Subaru Legacy IV (2008 year). Manual - part 547

 

  Index      Subaru     Subaru Legacy IV - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  545  546  547  548   ..

 

 

Subaru Legacy IV (2008 year). Manual - part 547

 

 

EN(H6DO)(diag)-161

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

AN:DTC P0134 O2 SENSOR CIRCUIT NO ACTIVITY DETECTED 

(BANK 1 SENSOR 1)

DTC DETECTING CONDITION:
• Immediately at fault recognition
• GENERAL DESCRIPTION <Ref. to GD(H6DO)-58, DTC P0134 O2 SENSOR CIRCUIT NO ACTIVITY
DETECTED (BANK 1 SENSOR 1), Diagnostic Trouble Code (DTC) Detecting Criteria.>

CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H6DO)(diag)-52,
OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H6DO)(diag)-44, PROCEDURE,
Inspection Mode.>.
WIRING DIAGRAM:

SBF-5

BATTERY

E

E3

B22

B47

1

2

3

5

4

6

MAIN RELAY

E3

B22

8

 : TERMINAL No. OPTIONAL ARRANGEMENT 
  AMONG 1, 2, 5 AND 6

*

3

4

5

6

1

2

B47

1 2 3 4
5 6 7 8
9 10 11 12

13 14 15 16

B22

3 4

1 2

E47

E24

16

10 11 12 13 14 15

25

24

30

9

8

7

17 18 19 20
28

21 22 23

29

32

31

1

2

3

4

5

6

27

26

33 34 35

B136

C:

5

6

7

8

2

1

9

4

3

10

22 23

11 12 13 14 15

24 25

26

16 17

18 19 20 21

27

28 29

30 31

B137

D:

1 2 3 4
5 6 7 8

B138

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17 18 19

20 21

29 30 31

32 33

34 35

B135

B:

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17

18 19 20 21

33 34

29

32

30 31

B134

A:

B11

2

E24

FRONT 

OXYGEN (A/F) 

SENSOR LH

3

4

B10

1

B7

B6

C2

C3

B8

4

1

3

B9

ECM

B135

B:

B134

A:

B137

D:

B136

C:

D3

A3

D2

D1

D7

A5

35

34

52

36

37

B21

E2

E

E

EN-06867

B21

1 2 3 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33

34

35

42

43

36

37

38

39

48

49

50

51

52

53

54

40

41

44

45

46

47

2

E47

FRONT 

OXYGEN (A/F) 

SENSOR RH

5

6

7

4

2

1

3

B138

*

*

B1

EN(H6DO)(diag)-162

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK HARNESS BETWEEN ECM AND 
FRONT OXYGEN (A/F) SENSOR CONNEC-
TOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and 
front oxygen (A/F) sensor connector.
3) Measure the resistance of harness between 
ECM and front oxygen (A/F) sensor connector.

Connector & terminal

(B135) No. 9 — (E47) No. 3:
(B135) No. 8 — (E47) No. 4:

Is the resistance less than 1 

:? Go to step 2.

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and front oxy-
gen (A/F) sensor
connector
• Poor contact of
coupling connector

2

CHECK POOR CONTACT.
Check for poor contact of ECM and front oxygen 
(A/F) sensor connector.

Is there poor contact in ECM or 
front oxygen (A/F) sensor con-
nector?

Repair the poor 
contact in ECM or 
front oxygen (A/F) 
sensor connector.

Replace the front 
oxygen (A/F) sen-
sor. <Ref. to 
FU(H6DO)-32, 
Front Oxygen (A/F) 
Sensor.>

EN(H6DO)(diag)-163

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

AO:DTC P0137 O2 SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2)

DTC DETECTING CONDITION:
• Two consecutive driving cycles with fault
• GENERAL DESCRIPTION <Ref. to GD(H6DO)-60, DTC P0137 O2 SENSOR CIRCUIT LOW VOLTAGE
(BANK 1 SENSOR 2), Diagnostic Trouble Code (DTC) Detecting Criteria.>

CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H6DO)(diag)-52,
OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H6DO)(diag)-44, PROCEDURE,
Inspection Mode.>.
WIRING DIAGRAM:

B47

3

4

5

6

1

2

B22

1 2 3 4
5 6 7 8
9 10 11 12

13 14 15 16

1 2 3 4
5 6 7 8

B83

B138

3 4

1 2

E25

E61

B47

1

2

3

5

4

6

E3

B22

14

MAIN RELAY

2

4

3

1

E25

13

15

16

E3

B22

10

11

12

9

SBF-5

BATTERY

2

E61

4

3

1

*

1

*

1

*

1

B83

B138

ECM

B134

A:

B135

B:

B136

C:

B137

D3

A3

D2

D1

D7

A5

D:

C5

*

*

2

2

C4

E

B1

B15

B4

B30

35

34

52

36

37

B21

E2

E

E

 : TERMINAL No. OPTIONAL ARRANGEMENT

*

1

 : TERMINAL No. OPTIONAL ARRANGEMENT 
  AMONG 1, 2, 5 AND 6

*

2

EN-06868

16

10 11 12 13 14 15

25

24

30

9

8

7

17 18 19 20
28

21 22 23

29

32

31

1

2

3

4

5

6

27

26

33 34 35

B136

C:

5

6

7

8

2

1

9

4

3

10

22 23

11 12 13 14 15

24 25

26

16 17

18 19 20 21

27

28 29

30 31

B137

D:

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17 18 19

20 21

29 30 31

32 33

34 35

B135

B:

5

6

7

8

2

1

9

4

3

10

24

22 23

25

11 12 13 14 15

26 27

28

16 17

18 19 20 21

33 34

29

32

30 31

B134

A:

B21

1 2 3 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33

34

35

42

43

36

37

38

39

48

49

50

51

52

53

54

40

41

44

45

46

47

REAR
OXYGEN 
SENSOR LH

REAR
OXYGEN 
SENSOR RH

EN(H6DO)(diag)-164

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK REAR OXYGEN SENSOR DATA.
1) Warm up the engine until engine coolant 
temperature is above 75°C (167°F), and keep 
the engine speed at 3,000 rpm. (for up to 2 min-
utes)
2) Read the data of rear oxygen sensor signal 
using Subaru Select Monitor or general scan 
tool.

NOTE:
• SUBARU SELECT MONITOR
For detailed operation procedure, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H6DO)(diag)-34, Subaru Select Moni-
tor.>
• General Scan Tool
For detailed operation procedures, refer to the
general scan tool operation manual.

Is the voltage 490 mV or more? Go to step 5.

Go to step 2.

2

CHECK REAR OXYGEN SENSOR CONNEC-
TOR AND COUPLING CONNECTOR.

Has water entered the connec-
tor?

Completely 
remove any water 
inside.

Go to step 3.

3

CHECK HARNESS BETWEEN ECM AND 
REAR OXYGEN SENSOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and 
rear oxygen sensor.
3) Measure the resistance of harness between 
ECM and rear oxygen sensor connector.

Connector & terminal

(B135) No. 4 — (E61) No. 3:
(B135) No. 30 — (E61) No. 4:

Is the resistance less than 1 

:? Go to step 4.

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and rear oxy-
gen sensor con-
nector
• Poor contact of
coupling connector

4

CHECK HARNESS BETWEEN ECM AND 
REAR OXYGEN SENSOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from rear oxygen 
sensor.
3) Turn the ignition switch to ON.
4) Measure the voltage between rear oxygen 
sensor connector and chassis ground.

Connector & terminal

(E61) No. 3 (+) — Chassis ground (–):

Is the voltage 0.2 — 0.5 V?

Replace the rear 
oxygen sensor. 
<Ref. to 
FU(H6DO)-34,
Rear Oxygen Sen-
sor.>

Repair the harness 
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
the ECM and rear
oxygen sensor
• Poor contact of
the rear oxygen
sensor connector
• Poor contact in
ECM connector

5

CHECK EXHAUST SYSTEM.
Check exhaust system parts.

NOTE:
Check the following items.
• Looseness and improper attachment of ex-
haust system parts
• Damage (crack, hole etc.) of parts
• Looseness and improper attachment of parts
between front oxygen (A/F) sensor and rear ox-
ygen sensor

Is there any fault in exhaust 
system?

Repair or replace 
faulty parts.

Replace the rear 
oxygen sensor. 
<Ref. to 
FU(H6DO)-34, 
Rear Oxygen Sen-
sor.>

 

 

 

 

 

 

 

Content   ..  545  546  547  548   ..