring harness on centre console and remove the

harness.

Installing wiring harness for centre console

Note

The wire harness for centre console spare parts scope means the scope for fully-equipped vehicles. Depending
on the vehicle equipment, connectors not required are tied to the wire harness for centre console using
tie-wraps.
When doing this, ensure the lines are routed correctly so that no line becomes trapped or damaged.

Laying wiring harness

1. Lay wiring harness with retaining clips in centre console and push on retaining clips at the points

provided.

2. Push electric connectors onto equipment versions until they are felt to engage.

Diagnostic system: reading out fault memory and activating systems

Removing wiring harness for centre console

4309

Subsequent work

Subsequent work for interior monitoring sensor

Install centre console. → 681719 Removing and installing centre console - chapter on "Installing"

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321, 997410, 997411, 997430, 997431,
997610, 997611, 997620, 997621

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

•

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

•

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

•

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

•

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Diagnostic system: reading out fault memory and activating systems

Subsequent work

4310

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

•

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

•

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

•

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

•

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

•

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

•

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work for interior monitoring sensor

4311

- Preliminary work
- Removing rear wire harness
- Installing rear wire harness
- Subsequent work

Tools

Designation

Type

Number

Explanation

Disassembly tool,
universal

commercially
available tool

NR.21

Preliminary work

1. Disconnect battery. → 271000 Work instructions after disconnecting the battery

2. Remove front seat at left and right. → 720119 Removing and installing front seat - section on

"Removing" [997310 997320 997610 997620]→ 720119 Removing and installing front seat - section on
"Removing" [997311 997321 997611 997621]

3. Remove left and right scuff plate. → 680519 Removing and installing inner door sill trim - section on

"Removing"

4. Remove rear side trim panel at left and right. → 707519 Removing and installing rear side trim panel -

section on "Removing"

Note

Only in the coupé.

5. Remove C-pillar trim panel. → 706819 21 Removing and installing C-pillar trim panel - section on

"Removing"

6. Removing rear wall trim panel → 703119 Removing and installing trim panel for rear wall - section on

"Removing" [997310 997311 997320 997321]→ 703119 21 Removing and installing trim panel for rear
wall - section on "Removing" [997610 997611 997620 997621]

4312

Content .. 1036 1037 1038 1039 ..