SsangYong Stavic / SsangYong Rodius (2005 year). Manual - part 418

 

  Index      SsangYong     SsangYong Stavic / SsangYong Rodius - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  416  417  418  419   ..

 

 

SsangYong Stavic / SsangYong Rodius (2005 year). Manual - part 418

 

 

ABS/ESP SYSTEM

STAVIC - 2004.09

55

4K

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

Initial start

(for 1.8 sec)

Normal mode

ESP fault

ABS fault

System fault

Low batt. voltage 1

st

Low batt. voltage 2

nd

High battery voltage

High brake pad temp.

ESP-OFF mode

Entering diag. mode

EBD

W/L

ON

OFF

OFF

OFF

ON

OFF

ON

ON

OFF

OFF

ON

ABS

W/L

ON

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

ON

ESP

W/L

ON

BLINKS

WHEN ESP

OPERATION

ON

ON

ON

ON

ON

ON

ON

ON

ON

ESP

BUZZER

OFF

INTERMITTENT BEEP

SOUNDS WHEN ESP

OPERATION

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

EBD

X

O

O

O

X

O

X

X

O

O

X

ABS

X

O

O

X

X

X

X

X

O

O

X

ASR

X

O

X

X

X

X

X

X

* * O

X

X

ABD

X

O

X

X

X

X

X

X

X

X

X

Vehicle

yaw

control

X

O

X

X

X

X

X

X

O

*O

X

ESP Warning Lamp Operation Depending on System Conditions

The table shows ESP warning lamp operations when the ESP system is defective or ESP (including TCS function) is
working.

*) When the driver presses the brake pedal during the ESP OFF mode, the yaw control is performed to compensate

the vehicle stability (posture) during ESP operation.

* *) The ASR controls only engine control

Warning Lamp

Controls

ABS/ESP SYSTEM

STAVIC - 2004.09

56

4K

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

7. REMOVAL AND INSTALLATION

HECU Assembly

Preceding Work: Disassemble the battery negative

cable.

1. Unscrew battery mounting bracket bolts (12M - 2EA)

and remove battery assembly.

2. Unscrew preheating relay mounting bracket bolts (12M -

2EA) and battery tray mounting bolts (12M - 4EA).

3. Disconnect the control unit connector.

ABS/ESP SYSTEM

STAVIC - 2004.09

57

4K

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

4. Disconnect the primary and secondary master cylinder

pipes from HECU.

5. Disconnect the front and rear wheel brake pipes.

7. Install in the reverse order of removal.

8. After reinstallation, add some oil and perform the brake

air bleeding.

6. Unscrew the HECU mounting nuts (2EA), and remove it.

Tightening torque

20 ~ 24 Nm

Tightening torque

15 ~ 19 Nm

RL: Rear left

RR: Rear right

FL: Front left

FR: Front right

 Secondary

Primary

 [Notice]

Be careful not to damage the HECU pipe and nut thread
when reinstall.

[Notice]

Donot attempt to disassemble the HECU assembly.

Wrap the end of pipes and HECU to prevent comtaminating.

[Notice]

When you install a new HECU to the vehicle, Coding is excuted
automatically.

ABS/ESP SYSTEM

STAVIC - 2004.09

58

4K

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

Steering Wheel Sensor

1. Disconnect the battery negative cable and align the tires straight forward.

2. Remove the airbag module.

3. Unscrew the steering wheel mounting nut and remove the wheel.

4. Remove the I/P panel lower cover.

 [Notice]

Leave marks on the column shaft(A) and on the wheel(B).

 

 

 

 

 

 

 

Content   ..  416  417  418  419   ..