Renault Megane Electric (2022 year). Manual in english - page 4

 

  Index      Manuals     Renault Megane Electric (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     2      3      4      5     ..

 

 

 

Renault Megane Electric (2022 year). Manual in english - page 4

 

 

CHILD SAFETY: General information (2/2)
Using a child seat
Before fitting a child seat, read the
manual and respect its instructions. If
The level of protection offered by the
you experience any difficulties during
child seat depends on its ability to re-
installation, contact the manufacturer
strain your child and on its installation.
of the equipment. Keep the instructions
Incorrect installation compromises the
with the seat.
protection it offers the child in the event
of harsh braking or an impact.
Before purchasing a child seat, check
that it complies with the regulations for
the country you are in and that it can
be fitted in your vehicle. Consult an ap-
proved dealer to find out which seats
are recommended for your vehicle.
The regulations on transporting chil-
Never leave a child unat-
dren are specific to each country. The
tended in the vehicle.
use of a child seat during transport de-
pends on the age and/or the size and/
Check that your child is
or weight of the child.
always strapped in and that
the belt or safety harness used is
For children who do not need to be
Set a good example by always fas-
correctly set and adjusted. Avoid
transported in a child seat, make sure
tening your seat belt and teaching
wearing bulky clothing which could
that the seat belt is correctly adjusted
your child:
cause the belts to slacken.
and fastened.
- to strap themselves in correctly;
Never let your child put their head or
In all cases, you must comply with the
- to always get in and out of the car
arms out of the window.
regulations of the particular country you
at the kerb, away from busy traf-
are in.
Check that the child is in the correct
fic.
position for the entire journey, espe-
Do not use a second-hand child
cially if asleep.
seat or one without an instruction
manual.
Check that there are no objects in
the vicinity of the child seat which
could impede its operation.
1.63
CHILD SAFETY: choosing a child seat
Rear-facing child seats
Forward-facing child seats
Booster cushions
A baby’s head is, proportionally, heavier
Up to 18 kg or 4 years, the child may
From 15 kg or 4 years, the child can
than that of an adult and its neck is very
travel on a forward-facing seat.
travel using a booster seat, which will
fragile. Transport the child in this po-
enable the seat belt to be adapted
Choose your seat according the child’s
sition for as long as possible (until the
to suit his/her size and shape. The
size: their head and abdomen are the
age of 2 at the very least). It supports
booster seat cushion must be fitted with
areas which must be most protected. A
both the head and the neck.
guides to position the seat belt on the
forward-facing child seat which is firmly
child’s thighs rather than the stomach.
Choose a bucket type seat for best side
attached to the vehicle will reduce the
It is recommended that you use a seat-
protection and change it as soon as the
risk of impact to the head. Ensure your
back fitted with a belt strap guide which
child’s head is higher than the shell.
child travels in a forward-facing seat
can be adjusted in terms of height to
with a harness for as long as their size
position the seat belt in the centre of the
permits.
shoulder. It must never rest on the neck
Choose a bucket type seat for optimum
or on the arm.
side protection.
Choose a bucket type seat for optimum
side protection.
1.64
CHILD SAFETY: choosing a child seat mounting (1/3)
There are two ways of attaching child
seats: via the seat belt or using the
ISOFIX system.
Attachment via the seat belt
The seat belt must be adjusted to
ensure that it is effective in the event of
harsh braking or an impact.
Ensure that the strap paths indicated
by the child seat manufacturer are re-
spected.
Always check that the seat belt is cor-
rectly fastened by pulling it up, then
pulling it out fully whilst pressing on the
child seat.
The seat belt must never
be twisted or the tension re-
Check that the seat is correctly held by
lieved.
moving it from side to side and back
to front: the seat should remain firmly
Never pass the shoulder
fixed.
strap under the arm or behind the
back.
Check that the child seat has not been
installed at an angle and that it is not
Check that the seat belt has not
resting against a window.
been damaged by sharp edges.
If the seat belt does not operate nor-
mally, it will not protect the child.
Do not use the child seat
Consult an approved dealer.
if it may unfasten the seat
belt restraining it: the base
Do not use this seat until the seat
of the seat must not rest on
belt has been repaired.
the buckle and/or catch of the seat
belt.
1.65
CHILD SAFETY: choosing a child seat mounting (2/3)
Attachment using the ISOFIX
Attach the child seat with the ISOFIX
system
locks, if these are provided. The ISOFIX
system allows quick, easy, safe fitting.
Approved child seats ISOFIX are stand-
ardised in accordance with current reg-
The ISOFIX system consists of two
ulations if any of the four cases below
rings and, in some cases, a third ring.
applies:
- ISOFIXuniversal 3-point forward-fac-
ing seat;
- ISOFIXsemi-universal 2-point seat;
- specific;
1
- i-Size which has either:
The ISOFIX anchorage
- a strap which attaches to the third
points have been exclu-
ring of the seat concerned;
sively designed for child
- or a strut that rests on the vehi-
seats with the ISOFIX
cle floor, compatible with the ap-
system.
proved seat i-Size, the role of
Never fit a different type of child
The two rings 1 are located between the
which is to prevent the child seat
seat, seat belt or other objects to
seatback and the seat base of the seat
from moving in the event of a col-
these fittings.
lision.
and are identified by a
symbol.
Check that nothing is obstructing
In the latter three cases check that your
the anchorage points.
child seat can be installed by consulting
the list of compatible vehicles.
If your vehicle has been involved in
a road accident, have the ISOFIX
anchorage points checked and re-
place your child seat.
No modifications may be
made to the component
Before using an ISOFIX child seat that you purchased for another vehi-
parts of the restraint system
cle, check that its installation is authorised. Consult the list of vehicles
(ISOFIX seat belts, seats
which can be fitted with the seat from the equipment manufacturer.
and their mountings) originally fitted.
1.66
CHILD SAFETY: choosing a child seat mounting (3/3)
2
The ISOFIX anchorage
points have been exclu-
sively designed for child
seats with the ISOFIX
2
system. Never fit a different type of
3
3
child seat, seat belt or other objects
to these anchorage points.
Check that nothing is obstructing
4
the anchorage points.
4
If your vehicle has been involved in
a road accident, have the ISOFIX
anchorage points checked and re-
place your child seat.
Attachment using the ISOFIX
Front passenger seat
system (continued)
Attach the 3 hook of the upper strap 2 to
The third ring 4 is used to attach the
the ring 4 marked with the symbol.
upper strap 2 on some child seats.
All seats
Check that the seatback
Rear seats
of the forward-facing child
Pull the upper strap 2 so that the back
seat is in contact with the
The upper strap 2 should be positioned
of the child seat comes into contact with
seatback of the vehicle
between the seatback and the rear
the back of the vehicle seat.
seat. In this case, the child seat may
parcel shelf. To do so, remove the rear
not always rest on the seat base of
parcel shelf ➥ 3.34.
the vehicle seat.
Attach the 3 hook on one of the 4 rings
marked with the symbol.
The child seat strap must
be attached to the corre-
sponding ring.
1.67
CHILD SAFETY: fitting a child seat: general information (1/2)
Some seats are not suitable for fitting
The types of child seat indicated may
After installing the child seat, when this
child seats.
not be available. Before using a differ-
is possible, you can move the vehi-
ent child seat, check with the manufac-
cle seat forward if necessary (so as to
The diagrams on pages ➥ 1.70 and
turer that it can be fitted.
leave enough space in the rear seats
➥ 1.73 show you where to fit a child
for passengers or other child seats).
seat.
In the front seat
For a rear-facing child seat, do not let
The laws concerning children travel-
it touch the dashboard or move it to the
ling in the front passenger seat differ in
furthest forward position.
every country. Consult the legislation in
Do not change other settings after in-
Fit the child seat in a rear
force and follow the indications on the
stalling the child seat.
seat wherever possible.
diagram on the following page.
Make sure the child seat or
Before fitting a child seat in this seat (if
the child’s feet do not pre-
authorised):
vent the front seat from locking cor-
- lower the seat belt as far as possible;
rectly ➥ 1.38.
- move the seat as far back as possi-
Check that when installing the child
ble;
seat in the vehicle it is not at risk of
- gently tilt the seatback away from
coming loose from its base.
vertical (approximately 25°);
If you have to remove the headrest,
- on equipped vehicles, raise the seat
check that it is correctly stored so
base as far as possible.
that it does not come loose under
harsh braking or impact.
Always fully raise the seat headrest so
that it does not interfere with the child
Always attach the child seat to the
seat ➥ 1.37.
vehicle even if it is not in use so that
it does not come loose under harsh
braking or impact.
RISK
OF
DEATH
OR
SERIOUS INJURY: after fit-
ting a rear-facing child seat
in this seat, make sure that
the
airbag is disabled
➥ 1.58
➥ 1.76.
1.68
CHILD SAFETY: fitting a child seat: general information (2/2)
In the rear side seat
Always remove the headrest from the
Rear centre seat
rear seat on which the child seat is
A carrycot can be installed across the
Check that the belt is suitable for se-
positioned ➥ 3.32. If necessary, posi-
vehicle and will take up at least two
curing your child seat. Consult an ap-
tion the rear seat as far back as pos-
seats. Position the child with his or her
proved dealer.
sible. This must be done before fitting
feet nearest the door.
the child seat. Check that the child seat
Move the front seat as far forward as
is resting against the back of the rear
possible to install a rear-facing child
seat.
seat, then move back the seat in front
as far as it will go, although without al-
lowing it to come into contact with the
child seat.
For the safety of the child in the for-
ward-facing position:
- move the relevant seat backwards
as far as possible;
- move the seat in front of the child
forwards, and set the position of the
A child seat with a floor sup-
seatback to avoid contact between
port must never be installed
the seat and the child’s legs.
on the rear centre seat.
RISK OF DEATH OR
SERIOUS INJURY.
When fitting a child seat
Fit the child seat in a rear
(group 2 or 3 booster seat),
seat wherever possible.
check that the seat belts
To install an ISOFIX seat in
Make sure the child seat or
operate
(wind) correctly
this seat, detach the central
the child’s feet do not pre-
➥ 1.44. If necessary, adjust the posi-
seat belt by hand before engaging
vent the front seat from
tion of the vehicle seat.
the bolts.
locking correctly ➥ 1.38.
1.69
CHILD SEATS: attachment by seat belt (1/3)
The table below summarises the information already shown on the diagram on the next page, to ensure the regulations
in force are respected.
Five-seater version
Front passenger seat
Rear side
Rear centre
Type of child seat
Weight of the child
With airbag
seats
seat
With airbag disabled
activated
Carrycot
fitted
across the vehicle
< 10 kg
X
X
U (2)
U (2)
Group 0
Rear-facing shell
seat
< 10 kg and < 13 kg
U (1) (5)
X
U (3)
U (3) (6)
Groups 0 or 0 +
Shell seat/rear-facing
seat
< 13 kg and 9 to 18 kg
U (1) (5)
X
U (3)
U (3) (6)
Groups 0+ and 1
Forward-facing seat
9 to 18 kg
U (5)
X
U (4)
U (4) (6)
Group 1
Booster seat
15 to 25 kg and 22 to
U (5)
X
U (4)
U (4)
Groups 2 and 3
36 kg
(1) RISK OF DEATH OR SERIOUS INJURY: after fitting a rear-facing child seat in this seat, make sure that the front
passenger airbag is disabled ➥ 1.58 ➥ 1.76.
1.70
CHILD SEATS: attachment by seat belt (2/3)
X = Seat not suitable for fitting child seats of this type.
U = Seat allowing a child seat with “Universal” approval to be attached by the seat belt; check that it can be fitted.
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat
as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the
child seat.
(4) In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the
child seat ➥ 3.32. Move the seat in front of the child forwards, move the seatback forward to avoid contact between the seat
and the child’s legs.
(5) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
(6) RISK OF DEATH OR SERIOUS INJURY: a child seat with a floor support must never be fitted.
1.71
CHILD SEATS: attachment by seat belt (3/3)
³
Check the status of the airbag
before fitting a child seat or allowing a
passenger to use the seat.
Seat not suitable for fitting
²
child seats.
Child seat attached using the belt
¬
Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
RISK OF DEATH OR
Using a child safety system
SERIOUS INJURY: after fit-
which is not approved for
ting a rear-facing child seat
this vehicle will not correctly
in this seat, make sure that
protect the baby or child.
the front passenger airbag is disa-
They risk serious or even fatal injury.
Do not fit a child seat when
bled ➥ 1.58 ➥ 1.76.
the large seat back is in the
folded position.
1.72
CHILD SEATS: attachment using the ISOFIX SYSTEM (1/3)
Seat which does not allow a
²
child seat to be fitted.
Child seat fitted using the ISOFIX
mounting
Seat which allows a ISOFIX or
i-Size child seat to be attached.
±
The front and rear seats are
equipped with an anchorage point al-
lowing a universal forward-facing child
seat ISOFIX to be attached. The an-
choring points are located on the pas-
senger seatback for the front seat and
on the bench seatback for the rear
seats.
Fitting a seat ISOFIX in
the rear-left seat means
the middle seat cannot be
For the front passenger seat, the
used. The central seat belt
Do not fit a child seat when
use of a child seat with a floor sup-
will no longer be either accessible or
the large seat back is in the
port is recommended to avoid trig-
useable.
folded position.
gering the seat belt warning signal.
Using a child safety system
RISK OF DEATH OR
Fit the child seat in a rear
which is not approved for
SERIOUS INJURY:
seat wherever possible.
this vehicle will not correctly
after fitting a rear facing
To install an ISOFIX seat in
protect the baby or child.
child seat on the front pas-
this seat, unbuckle the seat
They risk serious or even fatal injury.
senger seat, check that the airbag
belt by hand before engaging the
has been deactivated
➥ 1.58
bolts.
➥ 1.76.
1.73
CHILD SEATS: attachment using the ISOFIX SYSTEM (2/3)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-
tions in force are respected.
Front passenger seat
Weight of
Size of seat
Rear side
Rear centre
Type of child seat
the child
[fixture]
With airbag
With airbag
seats
seat
disabled
activated
Carrycot
fitted
F, G
across the vehicle
< 10 kg
X
X
IL (2)
X
[L1, L2]
Group 0
Rear-facing shell
E
seat
< 13 kg
IL (1) (3)
X
IL (4)
X
[R1]
Groups 0 or 0 +
Rear-facing seat
< 13 kg and 9 to
C, D
IL (1) (3)
X
IL (4)
X
Groups 0+ and 1
18 kg
[R3, R2]
Forward-facing seat
A, B, B1 [F3,
IUF - IL
IUF - IL
9 to 18 kg
X
X
Group 1
F2, F2X]
(3)
(4) (5)
Booster seat
15 to 25 kg and
IUF - IL
IUF - IL
[B2]
X
X
Groups 2 and 3
22 to 36 kg
(3)
(4) (5)
Seat i-Size
I - U (1) (3)
X
I - U (4) (5)
X
1.74
CHILD SEATS: attachment using the ISOFIX SYSTEM (3/3)
X = Seat not suitable for fitting child seats.
U = Seat allowing a child seat with “Universal” approval to be attached by the seat belt; check that it can be fitted.
IUF/IL = On equipped vehicles, seat which allows a child seat with “Universal/Semi-universal or vehicle-specific” approval to be
fitted using the ISOFIX system; check that it can be fitted.
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
(4) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat
as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the
child seat.
(5) In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting
the child seat. Move the seat in front of the child forwards, move the seatback forward to avoid contact between the seat and
the child's legs.
The size of the ISOFIX child seat is indicated by a letter:
- A, B, B1 [F3, F2,F2X]: for forward-facing seats in Group 1 (9 to 18 kg);
- [B2]: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg);
- C and D [R3 and R2]: rear-facing seats or shell seats in group 0+ (less than 13 kg) or group 1 (9 to 18 kg);
- E [R1]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);
- F, G [L1, L2]: carrycots in group 0 (less than 10 kg).
(1) RISK OF DEATH OR SERIOUS INJURY: after fitting a rear-facing child seat in this seat, make sure that the front
passenger airbag is disabled ➥ 1.58 ➥ 1.76.
1.75
CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3)
The passenger airbag may
1
only be activated or deacti-
2
vated when the vehicle is
stationary with the igni-
tion off.
If it is interfered with when the ve-
hicle is being driven, indicator lights
å
Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.
Deactivating the front
To deactivate the airbag: with the
vehicle stationary and the ignition
passenger airbag
switched off, push and turn lock 1 to
(depending on the vehicle)
the OFF position.
Before installing a child seat on the
When the ignition is switched on, it is
front passenger seat:
DANGER
essential to check that the warning
- check that the child seat can be in-
Since operation of the front
stalled on this seat;
light
¹
is illuminated on the dis-
passenger airbag is not
play 2.
compatible with the po-
- it is essential to deactivate the
sition of a rear-facing child seat,
airbagfor a rear-facing child seat.
This light remains permanently lit to
NEVER fit a rear-facing child re-
let you know that you can fit a child
straint system in a seat protected
seat.
by an ACTIVATED front AIRBAG.
This can lead to the DEATH of the
CHILD or SERIOUS INJURY.
1.76
CHILD SAFETY: deactivating, activating AIRBAG front passenger (2/3)
3
A
A
The markings on the dashboard and
labels A on each side of the passen-
ger sun visor 3 (example: label shown
above) remind you of these instruc-
tions.
DANGER
Since operation of the front
passenger airbag is not
compatible with the po-
sition of a rear-facing child seat,
NEVER fit a rear-facing child re-
straint system in a seat protected
by an ACTIVATED front AIRBAG.
This can lead to the DEATH of the
CHILD or SERIOUS INJURY.
1.77
CHILD SAFETY: deactivating, activating AIRBAG front passenger (3/3)
Operating faults
It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
airbag activation/deactivation system is
1
faulty.
2
Allowing any other passenger to sit in
that seat is not recommended.
Contact your approved dealer as soon
as possible.
Activating the front
To restart the airbag: vehicle
stopped, ignition switched off, press
passenger airbag
and turn the lock to 1 position ON.
(depending on the vehicle)
When the ignition is switched on, you
The passenger airbag may
You should reactivate the airbag as
must check that the warning light
only be activated or deacti-
soon as you remove the child seat from
vated when the vehicle is
the front passenger seat to ensure the
¹
is off and that the warning light
stationary with the igni-
protection of the front passenger in the
tion off.
event of an impact.
lights up on the display 2 after
each start-up for around 1 minute.
If it is interfered with when the ve-
hicle is being driven, indicator lights
The front passenger airbag is activated.
å
Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.
1.78
STEERING WHEEL (1/2)
2
4
3
1
5
Adjusting the steering wheel
Steering wheel heating
Deactivating the function
height and depth
(depending on vehicle)
- Automatic:
Lower the lever 1 and position the
This function heats the steering
The function switches off automatically
steering wheel in the required position.
wheel 4.
after the regulation phase of approxi-
mately 30 minutes.
Then, raise the lever fully, beyond the
Operating principle
point of resistance to lock the steering
- Manually:
When the temperature is reached, the
wheel.
function regulates the temperature of
To deactivate the function during the
Make sure that the steering wheel is
the heated areas for approximately
regulation phase, press the 5 button on
correctly locked.
30 minutes and then switches off auto-
the multimedia screen 2.
matically.
Note: the function is also accessible via
the 3 “Favourites” button on the steer-
Activating the function
ing wheel 4.
With the ignition on, press the 5 button
For safety reasons, only
on the multimedia screen 2.
adjust the steering wheel
when the vehicle is station-
ary.
1.79
STEERING WHEEL (2/2)
Power-assisted steering
The variable power-assisted steering
system is equipped with an electronic
control system which alters the level of
assistance to suit the vehicle speed.
Steering is made easier during parking
manoeuvres (for added comfort) while
the force needed to steer increases
progressively as the speed rises (for
enhanced safety at high speeds).
6
“Favourites” function
Depending on the vehicle, by pressing
the steering wheel control 6, you can
activate the heated steering wheel ac-
cording to the stored use settings that
you have previously defined.
For more information on programming
Never leave the steering wheel on
this function, please refer to the multi-
full lock when the vehicle is station-
media instructions.
ary.
With the engine switched off, or if
there is a system fault, it is still pos-
sible to turn the steering wheel. The
Never switch off the igni-
force required will be greater.
tion when travelling down-
hill, and avoid doing so in
A noise may be heard when the
normal driving (assistance
steering wheel is moved quickly.
is not provided).
This is normal.
1.80
REAR VIEW MIRRORS (1/3)
Electrical folding mirrors
The door mirrors will fold-out automati-
cally when the vehicle is unlocked. The
door mirrors fold in when the vehicle is
locked.
You can deactivate/activate automatic
2
folding of the door mirrors ➥ 1.108.
1
You can force folding by pressing the 1
switch. In this situation, the door mirrors
will remain folded until the 1 button is
pressed again, regardless of automatic
folding.
3
Special case
When the rear view mirror has been
Door mirrors with electrical
manually deployed or folded back, it is
adjustment:
possible to reset it to a usage position.
Select the rear view mirror using on of
To do this, press the 1 switch. A me-
the switches 3, then use the 2 switch to
chanical tapping noise can be heard
adjust it to the desired position.
from the door mirror.
If a tapping noise cannot be heard,
Heated door mirrors
press once again on 1 switch until the
tapping noise can be heard from the
When the engine is started, mirror de-
Objects
observed
in
the
door mirror.
icing is activated with the rear screen
door mirror glass are actu-
de-icing/demisting.
ally closer than they appear.
For your safety, take this
into account in order to correctly
assess the distance before any ma-
For safety reasons, carry
noeuvre.
out any adjustments when
the vehicle is stationary.
1.81
REAR VIEW MIRRORS (2/3)
Returning to the driving
Recalling the memorised
position
position
Moving from reverse gear to a forward
Refer to the multimedia manual to
gear is done:
access recall of the saved position.
– approximately 9 seconds after re-
Select “ Call back”.
verse gear has been disengaged
The positions of the door mirrors in
2
when the speed is lower than 6 mph
forward gear, reverse and of the front
(10 km/h);
seats are recalled.
- forward gear engaged when
the speed is greater than 6 mph
(10 km/h);
- when the engine is stopped.
3
Position memory
Rear view mirrors which tilt
in reverse gear
- Adjust the door mirrors (see previous
paragraphs);
For vehicles equipped with the driver’s
- refer to the multimedia instructions
seat with position memory, you can
to access the settings memory. Save
enter a specific setting for the door mir-
the settings.
rors when reversing and store the po-
sition.
The positions of the door mirrors in
forward and reverse gear, and the po-
With the vehicle stationary and reverse
sition of the driver’s seat are saved si-
gear engaged, select the rear view
multaneously.
mirror using one of the switches 3 then,
with the 2 switch, adjust it to the re-
quired position.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
1.82
REAR VIEW MIRRORS (3/3)
5
4
Interior rear view mirror
Auto-dimming rear view mirror 5
Its position can be adjusted.
The rear view mirror automatically dark-
ens when you are being followed by a
Rear view mirror with lever 4
vehicle using main beam headlights or
in very bright lighting.
When driving at night, to avoid being
dazzled by the headlights of the vehicle
Camera rear view
behind, depress the little lever located
behind rear view mirror 4.
Depending on the vehicle, your rear
view mirror may be fitted with a dis-
play of the rear surroundings transmit-
ted by the camera fitted behind the rear
screen.
For more information ➥ 1.84.
1.83

 

 

 

 

 

 

 

Content      ..     2      3      4      5     ..