Toyota Corolla Hybrid (2020 year). Owner's manual - part 13

198

4-5. Using the driving support systems

Select a distance from the table 
below. Note that the distances 
shown correspond to a vehicle 
speed of 50 mph (80 km/h). 
Vehicle-to-vehicle distance 
increases/decreases in accor-
dance with vehicle speed. When 
the vehicle is stopped by system 
control, the vehicle stops at a 
certain vehicle-to-vehicle dis-
tance depending on the situa-
tion.

After the vehicle ahead of you 
starts off, press the “+RES” 
switch.
Your vehicle will also resume 
follow-up cruising if the acceler-

ator pedal is depressed after the 
vehicle ahead of you starts off.

1

Pressing the cancel switch 
cancels the speed control.

The speed control is also canceled 
when the brake pedal is depressed. 
(When the vehicle has been 
stopped by system control, 
depressing the brake pedal does 
not cancel the setting.)

2

Pressing the “+RES” switch 
resumes the cruise control 
and returns vehicle speed to 
the set speed.

When your vehicle is too close 

Vehicle-to-vehicle dis-
tance settings (vehi-
cle-to-vehicle distance 
control mode)

Distance 

options

Vehicle-to-vehicle dis-

tance

Long

Approximately 160 ft. 

(50 m)

Medium

Approximately 130 ft. 

(40 m)

Short

Approximately 100 ft. 

(30 m)

Resuming follow-up 
cruising when the vehicle 
has been stopped by sys-
tem control (vehi-
cle-to-vehicle distance 
control mode)

Canceling and resuming 
the speed control

Approach warning (vehi-
cle-to-vehicle distance 
control mode)

199

4-5. Using the driving support systems

4

Dr

iv

ing

to a vehicle ahead, and suffi-
cient automatic deceleration via 
the cruise control is not possi-
ble, the display will flash and the 
buzzer will sound to alert the 
driver. An example of this would 
be if another driver cuts in front 
of you while you are following a 
vehicle. Depress the brake 
pedal to ensure an appropriate 
vehicle-to-vehicle distance.

■

Warnings may not occur 
when

In the following instances, warn-
ings may not occur even when 
the vehicle-to-vehicle distance is 
small.


When the speed of the pre-
ceding vehicle matches or 
exceeds your vehicle speed



When the preceding vehicle is 
traveling at an extremely slow 
speed



Immediately after the cruise 
control speed was set



When depressing the acceler-
ator pedal

When constant speed control 
mode is selected, your vehicle 
will maintain a set speed without 
controlling the vehicle-to-vehi-
cle distance. Select this mode 
only when vehicle-to-vehicle dis-
tance control mode does not 
function correctly due to a dirty 
radar, etc.

1

With the cruise control off, 
press and hold the cruise 
control main switch for 1.5 
seconds or more.

Immediately after the switch is 

pressed, the dynamic radar cruise 

control indicator will come on. After-

wards, it switches to the cruise con-

trol indicator.
Switching to constant speed control 

mode is only possible when operat-

ing the switch with the cruise con-

trol off.

2

Accelerate or decelerate, 
with accelerator pedal opera-
tion, to the desired vehicle 
speed (at or above approxi-
mately 20 mph [30 km/h]) 
and press the “-SET” switch 
to set the speed.

Cruise control “SET” indicator will 

Selecting constant speed 
control mode

200

4-5. Using the driving support systems

come on.
The vehicle speed at the moment 

the switch is released becomes the 

set speed.
Adjusting the speed setting: 

P.196
Canceling and resuming the speed 

setting: P.198

■

Dynamic radar cruise control 

with full-speed range can be set 

when

●

The shift lever is in D.

●

The desired set speed can be set 

when the vehicle speed is approx-

imately 20 mph (30 km/h) or more. 

(However, when the vehicle speed 

is set while driving at below 

approximately 20 mph [30 km/h], 

the set speed will be set to 

approximately 20 mph [30 km/h].)

■

Accelerating after setting the 

vehicle speed

The vehicle can accelerate by oper-

ating the accelerator pedal. After 

accelerating, the set speed 

resumes. However, during vehi-

cle-to-vehicle distance control 

mode, the vehicle speed may 

decrease below the set speed in 

order to maintain the distance to the 

preceding vehicle.

■

When the vehicle stops while 

follow-up cruising

●

Pressing the “+RES” switch while 

the vehicle ahead stops will 

resume follow-up cruising if the 

vehicle ahead starts off within 

approximately 3 seconds after the 

switch is pressed.

●

If the vehicle ahead starts off 

within 3 seconds after your vehicle 

stops, follow-up cruising will be 

resumed.

■

Automatic cancelation of vehi-

cle-to-vehicle distance control 

mode

Vehicle-to-vehicle distance control 

mode is automatically canceled in 

the following situations.

●

VSC is activated.

●

TRAC is activated for a period of 

time.

●

When the VSC or TRAC system is 

turned off.

●

The sensor cannot detect cor-

rectly because it is covered in 

some way.

●

Pre-collision braking is activated.

●

The parking brake is operated.

●

The vehicle is stopped by system 

control on a steep incline.

●

The following are detected when 

the vehicle has been stopped by 

system control:

• The driver is not wearing a seat 

belt.

• The driver’s door is opened.

• The vehicle has been stopped for 

about 3 minutes

If vehicle-to-vehicle distance control 

mode is automatically canceled for 

any reasons other than the above, 

there may be a malfunction in the 

system. Contact your Toyota dealer.

■

Automatic cancelation of con-

stant speed control mode

Constant speed control mode is 

automatically canceled in the follow-

ing situations:

●

Actual vehicle speed is more than 

approximately 10 mph (16 km/h) 

below the set vehicle speed.

●

Actual vehicle speed falls below 

approximately 20 mph (30 km/h).

201

4-5. Using the driving support systems

4

Dr

iv

ing

●

VSC is activated.

●

TRAC is activated for a period of 

time.

●

When the VSC or TRAC system is 

turned off.

●

Pre-collision braking is activated.

If constant speed control mode is 

automatically canceled for any rea-

sons other than the above, there 

may be a malfunction in the system. 

Contact your Toyota dealer.

■

Brake operation

A brake operation sound may be 

heard and the brake pedal response 

may change, but these are not mal-

functions.

■

Warning messages and buzzers 

for dynamic radar cruise con-

trol with full-speed range

Warning messages and buzzers are 

used to indicate a system malfunc-

tion or to inform the driver of the 

need for caution while driving. If a 

warning message is shown on the 

multi-information display, read the 

message and follow the instructions. 

(P.172, 459)

■

When the sensor may not be 

correctly detecting the vehicle 

ahead

In the case of the following and 

depending on the conditions, oper-

ate the brake pedal when decelera-

tion of the system is insufficient or 

operate the accelerator pedal when 

acceleration is required.
As the sensor may not be able to 

correctly detect these types of vehi-

cles, the approach warning 

(P.198) may not be activated.

●

Vehicles that cut in suddenly

●

Vehicles traveling at low speeds

●

Vehicles that are not moving in the 

same lane

●

Vehicles with small rear ends 

(trailers with no load on board, 

etc.)

●

Motorcycles traveling in the same 

lane

●

When water or snow thrown up by 

the surrounding vehicles hinders 

the detecting of the sensor

●

When your vehicle is pointing 

upwards (caused by a heavy load 

in the luggage compartment, etc.)

●

Preceding vehicle has an 

extremely high ground clearance

■

Conditions under which the 

vehicle-to-vehicle distance con-

trol mode may not function cor-

rectly

In the case of the following condi-

tions, operate the brake pedal (or 

accelerator pedal, depending on the 

situation) as necessary.
As the sensor may not be able to 

correctly detect vehicles ahead, the 

system may not operate properly.

●

When the road curves or when the 

lanes are narrow

202

4-5. Using the driving support systems

●

When steering wheel operation or 

your position in the lane is unsta-

ble

●

When the vehicle ahead of you 

decelerates suddenly

●

When driving on a road sur-

rounded by a structure, such as in 

a tunnel or on a bridge

●

While the vehicle speed is 

decreasing to the set speed after 

the vehicle accelerates by 

depressing the accelerator pedal

*

: If equipped

RSA (Road Sign 

Assist)

*

The RSA system recognizes 
specific road signs using 
the front camera to provide 
information to the driver via 
the display.

If the system judges that the 
vehicle is being driven over 
the speed limit, performing 
prohibited actions, etc. in 
relation to the recognized 
road signs, it alerts the 
driver using a warning dis-
play and warning buzzer.

WARNING

■

Before using the RSA

Do not rely solely upon the RSA 

system. RSA is a system which 

supports the driver by providing 

information, but it is not a replace-

ment for a driver’s own vision and 

awareness. Drive safely by 

always paying careful attention to 

the traffic rules.

203

4-5. Using the driving support systems

4

Dr

iv

ing

When the front camera recog-
nizes a sign, the sign will be dis-
played on the multi-information 
display.


When the driving support sys-
tem information is selected, a 
maximum of 3 signs can be 
displayed. (P.89)



When a tab other than the 
driving support system infor-
mation is selected, only a rec-
ognized speed limit sign or do 
not enter sign (when notifica-
tion is necessary) will be dis-
played. (P.89)

If signs other than speed limit signs 
are recognized, they will be dis-
played in an overlapping stack 
under the current speed limit sign.

The following types of road 
signs, including electronic signs 
and blinking signs, are recog-
nized.

A non-official or a recently intro-
duced traffic sign may not be recog-
nized.

In the following situations, the 
RSA system will alert the driver.


When the vehicle speed 
exceeds the speed warning 
threshold of the speed limit 
sign displayed, the sign dis-
play will be emphasized and a 
buzzer will sound.



When the RSA system recog-
nizes a do not enter sign and 
determines that your vehicle 
has entered a no-entry area, 

Indication on the 
multi-information display

Supported types of road 
signs

Speed limit

Do Not Enter

Stop

Yield

Warning display

204

4-5. Using the driving support systems

the displayed sign will flash 
and a buzzer will sound.

Depending on the situation, traf-
fic environment (traffic direction, 
speed unit) may be detected 
incorrectly and a warning dis-
play may not operate properly.

■

Setting procedure

1

Press 

 or 

 of the meter 

control switches and select 

2

Press 

 or 

 of the meter 

control switches and select 

, then press 

■

Automatic turn-off of RSA sign 

display

In the following situations, a dis-

played speed limit sign will stop 

being displayed automatically:

●

A new sign is not recognized for a 

certain distance.

●

The road changes due to a left or 

right turn, etc.

In the following situations, do not 

enter, stop and yield signs will stop 

being displayed automatically:

●

The system determines that your 

vehicle has passed the sign.

●

The road changes due to a left or 

right turn, etc.

■

Conditions in which the func-

tion may not operate or detect 

correctly

In the following situations, RSA 

does not operate normally and may 

not recognize signs, display the 

incorrect sign, etc. However, this 

does not indicate a malfunction.

●

The front camera is misaligned 

due to a strong impact being 

applied to the sensor, etc.

●

Dirt, snow, stickers, etc. are on the 

windshield near the front camera.

●

In inclement weather such as 

heavy rain, fog, snow or sand 

storms.

●

Light from an oncoming vehicle, 

the sun, etc. enters the front cam-

era.

●

The sign is dirty, faded, tilted or 

bent, and if an electronic sign, the 

contrast is poor.

●

All or part of the sign is hidden by 

the leaves of a tree, a pole, etc.

●

The sign is only visible to the front 

camera for a short amount of time.

●

The driving scene (turning, lane 

change, etc.) is judged incorrectly.

●

Even if it is a sign not appropriate 

for the currently traveled lane, 

such a sign exists directly after a 

freeway branches, or in an adja-

cent lane just before merging.

●

Stickers are attached to the rear of 

the preceding vehicle.

●

A sign resembling a system com-

patible sign is recognized.

●

Side road speed signs may be 

detected and displayed (if posi-

tioned in sight of the front camera) 

while the vehicle is traveling on 

the main road.

●

Roundabout exit road speed signs 

may be detected and displayed (if 

positioned in sight of the front 

camera) while traveling on a 

roundabout.

●

The front of the vehicle is raised or 

lowered due to the carried load.

●

The surrounding brightness is not 

sufficient or changes suddenly.

●

When a sign intended for trucks, 

etc. is recognized.

●

The speed information displayed 

on the meter and that displayed 

on the navigation system may be 

different due to the navigation sys-

tem using map data.

■

Speed limit sign display

If the power switch was last turned 

205

4-5. Using the driving support systems

4

Dr

iv

ing

off while a speed limit sign was dis-

played on the multi-information dis-

play, the same sign displays again 

when the power switch is turned to 

ON.

■

If “RSA Malfunction Visit Your 

Dealer” is shown

The system may be malfunctioning. 

Have the vehicle inspected by your 

Toyota dealer.

■

Customization

Some functions can be customized. 

(P.516)

*

: If equipped

BSM (Blind Spot Moni-

tor)

*

The Blind Spot Monitor is a 
system that uses rear side 
radar sensors installed on 
the inner side of the rear 
bumper on the left and right 
side to assist the driver in 
confirming safety when 
changing lanes.

WARNING

■

Cautions regarding the use of 

the system

The driver is solely responsible for 

safe driving. Always drive safely, 

taking care to observe your sur-

roundings.
The Blind Spot Monitor is a sup-

plementary function which alerts 

the driver that a vehicle is in a 

blind spot of the outside rear view 

mirrors or is approaching rapidly 

from behind into a blind spot. Do 

not overly rely on the Blind Spot 

Monitor. As the function cannot 

judge if it is safe to change lanes, 

over reliance could lead to an 

accident resulting in death or seri-

ous injury.
As the system may not function 

correctly under certain condi-

tions, the driver’s own visual con-

firmation of safety is necessary.

206

4-5. Using the driving support systems

Meter control switches

Turning the Blind Spot Monitor 
on/off.

Outside rear view mirror indi-
cators

When a vehicle is detected in a 
blind spot of the outside rear view 
mirrors or approaching rapidly from 
behind into a blind spot, the outside 
rear view mirror indicator on the 
detected side will illuminate. If the 
turn signal lever is operated toward 
the detected side, the outside rear 
view mirror indicator flashes.

BSM indicator

Illuminates when the Blind Spot 
Monitor is enabled

■

Outside rear view mirror indica-

tor visibility

In strong sunlight, the outside rear 

view mirror indicator may be difficult 

to see.

■

When “Blind Spot Monitor 

Unavailable” is shown on the 

multi-information display

Ice, snow, mud, etc., may be 

attached to the rear bumper around 

the sensors. (P.207) The system 

should return to normal operation 

after removing the ice, snow, mud, 

etc. from the rear bumper. Addition-

ally, the sensors may not operate 

normally when driving in extremely 

hot or cold environments.

■

When “Blind Spot Monitor Mal-

function Visit Your Dealer” is 

shown on the multi-information 

display

There may be a sensor malfunction 

of misaligned. Have the vehicle 

inspected by your Toyota dealer.

■

Customization

Some functions can be customized. 

(P.516)

■

Certification



Except for vehicles sold in Canada

System components

207

4-5. Using the driving support systems

4

Dr

iv

ing



For vehicles sold in Canada

WARNING

■

Handling the rear side radar 

sensor

Blind Spot Monitor sensors are 

installed behind the left and right 

sides of the rear bumper respec-

tively. Observe the following to 

ensure the Blind Spot Monitor can 

operate correctly.

●

Keep the sensors and the sur-

rounding areas on the rear 

bumper clean at all times.

If a sensor or its surrounding area 
on the rear bumper is dirty or cov-
ered with snow, the Blind Spot 
Monitor may not operate and a 
warning message (P.206) will 
be displayed. In this situation, 
clear off the dirt or snow and drive 
the vehicle with the operation con-
ditions of the BSM function 
(P.210) satisfied for approxi-
mately 10 minutes. If the warning 
message does not disappear, 
have the vehicle inspected by 
your Toyota dealer.

208

4-5. Using the driving support systems

Use the meter control switches 
to turn on/off the function.

1

Press 

 or 

 to select 

.

2

Press 

 or 

 to select 

 

and then press 

.

■

Vehicles that can be detected by the Blind Spot Monitor

The Blind Spot Monitor uses rear side radar sensors to detect the fol-
lowing vehicles traveling in adjacent lanes and advises the driver of 
the presence of such vehicles via the indicators on the outside rear 
view mirrors.

WARNING

●

Do not attach accessories, 

stickers (including transparent 

stickers), aluminum tape, etc. to 

a sensor or its surrounding area 

on the rear bumper.

●

Do not subject a sensor or its 

surrounding area on the rear 

bumper to a strong impact.

If a sensor is moved even 

slightly off position, the system 

may malfunction and vehicles 

may not be detected correctly.

In the following situations, have 

your vehicle inspected by your 

Toyota dealer.

• A sensor or its surrounding area 

is subject to a strong impact.

• If the surrounding area of a sen-

sor is scratched or dented, or 

part of them has become dis-

connected.

●

Do not disassemble the sensor.

●

Do not modify the sensor or sur-

rounding area on the rear 

bumper.

●

If a sensor or the rear bumper 

needs to be removed/installed 

or replaced, contact your Toyota 

dealer.

●

Do not paint the rear bumper 

any color other than an official 

Toyota color.

Turning the Blind Spot 
Monitor on/off

Blind Spot Monitor operation

209

4-5. Using the driving support systems

4

Dr

iv

ing

Vehicles that are traveling in areas that are not visible using the 
outside rear view mirrors (the blind spots)
Vehicles that are approaching rapidly from behind in areas that 
are not visible using the outside rear view mirrors (the blind spots)

■

The Blind Spot Monitor detection areas

The areas that vehicles can be detected in are outlined below.

The range of each detection area is:

Approximately 1.6 ft. (0.5 m) to 11.5 ft. (3.5 m) from either side of 
the vehicle

*1

Approximately 3.3 ft. (1 m) forward of the rear bumper
Approximately 9.8 ft. (3 m) from the rear bumper
Approximately 9.8 ft. (3 m) to 197 ft. (60 m) from the rear 
bumper

*2

*1

:The area between the side of the vehicle and 1.6 ft. (0.5 m) from the side 

of the vehicle cannot be detected.

*2

:The greater the difference in speed between your vehicle and the 

detected vehicle is, the farther away the vehicle will be detected, causing 
the outside rear view mirror indicator to illuminate or flash.

■

The Blind Spot Monitor is oper-

ational when

The Blind Spot Monitor is opera-

tional when all of the following con-

ditions are met:

●

The Blind Spot Monitor is on.

●

The shift lever is in a position 

other than R.

●

The vehicle speed is greater than 

approximately 10 mph (16 km/h).

■

The Blind Spot Monitor will 

detect a vehicle when

The Blind Spot Monitor will detect a 

vehicle present in the detection area 

in the following situations:

●

A vehicle in an adjacent lane over-

takes your vehicle.

●

You overtake a vehicle in adjacent 

lane slowly.

●

Another vehicle enters the detec-

tion area when it changes lanes.

210

4-5. Using the driving support systems

■

Conditions under which the 

Blind Spot Monitor will not 

detect a vehicle

The Blind Spot Monitor is not 

designed to detect the following 

types of vehicles and/or objects:

●

Small motorcycles, bicycles, 
pedestrians, etc.

*

●

Vehicles traveling in the opposite 

direction

●

Guardrails, walls, signs, parked 

vehicles and similar stationary 
objects

*

●

Following vehicles that are in the 
same lane

*

●

Vehicles traveling 2 lanes away 
from your vehicle

*

●

Vehicles which are being over-
taken rapidly by your vehicle

*

*

: Depending on the conditions, 

detection of a vehicle and/or 
object may occur.

■

Conditions under which the 

Blind Spot Monitor may not 

function correctly

●

The Blind Spot Monitor may not 

detect vehicles correctly in the fol-

lowing situations:

• When the sensor is misaligned 

due to a strong impact to the sen-

sor or its surrounding area

• When mud, snow, ice, a sticker, 

etc. is covering the sensor or sur-

rounding area on the rear bumper

• When driving on a road surface 

that is wet with standing water 

during bad weather, such as 

heavy rain, snow, or fog

• When multiple vehicles are 

approaching with only a small gap 

between each vehicle

• When the distance between your 

vehicle and a following vehicle is 

short

• When there is a significant differ-

ence in speed between your vehi-

cle and the vehicle that enters the 

detection area

• When the difference in speed 

between your vehicle and another 

vehicle is changing

• When a vehicle enters a detection 

area traveling at about the same 

speed as your vehicle

• As your vehicle starts from a stop, 

a vehicle remains in the detection 

area

• When driving up and down con-

secutive steep inclines, such as 

hills, dips in the road, etc.

• When driving on roads with sharp 

bends, consecutive curves, or 

uneven surfaces

• When vehicle lanes are wide, or 

when driving on the edge of a 

lane, and the vehicle in an adja-

cent lane is far away from your 

vehicle

• When an accessory (such as a 

bicycle carrier) is installed to the 

rear of the vehicle

• When there is a significant differ-

ence in height between your vehi-

cle and the vehicle that enters the 

detection area

• Immediately after the Blind Spot 

Monitor is turned on

●

Instances of the Blind Spot Moni-

tor unnecessarily detecting a vehi-

cle and/or object may increase in 

the following situations:

• When the sensor is misaligned 

due to a strong impact to the sen-

sor or its surrounding area

• When the distance between your 

vehicle and a guardrail, wall, etc. 

that enters the detection area is 

short

• When driving up and down con-

secutive steep inclines, such as 

hills, dips in the road, etc.

• When vehicle lanes are narrow, or 

when driving on the edge of a 

lane, and a vehicle traveling in a 

lane other than the adjacent lanes 

enters the detection area

• When driving on roads with sharp 

bends, consecutive curves, or 

uneven surfaces

• When the tires are slipping or 

spinning

• When the distance between your 

211

4-5. Using the driving support systems

4

Dr

iv

ing

vehicle and a following vehicle is 

short

• When an accessory (such as a 

bicycle carrier) is installed to the 

rear of the vehicle

The rear view image is dis-
played when the shift lever is in 
R and the power switch is in ON.

Rear view monitor sys-

tem



Entune Audio

The rear view monitor sys-
tem assists the driver by 
displaying an image of the 
view behind the vehicle with 
fixed guide lines on the 
screen while backing up, for 
example while parking.

The screen illustrations 
used in this text are 
intended as examples, and 
may differ from the image 
that is actually displayed on 
the screen.



Entune Audio Plus

Owners of models equipped 
with a navigation/multime-
dia system should refer to 
the “NAVIGATION AND 
MULTIMEDIA SYSTEM 
OWNER’S MANUAL”.

System overview

212

4-5. Using the driving support systems

The rear view monitor system 

will be deactivated when the 
shift lever is shifted to any posi-
tion other than R.

■

Screen description

The rear view monitor system screen will be displayed if the shift 
lever is shifted to R while the power switch is in ON.

Vehicle width extension guide line

Displays a guide path when the vehicle is being backed straight up. The 
displayed width is wider than the actual vehicle width.

Vehicle center guide line

This line indicates the estimated vehicle center on the ground.

Distance guide line

Displays a point approximately 1.5 ft. (0.5 m) (red) from the edge of the 
bumper.

Distance guide line

Displays a point approximately 3 ft. (1 m) (blue) from the edge of the 
bumper.

Using the rear view monitor system

213

4-5. Using the driving support systems

4

Dr

iv

ing

■

Area displayed on screen

Corners of bumper

The rear view monitor system 
displays an image of the view 
from the bumper of the rear area 
of the vehicle.
The image adjustment proce-
dure for the rear view monitor 
system screen is the same as 
the procedure for adjusting the 
screen. (P.246)


The area displayed on the 
screen may vary according to 
vehicle orientation conditions.



Objects which are close to 
either corner of the bumper or 
under the bumper cannot be 
displayed.



The camera uses a special 
lens. The distance of the 
image that appears on the 
screen differs from the actual 
distance.



Items which are located 
higher than the camera may 
not be displayed on the moni-
tor.

■

Rear view monitor system 
camera

The camera for the rear view 
monitor system is located as 
shown in the illustration.


Using the camera

If dirt or foreign matter (such as 
water droplets, snow, mud etc.) is 
adhering to the camera, it cannot 
transmit a clear image. In this case, 
flush it with a large quantity of water 
and wipe the camera lens clean 
with a soft and wet cloth.

■

Differences between the 
screen and the actual road

The distance guide lines and the 
vehicle width guide lines may 
not actually be parallel with the 
dividing lines of the parking 
space, even when they appear 

Rear view monitor system 
precautions