Content .. 8 9 10 11 ..

Nissan Rogue Sport (2022 year). Manual in english - page 10

2-72

Instruments and controls

JVI0619X

SUNGLASSES HOLDER

WARNING

Keep the sunglasses holder closed

while driving to avoid obstructing

the driver’s view and to help prevent

an accident.

CAUTION

Do not use for anything other

than sunglasses.

Do not leave sunglasses in the

sunglasses holder while parking

in direct sunlight. The heat may

damage the sunglasses.

To open the sunglasses holder, push and

release. Only store one pair of sunglasses

in the holder.

SIC4348

CARD HOLDER (driver’s side)

Slide a card in the card holder.

JVI1686X

Cargo area

LUGGAGE HOOKS

To use the hook, pull it up as illustrated.

WARNING

Always make sure that the cargo

is properly secured. Use the sui-

table ropes and hooks.

Unsecured cargo can become

dangerous in an accident or sud-

den stop.

Do not apply a total load of more

than 22 lb (10 kg) to a single hook.

JVI1336X

Cargo area (hooks for shopping bags, etc.)

WARNING

Do not apply a total load of more

than 7 lb (3 kg) to the hook.

JVI1334X

PARCEL SHELF (if so equipped)

WARNING

Never put anything on the parcel

shelf, no matter how small. Any

object on it could cause an injury

in case of an accident or if the

brakes are applied suddenly.

Do not leave the parcel shelf in

position when it is disengaged

from the grooves.

Properly secure all cargo to help

prevent it from sliding or shifting.

Do not place cargo higher than

Instruments and controls

2-73

2-74

Instruments and controls

the seatbacks. In a sudden stop

or collision, unsecured cargo

could cause personal injury

The child restraint top tether

strap may be damaged by con-

tact with the parcel shelf or items

in the cargo area. Remove the

parcel shelf from the vehicle or

store it in its storage space. Also,

secure any lose items in the cargo

area. Your child could be seriously

injured or killed in a collision if the

top tether strap is damaged.

Removal

1. Open the liftgate. (See “Liftgate” (P.3-

26).)

2. Detach both of the ropes (left and

right)

from the inside of the liftgate.

3. Detach the parcel shelf by simply

pulling it rearwards through the lift-

gate opening.

JVI1335X

CAUTION

Make sure the parcel shelf is care-

fully stored when not in use in order

to prevent any damage.

Installation

1. Open the liftgate.
2. Insert the parcel shelf by pushing it

forwards as far as possible through

the liftgate opening.

3. Attach the corresponding ropes to

each side

of the liftgate.

4. Close the liftgate.

JVI0889X

Do not apply any load directly to the roof

side rails. Cross bars must be installed

before applying load/cargo/luggage to

the roof of the vehicle. Genuine NISSAN

accessory cross bars are available

through a NISSAN dealer. It is recom-

mended that you visit a NISSAN dealer for

additional information.
The service load capacity for the roof side

rails is 150 lb (68 kg), however do not

exceed the accessory cross bars load

capacity.
Be careful that your vehicle does not

exceed the Gross Vehicle Weight Rating

(GVWR) or its Gross Axle Weight Rating

(GAWR front and rear). The GVWR and

GAWR are located on the F.M.V.S.S. or C.V.

M.S.S. certification label (located on the

driver’s door pillar). For additional infor-

mation regarding GVWR and GAWR, refer

to “Vehicle loading information” (P.10-12).

WARNING

Always install the cross bars onto

the roof side rails before loading

cargo of any kind. Loading cargo

directly onto the roof side rails or

the vehicle’s roof may cause ve-

hicle damage.

Drive extra carefully when the

vehicle is loaded at or near the

cargo carrying capacity, espe-

cially if the significant portion of

that load is carried on the cross

bars.

Heavy loading of the cross bars

has the potential to affect the

vehicle stability and handling

during sudden or unusual hand-

ling maneuvers.

Roof rack cross bars should be

evenly distributed.

Do not exceed maximum roof

rack cross bars load.

Properly secure all cargo with

ropes or straps to help prevent it

from sliding or shifting. In a sud-

den stop or collision, unsecured

cargo could cause personal in-

jury.

Instruments and controls

2-75

ROOF RACK (if so equipped)

2-76

Instruments and controls

POWER WINDOWS

WARNING

Make sure that all passengers

have their hands, etc. inside the

vehicle while it is in motion and

before closing the windows. Use

the window lock switch to pre-

vent unexpected use of the

power windows.

To help avoid risk of injury or

death through unintended opera-

tion of the vehicle and or its

systems, including entrapment

in windows or inadvertent door

lock activation, do not leave chil-

dren, people who require the

assistance of others or pets un-

attended in your vehicle. Addi-

tionally, the temperature inside a

closed vehicle on a warm day can

quickly become high enough to

cause a significant risk of injury

or death to people and pets.

The power windows operate when the

ignition switch is in the ON position, or for

about 45 seconds after the ignition

switch is placed in the OFF position. If

the driver’s or front passenger’s door is

opened during this period of about 45

seconds, power to the windows is can-

celed.

SIC4533

Window lock button

Driver side window

Rear left passenger side window

Front passenger side window

Rear right passenger side window

Main power window switch (driver’s

side)

To open or close the window, push down

or pull up

the switch and hold it. The

main switch (driver side switches) will

open or close all the windows.

WINDOWS

Locking passengers’ windows

When the lock button

is pushed in, only

the driver side window can be opened or

closed. Push it in again to cancel.

SIC4523

Passenger side power window

switch

The passenger side switch will open or

close only the corresponding window. To

open or close the window, push down or

pull up the switch and hold it.

SIC4524

Automatic operation

The automatic operation is available for

the switch that has an

mark on its

surface.
To fully open or close the window, com-

pletely push down or pull up the switch

and release it; the switch need not be

held. The window will automatically open

or close all the way. To stop the window,

just push or lift the switch in the opposite

direction.
A light push or pull on the switch will

cause the window to open or close until

the switch is released.

Instruments and controls

2-77

2-78

Instruments and controls

Auto-reverse function

WARNING

There are some small distances im-

mediately before the closed position

which cannot be detected. Make sure

that all passengers have their hands,

etc., inside the vehicle before closing

the window.

If the control unit detects something

caught in the window as it is closing, the

window will be immediately lowered.
The auto reverse function can be acti-

vated when the window is closed by

automatic operation when the ignition

switch is in the ON position or for 45

seconds after the ignition switch is placed

in the OFF position.

Depending on the environment or driv-

ing conditions, the auto reverse func-

tion may be activated if an impact or

load similar to something being caught

in the window occurs.

If the windows do not close auto-

matically

If the power window automatic function

(closing only) does not operate properly,

perform the following procedure to initi-

alize the power window system.
1. Start the engine.
2. Close the door.
3. After starting the engine, open the

window completely by operating the

power window switch.

4. Pull the power window switch and

hold it to close the window, and then

hold the switch more than 3 seconds

after the window is closed completely.

5. Release the power window switch.

Operate the window by the automatic

function to confirm the initialization is

complete.

If the power window automatic function

does not operate properly after perform-

ing the procedure above, it is recom-

mended you have your vehicle checked

by a NISSAN dealer.

WARNING

In an accident you could be

thrown from the vehicle through

an open moonroof. Always use

seat belts and child restraints.

Do not allow anyone to stand up

or extend any portion of their

body out of the moonroof open-

ing while the vehicle is in motion

or while the moonroof is closing.

CAUTION

Remove water drops, snow, ice or

sand from the moonroof before

opening.

Do not place any heavy object on

the moonroof or surrounding

area.

POWER MOONROOF

The moonroof only operates when the

ignition switch is in the ON position.
The moonroof is operational for about 45

seconds, even if the ignition switch is

pushed to the OFF position. If the driver’s

door or the passenger’s door is opened

MOONROOF (if so equipped)

during this period of about 45 seconds,

power to the moonroof is canceled.

JVI0655X

Sunshade

The sunshade will open automatically

when the moonroof is opened. However,

it must be closed manually.

Tilting the moonroof

To tilt up, first close the moonroof, then

push the switch to the tilt up position

and release it; it need not be held. To tilt

down the moonroof, push the switch to

the tilt down position

Sliding the moonroof

To fully open or close the moonroof, push

the switch to the open

or close

position and release it; it need not be held.

The roof will automatically open or close

all the way. To stop the roof, push the

switch once more while it is opening or

closing.

Auto reverse function

WARNING

There are some small distances im-

mediately before the closed position

which cannot be detected. Make sure

that all passengers have their hands,

etc., inside the vehicle before closing

the moonroof.

If the control unit detects something

caught in the moonroof when it is closing,

the moonroof will be immediately

opened.
The auto reverse function can be acti-

vated when the moonroof is closed by

automatic operation when the ignition

switch is in the ON position or for about

45 seconds after the ignition switch is

pushed to the OFF position.
If the moonroof cannot be closed auto-

Instruments and controls

2-79

2-80

Instruments and controls

matically when the auto reverse function

activates due to a malfunction, push and

hold the moonroof switch to the close

position

Depending on the environment or driv-

ing conditions, the auto reverse func-

tion may be activated if an impact or

load similar to something being caught

in the moonroof occurs.

If the moonroof does not operate

If the moonroof does not operate prop-

erly, perform the following procedure to

initialize the moonroof operation system.
1. If the moonroof is open, close it fully

by repeatedly pushing the moonroof

switch to the close position

to tilt

the moonroof up.

2. Push and hold the switch to the close

position

3. Release the moonroof switch after the

moonroof moves slightly up and

down.

4. Push and hold the switch to the open

position

to fully tilt the moonroof

down.

5. Check if the moonroof switch oper-

ates normally.

If the moonroof does not operate prop-

erly after performing the procedure

above, have your moonroof checked and

repaired. It is recommended you visit a

NISSAN dealer for this service.

CAUTION

Do not leave the light switch on

when the engine is not running

for extended periods of time to

prevent the battery from being

discharged.

Turn off the lights when you leave

the vehicle.

INTERIOR LIGHTS

JVI0626X

INTERIOR LIGHT SWITCH

The interior light can be turned ON

regardless of door position. The light will

go off after a period of time unless the

ignition switch is placed in the ON posi-

tion when any door is opened.
The interior lights can be set to operate

when the doors are opened. To turn off

the interior lights when a door open, push

the switch, the interior lights will not

illuminate, regardless of door position.

The lights will go off when the ignition

switch is placed in the ON position, or the

driver’s door is closed and locked. The

lights will also go off after a period of time

when the doors are open.

JVI0627X

CONSOLE LIGHT (if so equipped)

The console light will turn on whenever

the parking lights or headlights are illu-

minated.

JVI0628X

MAP LIGHTS

Push the button to turn the map lights

on. To turn them off, push the button

again.

Instruments and controls

2-81

2-82

Instruments and controls

SIC2063A

ROOM LIGHT

The room light has a three-position

switch.
When the switch is in the ON position

the room light illuminates.
When the switch is in the DOOR position

, the room light illuminates when a door

is opened.
The interior light timer will keep the room

light on for approximately 15 seconds

when:

The key is removed from the ignition

switch with the driver’s door closed.

(model without Intelligent Key system)

The ignition switch is placed in the

OFF position. (model with Intelligent

Key system)

The interior light timer will be cancelled

when:

The driver’s door is locked.

The ignition switch is placed in the ON

position.

When the switch is in the OFF position

the room light does not illuminate, re-

gardless of any condition.

SIC3869

VANITY MIRROR LIGHT (if so

equipped)

The light on the vanity mirror will turn on

when the cover on the vanity mirror is

opened.
When the cover is closed, the light will

turn off.

The lights will also turn off after a

period of time when the lights remain

illuminated to prevent the battery from

becoming discharged.

CARGO LIGHT

The cargo lights illuminate when the

liftgate is opened. When the liftgate is

closed, the lights will turn off.

The light will also turn off after a period

of time when the light remains illumi-

nated after the ignition switch has been

pushed to the OFF position to prevent

the battery from becoming discharged.

The HomeLink® Universal Transceiver

provides a convenient way to consolidate

the functions of up to three individual

hand-held transmitters into one built-in

device.
HomeLink® Universal Transceiver:

Will operate most Radio Frequency

(RF) devices such as garage doors,

gates, home and office lighting, entry

door locks and security systems.

Is powered by your vehicle’s battery.

No separate batteries are required. If

the vehicle’s battery is discharged or is

disconnected, HomeLink® will retain

all programming.

When the HomeLink® Universal Trans-

ceiver is programmed, retain the origi-

nal transmitter for future programming

procedures (Example: new vehicle pur-

chases). Upon sale of the vehicle, the

programmed HomeLink® Universal

Transceiver buttons should be erased

for security purposes. For additional

information, refer to “Programming

HomeLink®” (P.2-84).

WARNING

Do not use the HomeLink® Uni-

versal Transceiver with any gar-

age door opener that lacks safety

stop and reverse features as re-

quired by federal safety stan-

dards. (These standards became

effective for opener models man-

ufactured after April 1, 1982.) A

garage door opener which cannot

detect an object in the path of a

closing garage door and then

automatically stop and reverse,

does not meet current federal

safety standards. Using a garage

door opener without these fea-

tures increases the risk of serious

injury or death.

During the programming proce-

dure your garage door or security

gate will open and close (if the

transmitter is within range). Make

sure that people or objects are

clear of the garage door, gate,

etc. that you are programming.

Your vehicle’s engine should be

turned off while programming

the HomeLink® Universal Trans-

ceiver. Do not breathe exhaust

gases; they contain colorless

and odorless carbon monoxide.

Carbon monoxide is dangerous. It

can cause unconsciousness or

death.

Instruments and controls

2-83

HomeLink® UNIVERSAL

TRANSCEIVER (if so equipped)

2-84

Instruments and controls

PROGRAMMING HomeLink®

The following steps show generic instruc-

tions how to program a HomeLink®

button. If you have any questions or are

having difficulty programming your

HomeLink® buttons, refer to the

HomeLink® web site at: www.homelink.

com/nissan or call 1-800-355-3515.

NOTE:
It is also recommended that a new

battery be placed in the hand-held

transmitter of the device being pro-

grammed to HomeLink® for quicker

programming and accurate transmis-

sion of the radio-frequency.

1. Position the end of your hand-held

transmitter 1-3 in (26-76 mm) away

from the HomeLink® surface, keeping

the HomeLink® indicator light

view.

JVI0428X

2. Using both hands, simultaneously

press and hold the desired HomeLink®

button and handheld transmitter but-

ton. DO NOT release until the

HomeLink® indicator light

flashes

slowly and then rapidly. When the

indicator light flashes rapidly, both

buttons may be released. (The rapid

flashing indicates successful pro-

gramming.)

NOTE:

Some devices to be programmed

may require you to replace Step 2

with the cycling procedure noted in

the “Programming HomeLink® for

Canadian customers and gate open-

ers” (P.2-85).

JVI0429X

3. Press and hold the programmed

HomeLink® button and observe the

indicator light.

If the indicator light

is solid/

continuous, programming is com-

plete and your device should acti-

vate when the HomeLink® button is

pressed and released.

If the indicator light

blinks rapidly

for two seconds and then turns to a

solid/continuous light, continue

with Steps 4-6 for a rolling code

device. A second person may make

the following steps easier. Use a

ladder or other device. Do not stand

on your vehicle to perform the next

steps.

4. At the receiver located on the garage

door opener motor in the garage,

locate the “learn” or “smart” button

(the name and color of the button

may vary by manufacturer but it is

usually located near where the hang-

ing antenna wire is attached to the

unit). If there is difficulty locating the

button, reference the garage door

opener’s manual.

5. Press and release the “learn” or “smart”

button.

NOTE:

Once the button is pressed, you have

approximately 30 seconds to initiate

the next step.

6. Return to the vehicle and firmly press

and hold the programmed HomeLink®

button for two seconds and release.

Repeat the “press/hold/release” se-

quence up to 3 times to complete

the programming process. HomeLink®

should now activate your rolling code

equipped device.

7. If you have any questions or are

having difficulty programming your

HomeLink® buttons, refer to the

HomeLink® web site at: www.

homelink.com/nissan or call 1-800-

355-3515.

PROGRAMMING HomeLink® FOR

CANADIAN CUSTOMERS AND GATE

OPENERS

Canadian radio-frequency laws require

transmitter signals to “time-out” (or quit)

after several seconds of transmission –

which may not be long enough for

HomeLink® to pick up the signal during

programming. Similar to this Canadian

law, some U.S. gate operators are de-

signed to “time-out” in the same manner.
If you live in Canada or you are having

difficulties programming a gate operator

or garage door opener by using the

“Programming HomeLink®” procedures,

replace “Programming HomeLink®” Step

2 with the following:

NOTE:
When programming a garage door

opener, etc., unplug the device during

the “cycling” process to prevent possi-

ble damage to the garage door opener

components.

Step 2: Using both hands, simultaneously

press and hold the desired HomeLink®

button and the hand-held transmitter

button. During programming, your hand-

held transmitter may automatically stop

transmitting. Continue to press and hold

the desired HomeLink® button while you

press and re-press (“cycle”) your hand-

held transmitter every two seconds until

the frequency signal has been learned.

The HomeLink® indicator light will flash

slowly and then rapidly after several

seconds upon successful programming.

DO NOT

release until the HomeLink®

indicator light flashes slowly and then

rapidly. When the indicator light flashes

rapidly, both buttons may be released.

The rapid flashing indicates successful

programming.
Proceed with “Programming HomeLink®”

step 3 to complete.
Remember to plug the device back in

when programming is completed.

OPERATING THE HomeLink® UNI-

VERSAL TRANSCEIVER

The HomeLink® Universal Transceiver,

after it is programmed, can be used to

activate the programmed device. To op-

erate, simply press and release the appro-

priate programmed HomeLink® Universal

Transceiver button. The amber indicator

light will illuminate while the signal is

being transmitted.
For convenience, the hand-held transmit-

ter of the device may also be used at any

time.

Instruments and controls

2-85

2-86

Instruments and controls

PROGRAMMING TROUBLESHOOT-

ING

If the HomeLink® does not quickly learn

the hand-held transmitter information:

replace the hand-held transmitter

batteries with new batteries.

position the hand-held transmitter

with its battery area facing away from

the HomeLink® surface.

press and hold both the HomeLink®

and hand-held transmitter buttons

without interruption.

position the hand-held transmitter 1-3

in (26-76 mm) away from the

HomeLink® surface. Hold the transmit-

ter in that position for up to 15

seconds. If HomeLink® is not pro-

grammed within that time, try holding

the transmitter in another position -

keeping the indicator light in view at

all times.

If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site

at: www.homelink.com/nissan or 1-800-

355-3515.

CLEARING THE PROGRAMMED IN-

FORMATION

The following procedure clears the pro-

grammed information from both buttons.

Individual buttons cannot be cleared.

However, individual buttons can be re-

programmed, see “Reprogramming a sin-

gle HomeLink® button” (P.2-86).

To clear all programming

1. Press and hold the two outer

HomeLink® buttons until the indicator

light begins to flash in approximately

10 seconds. Do not hold for longer

than 20 seconds.

2. Release both buttons.
HomeLink® is now in the programming

mode and can be programmed at any

time beginning with “Programming

HomeLink®” - Step 1.

REPROGRAMMING A SINGLE

HomeLink® BUTTON

To reprogram a HomeLink® Universal

Transceiver button, complete the follow-

ing.
1. Press and hold the desired HomeLink®

button.

Do not

release the button.

2. The indicator light will begin to flash

after 20 seconds. Without releasing

the HomeLink® button, proceed with

“Programming HomeLink®” - Step 1.

For questions or comments, contact

HomeLink® at: www.homelink.com/

nissan or 1-800-355-3515.
The HomeLink® Universal Transceiver

button has now been reprogrammed.

The new device can be activated by

pushing the HomeLink® button that was

just programmed. This procedure will not

affect any other programmed HomeLink®

buttons.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should

change the codes of any non-rolling code

device that has been programmed into

HomeLink®. Consult the Owner’s Manual

of each device or call the manufacturer or

dealer of those devices for additional

information.

When your vehicle is recovered, you will

need to reprogram the HomeLink® Uni-

versal Transceiver with your new trans-

mitter information.
FCC Notice:
For USA:
This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference,

and (2) this device must accept any

interference received, including inter-

ference that may cause undesired op-

eration.
NOTE:
Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s

authority to operate the equipment.
For Canada:
This device complies with Industry Ca-

nada licence-exempt RSS standard(s).

Operation is subject to the following

two conditions: (1) this device may not

cause interference, and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

Instruments and controls

2-87

Content .. 8 9 10 11 ..