Subaru XV Crosstrek (2016 year). Instruction - part 9

the power door locking switch to set the
door locks.
7. Close the door. An electronic chirp will
sound once, the hazard warning flashers
will flash once and the security indicator
light will start flashing rapidly. After rapid
flashing for 30 seconds (standby time), the
indicator lights will then flash slowly (twice
approximately every 2 seconds), indicat-
ing that the system has been armed for
surveillance.

! To arm the system using the key-

less access function (if equipped)

1. Close all windows and the moonroof (if
equipped)
2. Turn the push-button ignition switch to
the

“OFF” position.

3. Open the doors and get out of the
vehicle.
4. Make sure that the engine hood is
locked.
5. Close all doors and the rear gate/trunk
lid.

Door lock sensor

Security indicator light (type A)

Security indicator light (type B)

6. Carry the access key and touch the
door lock sensor. All doors (for 5-door,
including the rear gate) will lock, an
electronic chirp will sound once, the
hazard warning flashers will flash once,
and the security indicator light will start
flashing rapidly. After rapid flashing for 30
seconds (standby time), the security in-
dicator light will then flash slowly (twice
approximately every 2 seconds), indicat-
ing that the system has been armed for
surveillance.

If any of the doors or the rear gate is not
fully closed, an electronic chirp sounds
five times, the hazard warning flashers
flash five times to alert you that the doors
(or the rear gate/trunk lid) are not properly
closed. When you close the door, the

Keys and doors/Alarm system

– CONTINUED –

2-31

Keys and doors/Alarm system

system will automatically arm and doors
will automatically lock.

& Disarming the system

Perform either of the following procedures.
. Briefly press the disarm button (for less
than 2 seconds) on the access key/remote
transmitter.
. Carry the access key and perform
either of the following procedures (models
with

“keyless access with push-button

start system

”).

– Grip the front door handle.

– Press the rear gate opener button
(5-door).

The following door(s) will unlock, an
electronic chirp will sound twice and the
hazard warning flashers will flash twice.
. Driver’s door: when either of the
following procedures is performed

– Press the disarm button on the
access key/remote transmitter briefly
(for less than 2 seconds).
– Grip the driver’s door handle (mod-
els with

“keyless access with push-

button start system

”).

. Rear gate (5-door): when pressing the
rear gate opener button (models with

“keyless access with push-button start
system

”)

. All doors: when gripping the front

passenger

’s door handle (models with

“keyless access with push-button start
system

”)

The flashing of the security indicator light
will then change slowly (once approxi-
mately every 3 seconds from twice ap-
proximately every 2 seconds), indicating
that the alarm system has been disarmed.

To unlock all other doors and the rear gate
(5-door), briefly press the disarm button a
second time within 5 seconds.

! Emergency disarming
If you cannot disarm the system using the
access key/transmitter (i.e. the transmitter
is lost, broken or the transmitter battery is
too weak), you can disarm the system
without using the access key/remote
transmitter.
The system can be disarmed if you turn
the ignition switch from the

“LOCK”/“OFF”

to the

“ON” position with a registered key/

access key.

NOTE

For models with

“keyless access with

push-button start system

”, if the ac-

cess key battery is discharged, perform
the procedure described in

“Switching

power

” F9-18. In such a case, replace

the battery immediately. Refer to

“Re-

placing battery of access key

” F11-44.

& Valet mode

When you choose the valet mode, the
alarm system does not operate. In valet
mode, the remote transmitter is used only
for locking and unlocking the doors and
rear gate (5-door) and panic activation.

To enter the valet mode, change the
setting of your vehicle

’s alarm system for

deactivation mode. Refer to

“Activating

and deactivating the alarm system

” F2-

28. The security indicator light will con-
tinue to flash once every 3 seconds
indicating that the system is in the valet
mode.

To exit valet mode, change the setting of
your vehicle

’s alarm system for activation

mode. Refer to

“Activating and deactivat-

ing the alarm system

” F2-28.

& Passive arming (models

without

“keyless access with

push-button start system

”)

! Passive arming mode
When passive arming mode has been
programmed by the dealer, arming of the
system is automatically accomplished
without using the remote transmitter. Note

2-32

that in this mode, DOORS MUST BE
MANUALLY LOCKED.
! To enter the passive mode
If you wish to program the passive arming
mode, have it done by your SUBARU
dealer.
! Arming the system

CAUTION

In passive mode, the system will
automatically activate the alarm but
WILL NOT automatically lock the
doors. In order to lock the doors
you must either lock them as in-
dicated in step 4 below or with the
key once they have been closed.
Failure to lock the doors manually
will result in a higher security risk.

1. Turn the ignition switch to the

“ON”

position.

LOCK

2. Turn the ignition switch from

“ON” to

“LOCK” position and remove the key from
the ignition switch.
3. Open the doors and get out of the
vehicle.

4. Before closing the doors, lock all doors
with the inside door lock levers.
5. Close the doors. The system will
automatically arm after 1 minute.

In the passive mode, the system can also
be armed with the remote transmitter or
with the power door locking switches. If
the remote transmitter or power door
locking switch is used to lock the vehicle,
arming will take place immediately regard-
less of whether or not the passive mode
has been selected.
! Disarming the system
To disarm the system, briefly press the

“ ” button on the transmitter.

Keys and doors/Alarm system

– CONTINUED –

2-33

Keys and doors/Alarm system

& Tripped sensor identification

The security indicator light flashes when
the alarm system has been triggered.
Also, the number of flashes indicates the
location of unauthorized intrusion or the
severity of impact on the vehicle.

When the ignition switch is turned to the

“ON” position, the indicator light will light
for 1 second and then flash as follows.
. When a door or the rear gate (5-door)
was opened: 5 times
. When a door or the trunk (4-door) was
opened: 4 times
. When the ignition switch was turned to
the

“ON” position: 3 times

. When a strong impact or multiple
impacts were sensed: twice (only models
with shock sensors (dealer option))
. When a light impact was sensed: once
(only models with shock sensors (dealer
option))

NOTE

Any of the above indicator light flash-
ings will recur each time the ignition
switch is turned to the

“ON” position.

Rearming the alarm system cancels the
flashing.

& Shock sensors (dealer op-

tion)

The shock sensors trigger the alarm
system when they sense impacts applied
to the vehicle and when any of their
electric wires are cut. The alarm system
causes the horn to sound and the hazard
warning flashers to flash for a short time
when the sensed impact is weak, but it
warns of a strong impact or multiple
impacts by sounding the horn and flashing
the hazard warning flashers, both lasting
approximately 30 seconds.
If you desire, your SUBARU dealer can
connect them and set them for activation
or deactivation.

NOTE

. The shock sensors are not always
able to sense impacts caused by break-
ing in, and cannot sense an impact that
does not cause vibration (such as
breaking the glass using a rescue
hammer).

. The shock sensors may sense vi-
bration as indicated in the following
examples and trigger the alarm system.
Select the settings of the alarm system
and shock sensors appropriately de-
pending on where you usually park
your vehicle.

Examples:

– Vibration from a construction site

– Vibration in a multistory car park

– Vibration from trains

. You can have the sensitivity of the
shock sensors adjusted to your pre-
ference by your SUBARU dealer.

2-34

Child safety locks

Each rear door has a child safety lock.
When the child safety lock lever is in the
lock position, the door cannot be opened
from inside. The door can only be opened
from the outside.

WARNING

Always turn the child safety locks to
the

“LOCK” position when children

sit in the rear seat. Serious injury
could result if a child accidentally
opens the door and falls out.

Windows

WARNING

To avoid serious personal injury
caused by entrapment, always con-
form to the following instructions
without exception.
. When operating the power win-

dows, be extremely careful to
prevent anyone

’s fingers, arms,

neck, head or other objects from
being caught in the window.

. Always lock the passengers’ win-

dows using the lock switch when
children are riding in the vehicle.

. Always carry the key when you

leave the vehicle for safety rea-
sons and never allow an unat-
tended child to remain in the
vehicle. Failure to follow this
procedure could result in injury
to a child operating the power
window.

The power windows operate only when
the ignition switch is in the

“ON” position.

& Power window operation by

driver

! Driver’s side power window

switches

Lock switch

For driver

’s window (with one-touch auto

up and down feature)

For front passenger

’s window

For rear left window

For rear right window

All door windows can be controlled by the
power window switch cluster at the driver
side door.

Keys and doors/Child safety locks

– CONTINUED –

2-35

Keys and doors/Windows

! Operating the driver’s window

Automatically open/close

Open/close

To open:
Push the switch down lightly and hold it.
The window will open as long as the
switch is held.
This switch also has a one-touch auto
down feature that allows the window to be
opened fully without holding the switch.
Push the switch down until it clicks and
release it, and the window will fully open.
To stop the window halfway, pull the
switch up lightly.

To close:
Pull the switch up lightly and hold it. The
window will close as long as the switch is
held.

This switch also has a one-touch auto up
feature that allows the window to be
closed fully without holding the switch.
Pull the switch up until it clicks and release
it, and the window will fully close. To stop
the window halfway, push the switch down
lightly.

NOTE

If the vehicle

’s battery is disconnected

due to situations such as battery or
fuse replacement, the one-touch auto
up/down function will be deactivated.
Initialize the power window to reacti-
vate the one-touch auto up/down func-
tion. Refer to

“Initialization of power

window

” F2-38.

! Anti-entrapment function

CAUTION

. Never attempt to test this func-

tion using fingers, hands or other
parts of your body.

. The anti-entrapment function

may not operate properly if some
object gets trapped just before
the window fully closes.

NOTE

. If a window detects an impact simi-
lar to that caused by trapping an object
(for example, when the vehicle encoun-
ters a deep pothole), the anti-entrap-
ment function may operate.

. The window cannot be operated for
a few seconds after the anti-entrap-
ment function operates.

. If the vehicle’s battery is discon-
nected due to situations such as
battery or fuse replacement, the anti-
entrapment function is deactivated.
Initialize the power window to reacti-
vate the anti-entrapment function. Re-
fer to

“Initialization of power window”

F2-38.
While closing the driver

’s window auto-

matically, if the window senses a sub-
stantial enough object trapped between
the window and the window frame, it
automatically moves down slightly and
stops.

2-36

! Operating the passengers’ win-

dows

To open:
Push the appropriate switch down and
hold it until the window reaches the
desired position.
To close:
Pull the switch up and hold it until the
window reaches the desired position.

! Locking the passengers’ windows

Lock

Unlock

To lock:
Press the lock switch. When the lock
switch is in the lock position, the passen-
gers

’ windows cannot be opened or

closed.
To unlock:
Press the lock switch again.

& Power window operation by

passengers

! Passenger’s side power window

switches

Each passenger window can be controlled
by the power window switch located on
the door.

Keys and doors/Windows

– CONTINUED –

2-37

Keys and doors/Trunk lid (4

–door)

! Operating the windows

To open:
Press the switch down and hold it until the
window reaches the desired position.
To close:
Pull the switch up and hold it until the
window reaches the desired position.

When the lock switch on the power
window switch cluster, located on the
driver

’s side door, is in the lock position,

the passengers

’ windows cannot be oper-

ated with the passengers

’ switches.

& Initialization of power win-

dow

If the vehicle

’s battery is disconnected due

to situations such as battery or fuse
replacement, the following functions are
deactivated.
. One-touch auto up/down function

. Anti-entrapment function

Initialize the power window using the
following procedure to reactivate these
functions.
1. Close the driver

’s door.

2. Turn the ignition switch to the

“ON”

position.
3. Open the driver

’s side window halfway

by pushing down the power window
switch.
4. Pull up the power window switch and
close the window completely. Continue
pulling up the switch for approximately 1
second after the window is closed com-
pletely.
5. Open the driver

’s side window com-

pletely by fully pushing down the power
windows switch.

Trunk lid (4-door)

WARNING

. To prevent dangerous exhaust

gas from entering the vehicle,
always keep the trunk lid closed
while driving.

. Help prevent children, adults or

animals from locking themselves
in the trunk. On hot or sunny
days, the temperature in the
trunk could quickly become high
enough to cause death or serious
heat-related injuries including
brain damage to anyone locked
inside, particularly for small chil-
dren.

. When leaving the vehicle, either

close all windows and lock all
doors. Also make certain that the
trunk is closed.

2-38

& To open and close the trunk

lid from outside

The trunk lid can be opened using the
keyless access function or remote keyless
entry system. For details, refer to the
following section.
. For models with “keyless access with
push-button start system

”, refer to “Open-

ing trunk (4-door)

” F2-16 or “Opening the

trunk lid (4-door)

” F2-25.

. For models without “keyless access
with push-button start system

”, refer to

“Opening the trunk lid (4-door)” F2-25.

To close the trunk lid, lightly press the
trunk lid down until the latch engages.

NOTE

Do not leave your valuables in the
trunk when you leave your vehicle.

& To open the trunk lid from

inside

Pull the trunk lid release lever upward.
The lever is on the floor at the left of the
driver

’s seat.

& Internal trunk lid release

handle

The internal trunk lid release handle is a
device designed to open the trunk lid from
inside the trunk. In the event children or
adults become locked inside the trunk, the
handle allows them to open the lid. The
handle is located on the inside of the trunk
lid.

To open the trunk lid from inside the trunk,
pull the yellow handle upward as indicated
by the arrow on the handle.
This operation unlocks the trunk lid. Then,
push up the lid.

The handle is made of material that
remains luminescent for approximately
an hour in the dark trunk space after it is
exposed to ambient light even for a short

Keys and doors/Trunk lid (4

–door)

– CONTINUED –

2-39

Keys and doors/Trunk lid (4

–door)

time.

WARNING

Never allow any child to get in the
trunk and play with the release
handle. If the driver starts the vehi-
cle without knowing that a child is
inside the trunk and the child opens
the lid using the release handle, the
child could fall out and be killed or
seriously injured.

CAUTION

. Do not close the lid while grip-

ping the release handle. The
handle may be damaged.

. Do not use the handle as a hook

to fasten straps or ropes to
secure your cargo in the trunk.
Such use may result in damage
of the handle.

. Load the trunk so that cargo can

not strike the release handle. If
the cargo hits the handle while
the vehicle is being driven, the
handle may be pulled up and the
trunk lid may open. That may
cause cargo to fall out of the
trunk, which could create a traffic
safety hazard.

! Inspection
Perform the following steps at least twice
a year to check the release handle for
correct operation.
1. Open the trunk lid.

2. Use a flat-head screwdriver with a thin
blade. Slide the screwdriver blade from
the slit aperture of the lock assembly to

the end until you hear a click.

This places the latch in the locked posi-
tion.

3. Pull the trunk lid release handle from
outside the vehicle, as indicated by the
arrow on the handle to check if the latch is

2-40

released.

If the latch is not released, contact your
SUBARU dealer.
In this case, press the

“

” button on the

key lug to release the latch, then close the
trunk lid.
Also, if the movement of the trunk lid
release handle feels restricted or not
entirely smooth during operation, or the
handle and/or handle base is cracked,
contact your SUBARU dealer.

Rear gate (5-door)

& Lock/unlock

The rear gate can be locked and unlocked
using any of the following systems.
. Power door locking switch: Refer to

“Power door locking switches” F2-8.

. Keyless access with the push-button
start system (if equipped): Refer to

“Key-

less access with push-button start system

”

F2-9.

. Remote keyless entry system: Refer to

“Remote keyless entry system” F2-23.

NOTE

If the rear gate cannot be unlocked due
to a discharged vehicle battery, a
malfunction in the door locking/unlock-
ing system or other causes, you can
unlock it by manually operating the
rear gate lock release lever.
For the procedure, refer to

“Rear gate –

if the rear gate cannot be opened

” F9-

19.

& Open/close

To open:
First unlock the rear gate lock then push
the rear gate opener button.

To close:
Lower the rear gate slowly and push down

Keys and doors/Rear gate (5

–door)

– CONTINUED –

2-41

Keys and doors/Moonroof

firmly until the latch engages.
The rear gate can be lowered easily if you
pull it down holding the recessed grip.

WARNING

. To prevent dangerous exhaust

gas from entering the vehicle,
always keep the rear gate closed
while driving.

. Do not attempt to shut the rear

gate while holding the recessed
grip. Also avoid closing the rear
gate by pulling on the recessed
grip from inside the cargo space.
There is a danger of your hand
being caught and injured.

CAUTION

. Do not jam a plastic bag in or

place cellophane tape on the rear
gate stays or scratch the stays
while loading or unloading cargo.
That could cause leakage of gas
from the stays, which may result
in their inability to hold the rear
gate open.

. Be careful not to hit your head or

face on the rear gate when open-
ing or closing the rear gate and

when loading or unloading car-
go.

NOTE

“Rear gate – if the

rear gate cannot be opened

” F9-19.

Moonroof (if equipped)

WARNING

Never let anyone

’s hands, arms,

head or any objects protrude from
the moonroof. A person could be
seriously injured if any of the follow-
ing conditions occur.
. The vehicle stops suddenly.
. The vehicle turns sharply.
. The vehicle is involved in an

accident.

. Body parts protruding from the

vehicle are struck by outside
objects.

To avoid serious personal injury
caused by entrapment, always con-
form to the following instructions
without exception.
. Before closing the moonroof,

make sure that no one

’s hands,

arms, head or other objects will
be accidentally caught in the
moonroof.

. Always carry the key when you

leave the vehicle for safety rea-
sons and never allow an unat-
tended child to remain in the

2-42

vehicle. Failure to follow this
procedure could result in injury
to a child operating the moon-
roof.

. Never try to check the anti-en-

trapment function by deliberately
placing part of your body in the
moonroof.

CAUTION

. Do not sit on the edge of the open

moonroof.

. Do not operate the moonroof if

falling snow or extremely cold
conditions have caused it to
freeze shut.

. The anti-entrapment function

does not operate when the moon-
roof is being tilted down. Be sure
to confirm that it is safe to do so
before tilting the moonroof down.

. If the moonroof does not close,

we recommend that you have the
system checked by a SUBARU
dealer.

The moonroof has both tilting and sliding
functions.

The moonroof operates only when the

ignition switch is in the

“ON” position.

& Moonroof switches

! Tilting moonroof

Raise

Lower

The tilting function is activated only when
the moonroof is fully closed.

To raise:
Press the rear side of the

“UP/DOWN”

switch momentarily. The moonroof raises
completely.

To lower:
Press and hold the front side of the

“UP/

DOWN

” switch until the preferred position

has reached.

Release the switch after the moonroof has
been raised or has been lowered com-
pletely. Pressing the switch continuously
may cause damage to the moonroof.
! Sliding moonroof

Open

To open:
Press and hold the rear side of the

“OPEN/CLOSE” switch. The sun shade
will also be opened together with the
moonroof. The moonroof will stop at a
position approximately 1.6 in (4 cm) away
from the fully opened position. Press and
hold the rear side of the switch again to
open the moonroof completely.

To close:
Press and hold the front side of the

Keys and doors/Moonroof

– CONTINUED –

2-43

Keys and doors/Moonroof

“OPEN/CLOSE” switch.
To stop the moonroof at a selected mid-
way position while opening or closing it,
momentarily push the switch to the

“OPEN” side or “CLOSE” side.

After washing the vehicle or after it rains,
wipe away water on the roof prior to
opening the moonroof to prevent drops
of water from falling into the passenger
compartment.

NOTE

Driving with the moonroof fully open
can cause an annoying sound to be
generated at high speeds. If this oc-
curs, use the moonroof at the initial
stop position of 1.6 in (4 cm) away from
the fully opened position.

! Anti-entrapment function
When the moonroof senses a substantial
enough object trapped between its glass
and the vehicle

’s roof during closure, it

automatically moves back to the fully open
position and stops there. The anti-entrap-
ment function may also be activated by a
strong shock on the moonroof even when
there is nothing trapped.

CAUTION

Never attempt to test this function
using fingers, hands or other parts
of your body.

NOTE

For the sake of safety, it is recom-
mended that you avoid driving with the
moonroof fully opened.

& Sun shade

The sun shade can be slid forward or
backward by hand while the moonroof is
closed.
If the moonroof is opened, the sun shade
also moves back.

2-44

Ignition switch (models without

“keyless

access with push-button start system

”)......... 3-4

LOCK..................................................................

3-4

ACC....................................................................

3-5

ON ......................................................................

3-5

START ................................................................

3-5

Key reminder chime ............................................

3-5

Ignition switch light (if equipped) .........................

3-6

Push-button ignition switch (models with

push-button start system) ...............................

3-6

Safety precautions ..............................................

3-6

Operating range for push-button start system ......

3-6

Switching power .................................................

3-7

When access key does not operate properly ........

3-8

Hazard warning flasher.......................................

3-8

Meters and gauges..............................................

3-9

Combination meter illumination ...........................

3-9

Canceling the function for meter/gauge needle

movement upon turning on the ignition
switch...............................................................

3-9

Speedometer......................................................

3-10

Odometer...........................................................

3-10

Double trip meter ...............................................

3-11

Tachometer ........................................................

3-11

Fuel gauge .........................................................

3-12

ECO gauge (if equipped) ....................................

3-12

Warning and indicator lights .............................

3-13

Initial illumination for system check ....................

3-13

Seatbelt warning light and chime ........................

3-14

SRS airbag system warning light ........................

3-15

Front passenger

’s frontal airbag ON and OFF

indicators ........................................................

3-16

CHECK ENGINE warning light/Malfunction

indicator light ..................................................

3-16

Coolant temperature low indicator light/Coolant

temperature high warning light.........................

3-17

Charge warning light..........................................

3-18

Oil pressure warning light ..................................

3-18

Engine low oil level warning light .......................

3-18

Windshield washer fluid warning light ................

3-19

AT OIL TEMP warning light (CVT models) ...........

3-19

Low tire pressure warning light (U.S.-spec.

models) ...........................................................

3-19

ABS warning light..............................................

3-21

Brake system warning light (red)........................

3-21

Low fuel warning light .......................................

3-22

Hill start assist warning light/Hill start assist OFF

indicator light ..................................................

3-22

Door open warning light ....................................

3-23

All-Wheel Drive warning light (CVT models) ........

3-23

Power steering warning light..............................

3-23

Vehicle Dynamics Control warning light/Vehicle

Dynamics Control operation indicator light .......

3-24

Vehicle Dynamics Control OFF indicator light .....

3-25

Warning chimes and warning indicator of the

keyless access with push-button start system (if
equipped) ........................................................

3-25

Security indicator light .......................................

3-30

Select lever/gear position indicator (CVT

models) ...........................................................

3-30

Turn signal indicator lights.................................

3-31

High beam indicator light ...................................

3-31

Instruments and controls

Cruise control indicator light (if equipped) ..........

3-31

Cruise control set indicator light (if

equipped).........................................................

3-31

Automatic headlight beam leveler warning light

(models with HID headlights) ............................

3-31

Front fog light indicator light (if equipped) ..........

3-31

Headlight indicator light (if equipped) .................

3-32

Steering responsive fog lights warning indicator/

Steering responsive fog lights OFF indicator
(models with EyeSight system) .........................

3-32

BSD/RCTA warning indicator (if equipped) ..........

3-32

BSD/RCTA OFF indicator (if equipped) ................

3-32

Information display (if equipped) ......................

3-32

Outside temperature indicator ............................

3-33

Driving information display.................................

3-33

Clock .................................................................

3-37

Multi information display (models with type

B combination meter) .....................................

3-38

Basic operation ..................................................

3-39

Welcome screen and Good-bye screen ...............

3-39

Warning screen ..................................................

3-40

Basic screens ....................................................

3-40

Menu screens ....................................................

3-40

Multi function display ........................................

3-42

Models without multi function display .................

3-42

Safety precautions .............................................

3-43

Features ............................................................

3-43

Locations...........................................................

3-43

Basic operation ..................................................

3-44

Welcome screen.................................................

3-44

Date screen........................................................

3-44

Ending screen ...................................................

3-45

Self-check screen ..............................................

3-45

Interruption screen ............................................

3-46

Basic screens....................................................

3-47

Selection screen ................................................

3-54

Date and time settings .......................................

3-57

Image quality and volume settings .....................

3-64

Screen settings..................................................

3-66

Maintenance settings .........................................

3-74

Driving history registration.................................

3-77

Car settings.......................................................

3-78

Initialize.............................................................

3-86

Light control switch...........................................

3-89

Precautions and tips ..........................................

3-89

Headlights .........................................................

3-89

High/low beam change (dimmer) ........................

3-91

Headlight flasher ...............................................

3-91

Daytime running light system.............................

3-92

Turn signal lever ................................................

3-92

One-touch lane changer .....................................

3-93

Illumination brightness control.........................

3-93

Headlight beam leveler (if equipped) ...............

3-94

Automatic headlight beam leveler (models with

HID headlights) ................................................

3-94

Fog light switch (if equipped) ...........................

3-94

Steering responsive fog lights system (models

with EyeSight system) .....................................

3-95

Wiper and washer..............................................

3-96

Windshield wiper and washer switches ..............

3-97

Rear window wiper and washer switch

–

5-door .............................................................

3-99

Content .. 7 8 9 10 ..