SsangYong: Engine Euro 4. Manual - part 71

 

  Index      SsangYong     SsangYong: Engine Euro 4 - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  69  70  71  72   ..

 

 

SsangYong: Engine Euro 4. Manual - part 71

 

 

O : Turning on when the condition is occurred twice consecutively

• 

: Turning on when the condition is occurred once

New DTC

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

72

DIAGNOSIS

ECU

DTC

Trouble

Engine CHECK

warning lamp

Help

Related

I t e m

P0117

Coolant Temperature
Sensor Malfunction -
Open circuit

xxxxx

Condition

- The sensor value is less than minimum specified value (0.11 V).

- Related circuit: open circuit

xxxxx

Specification

20°C - 2.50 k

Ω - 3.57 V

80°C - 0.32 k

Ω - 1.22 V

100°C - 0.18 k

Ω - 0.78 V

xxxxx

Actions

1. Measure the actual temperature using SCAN-100.

2. Inspect the circuits of ECU pin No. 78 and 79.

3. Check the coolant temperature sensor.

4. Check the ECU.

P0118

Coolant Temperature
Sensor Malfunction -
Short circuit

xxxxx

Condition

- The sensor value is over the maximum specified value (4.96 V).

- Related circuit: short circuit

xxxxx

Specification

20°C - 2.50 k

Ω - 3.57 V

80°C - 0.32 k

Ω - 1.22 V

100°C - 0.18 k

Ω - 0.78 V

xxxxx

Actions

1. Measure the actual temperature using SCAN-100.

2. Inspect the circuits of ECU pin No. 78 and 79.

3. Check the coolant temperature sensor.

4. Check the ECU.

O

O

Coolant
Temperature
Sensor

Throttle
Body
Control

No.1 Throttle Position
Sensor - Low Voltage

xxxxx

Condition

- No.1 throttle position sensor circuit: short or open circuit to

ground.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor

No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V

- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.

2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.

4. Check the ECU.

P0120

O

O : Turning on when the condition is occurred twice consecutively

• 

: Turning on when the condition is occurred once

New DTC

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

73

DIAGNOSIS

ECU

BRAKE

ECU

TCU

A/BAG

TC

RK-STICS

FFH

R/SENSOR

FA

T

C

TGS-LEVER

P/TRUNK

CCCS

DTC

Trouble

Engine CHECK

warning lamp

Help

Related

I t e m

No.1 Throttle Position
Sensor - High Voltage

xxxxx

Condition

- No.1 throttle position sensor’s main power is grounded.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

No.2 Throttle Position
Sensor - Low Voltage

xxxxx

Condition

- No.2 throttle position sensor circuit: short or open circuit to ground.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

Throttle
Body
Control

P0120

No.2 Throttle Position
Sensor - High Voltage

xxxxx

Condition

- No.2 throttle position sensor’s main power is grounded.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

O : Turning on when the condition is occurred twice consecutively

• 

: Turning on when the condition is occurred once

New DTC

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

74

DIAGNOSIS

ECU

DTC

Trouble

Engine CHECK

warning lamp

Help

Related

I t e m

Throttle Actuator -
Insuffcient Supply
Power

xxxxx

Condition

- Actuator circuit: short circuit

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

TPS Valve Inconsistent
with HFM Sensor Value

xxxxx

Condition

- The potentiometer is defective.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

Both Throttle Position
Sensors Malfunction

xxxxx

Condition

- The potentiometer is defective.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

Throttle
Body
Control

P0120

O : Turning on when the condition is occurred twice consecutively

• 

: Turning on when the condition is occurred once

New DTC

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

75

DIAGNOSIS

ECU

BRAKE

ECU

TCU

A/BAG

TC

RK-STICS

FFH

R/SENSOR

FA

T

C

TGS-LEVER

P/TRUNK

CCCS

DTC

Trouble

Engine CHECK

warning lamp

Help

Related

I t e m

Inconsistent Signals of
No.1 and No.2 Throttle
Position Sensors

xxxxx

Condition

- The difference in amount of 1/2 is occurred in

potentiometer.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

Throttle Actuator
Control Malfunction

xxxxx

Condition

- The wiring or actuator is defective.

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

O

Throttle
Body
Control

P0120

Intake Air Flow Sensor
and Throttle Sensor
Malfunction

xxxxx

Specification

- Connection between No.1 throttle position sensor and No.2

throttle position sensor
No.1 TPS’s pull-down resistance: 464 k

Ω

No.2 TPS’s pull-up resistance: 464 k

Ω

- Potentiometer voltage: 5 V
- Potentiometer resistance: 1 k

Ω ± 20 %

- Permissible current for wiper arms: below 15 

μΑ

- Protective resistance for wiper arms: 320 

Ω ± 20 %

- Motor voltage/max. current

: 12 V / below 1.7 A

xxxxx

Actions

1. Measure the actual output value using SCAN-100.
2. Inspect the circuits and terminals of ECU pin No. 67, 68, 84,

85, 87 and 112.

3. Inspect the electric throttle controller.
4. Check the ECU.

O

 

 

 

 

 

 

 

Content   ..  69  70  71  72   ..