Nissan Titan (2022 year). Manual in english - page 23

BSW SYSTEM OPERATION

The BSW system operates above approxi-
mately 20 mph (32 km/h).

If the radar sensors detect a vehicle in the
detection zone, the side BSW/RCTA indica-
tor light (1) illuminates. If the turn signal is
then activated, the system chimes (twice)
and the side BSW/RCTA indicator light
flashes and the BSW/RCTA indicator illumi-
nates (yellow) in the vehicle information
display. The side BSW/RCTA indicator light
continues to flash until the detected ve-
hicle leaves the detection zone.

The side BSW/RCTA indicator light illumi-
nates for a few seconds when the ignition
switch is placed in the ON position.

The brightness of the side BSW/RCTA indi-
cator light is adjusted automatically de-
pending on the brightness of the ambient
light.

If a vehicle comes into the detection zone
after the driver activates the turn signal,
then only the side BSW/RCTA indicator light
flashes and no chime sounds. For addi-
tional information, see “BSW driving situa-
tions” (P. 5-36).

HOW TO ENABLE/DISABLE THE
BSW SYSTEM

LSD3733

5-34

Starting and driving

When the BSW system is enabled in the
vehicle information display, the system can
be turned off temporarily by pushing the
warning systems switch. For additional in-
formation, see “Warning systems switch”
(P. 2-57).

Perform the following steps to enable or
disable the BSW system:

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance” and press ENTER.

2. Select “Blind Spot” and press ENTER.

3. Select “Warning (BSW)” and press ENTER.

4. Push the Warning systems switch to

turn the system on or off.

NOTE:
• When enabling/disabling the system,

the system will retain current settings
even if the engine is restarted.

• When the BSW system is turned on, the

BSW/RCTA indicator (white) in the ve-
hicle information display illuminates.

BSW SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the BSW system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

•

The BSW system cannot detect all ve-
hicles under all conditions.

•

The radar sensors may not be able to
detect and activate BSW when cer-
tain objects are present such as:

–

Pedestrian, bicycles, animals.

–

Vehicles such as motorcycles, low

height vehicles, or high ground
clearance vehicles.

–

Oncoming vehicles.

–

Vehicles remaining in the detec-

tion zone when you accelerate
from a stop.

–

A vehicle merging into an adjacent

lane at a speed approximately the
same as your vehicle.

–

vehicle

approaching

rapidly

from behind.

–

A vehicle which your vehicle over-

takes rapidly.

–

A vehicle that passes through the

detection zone quickly.

–

When overtaking several vehicles

in a row, the vehicles after the first
vehicle may not be detected if
they are traveling close together.

•

The radar sensor’s detection zone is
designed based on a standard lane
width. When driving in a wider lane,
the radar sensors may not detect ve-
hicles in an adjacent lane. When driv-
ing in a narrow lane, the radar sen-
sors may detect vehicles driving two
lanes away.

•

The radar sensors are designed to ig-
nore most stationary objects; how-
ever, objects such as guardrails,
walls, foliage and parked vehicles
may occasionally be detected. This is
a normal operation condition.

•

The following conditions may reduce
the ability of the radar to detect other
vehicles:

–

Severe weather

–

Road spray

–

Ice/frost/snow/dirt build-up on

the vehicle

Starting and driving

5-35

•

Do not attach stickers (including
transparent material), install acces-
sories or apply additional paint near
the radar sensors. These conditions
may reduce the ability of the radar to
detect other vehicles.

•

Excessive noise (for example, audio
system volume, open vehicle win-
dow) will interfere with the chime
sound, and it may not be heard.

BSW DRIVING SITUATIONS

Indicator on

Indicator off

Indicator flashing

Another vehicle approaching
from behind

Illustration 1:

The side BSW/RCTA indicator

light illuminates if a vehicle enters the de-
tection zone from behind in an adjacent
lane.

NOTE:
• The radar sensors may not detect ve-

hicles which are approaching rapidly
from behind.

LSD2299

Illustration 1 – Approaching from behind

5-36

Starting and driving

Illustration 2:

If the driver activates the

turn signal when another vehicle is in the
detection zone, then the system chimes
(twice) and the side BSW/RCTA indicator
light flashes.

NOTE:
• The radar sensors may not detect ve-

hicles which are approaching rapidly
from behind.

• If the driver activates the turn signal

before a vehicle enters the detection
zone, the side BSW/RCTA indicator
light will flash but no chime will sound
when the other vehicle is detected.

Overtaking another vehicle

Illustration 3:

The side BSW/RCTA indica-

tor light illuminates if you overtake a ve-
hicle and that vehicle stays in the detection
zone for approximately 2 seconds.

LSD2300

Illustration 2 – Approaching from

behind

LSD2302

Illustration 3 – Overtaking another

vehicle

Starting and driving

5-37

Illustration 4:

If the driver activates the

turn signal while another vehicle is in the
detection zone, then the system chimes
(twice) and the side BSW/RCTA indicator
light flashes.

NOTE:
• When overtaking several vehicles in a

row, the vehicles after the first vehicle
may not be detected if they are travel-
ing close together.

• The radar sensors may not detect

slower moving vehicles if they are
passed quickly.

• If the driver activates the turn signal

before a vehicle enters the detection
zone, the side BSW/RCTA indicator
light will flash but no chime will sound
when the other vehicle is detected.

Entering from the side

Illustration 5:

The side BSW/RCTA indicator

light illuminates if a vehicle enters the de-
tection zone from either side.

LSD2303

Illustration 4 – Overtaking another

vehicle

LSD2305

Illustration 5 – Entering from the side

5-38

Starting and driving

Illustration 6:

If the driver activates the

turn signal while another vehicle is in the
detection zone, then the system chimes
(twice) and the side BSW/RCTA indicator
light flashes.

NOTE:
• If the driver activates the turn signal

before a vehicle enters the detection
zone, the side BSW/RCTA indicator
light will flash but no chime will sound
when the other vehicle is detected.

• The radar sensors may not detect a ve-

hicle which is traveling at about the
same speed as your vehicle when it en-
ters the detection zone.

LSD2308

Illustration 6 – Entering from the side

Starting and driving

5-39

SYSTEM TEMPORARILY DISABLED

When radar blockage is detected, the sys-
tem will be deactivated automatically. The

“Unavailable:

Side

Radar

Obstruction”

warning message will appear and the
BSW/RCTA indicator (white) will blink

the vehicle information display.

The system is not available until the condi-
tions no longer exist.

The radar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog. The blocked condi-
tion may also be caused by objects such as
ice, frost or dirt obstructing the radar
sensors.

NOTE:

If the BSW system stops working, the
RCTA system will also stop working.

Action to take:

When the above conditions no longer exist,
the system will resume automatically.

Malfunction

If the BSW system malfunctions, it will turn
off automatically. The system malfunction
warning message with the BSW/RCTA indi-
cator (orange) will appear in the vehicle in-
formation display.

NOTE:

If the BSW system stops working, the
RCTA system will also stop working.

LSD3710

5-40

Starting and driving

Action to take:

Stop the vehicle in a safe location, place the
vehicle in the P (Park) position, turn the en-
gine off and restart the engine. If the mes-
sage continues to appear, have the system
checked. It is recommended that you visit a
NISSAN dealer for this service.

SYSTEM MAINTENANCE

The two radar sensors

for the BSW and

RCTA systems are located near the rear
bumper. Always keep the area near the ra-
dar sensors clean.

The radar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog.

The blocked condition may also be caused
by objects such as ice, frost or dirt ob-
structing the radar sensors.

Check for and remove objects obstructing
the area around the radar sensors.

Do not attach stickers (including transpar-
ent material), install accessories or apply
additional paint near the radar sensors.

Do not strike or damage the area around
the radar sensors. It is recommended that
you visit a NISSAN dealer if the area around
the radar sensors is damaged due to a
collision.

Radio frequency statement

For USA

FCC ID: OAYSRR3B

This device complies with Part 15 of the
FCC Rules.

Operation is subject to the following two
conditions:

This device may not cause harmful in-
terference, and

This device must accept any interfer-
ence received, including interference
that may cause undesired operation.

FCC Warning

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

LSD2619

Starting and driving

5-41

WARNING

Failure to follow the warnings and in-
structions for proper use of the RCTA
system could result in serious injury or
death.

•

The RCTA system is not a replace-
ment for proper driving procedures
and is not designed to prevent con-
tact with vehicles or objects. When
backing out of a parking space, al-
ways use the side and rear mirrors
and turn and look in the direction
your vehicle will move. Never rely
solely on the RCTA system.

•

Do not use the RCTA system when
towing a trailer. The system may not
function properly.

The RCTA system will assist you when
backing out from a parking space. When
the vehicle is in reverse, the system is de-
signed to detect other vehicles approach-
ing from the right or left of the vehicle. If the
system detects cross traffic, it will alert you.

RCTA SYSTEM OPERATION

1. Side BSW/RCTA Indicator Light

2. BSW/RCTA Indicator

The RCTA system can help alert the driver
of an approaching vehicle when the driver
is backing out of a parking space.

LSD3933

REAR CROSS TRAFFIC ALERT (RCTA)

5-42

Starting and driving

When the shift position is in R (Reverse) and
the vehicle speed is less than approxi-
mately 5 mph (8 km/h), the RCTA system is
operational.

If the radar detects an approaching vehicle
from the side, the system chimes a sound
(single beep) and the side BSW/RCTA indi-
cator light on the side of the vehicle is ap-
proaching from flashes.

The RCTA system uses radar sensors

installed on both sides near the rear bum-
per to detect an approaching vehicle.

The radar sensors

can detect an ap-

proaching vehicle from up to approxi-
mately 66 ft (20 m) away.

LSD2216

LSD2619

Starting and driving

5-43

HOW TO ENABLE/DISABLE THE
RCTA SYSTEM

When the RCTA system is enabled in the
vehicle information display, the system can
be turned off temporarily by pushing the
Front and rear sonar system OFF switch.
For additional information, see “Parking
Aids system switch” (P. 2-62).

Perform the following steps to enable or
disable the RCTA system:

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance” and press ENTER.

2. Select “Parking Aids” and press ENTER.

3. Select “CTA” and press the ENTER button

to turn system on or off.

4. Push the Parking Aids system switch to

turn the system on or off.

NOTE:

When enabling/disabling the system,
the system setting will be retained even
if the engine is restarted.

LSD3734

5-44

Starting and driving

RCTA SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the RCTA system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

•

Always check surroundings and turn
to check what is behind you before
backing up. The radar sensors detect
approaching (moving) vehicles. The
radar sensors cannot detect every
object such as:

–

Pedestrians,

bicycles,

motor-

cycles, animals or child-operated
toy vehicles

–

A vehicle that is passing at speeds

greater than approximately 19
mph (30 km/h)

–

A vehicle that is passing at speeds

lower than approximately 5 mph
(8 km/h)

•

The radar sensors may not detect
approaching vehicles in certain situ-
ations:

–

Illustration

: When a vehicle

parked next to you obstructs the
beam of the radar sensor.

–

Illustration

: When the vehicle is

parked

angled

parking

space.

–

Illustration

: When the vehicle is

parked on inclined ground.

–

Illustration

When

ap-

proaching vehicle turns into your
vehicle's parking lot aisle.

LSD3195

Starting and driving

5-45

–

Illustration

: When the angle

formed by your vehicle and ap-
proaching vehicle is small.

•

The following conditions may reduce
the ability of the radar to detect other
vehicles:

–

Severe weather

–

Road spray

–

Ice/frost/snow/dirt build-up on

the vehicle

•

Excessive noise (e.g., audio system
volume, open vehicle window) will in-
terfere with the chime sound, and it
may not be heard.

NOTE:

In the case of several vehicles approach-
ing in a row (Illustration 1) or in the oppo-
site direction (Illustration 2), a chime may
not be sounded by the RCTA system af-
ter the first vehicle passes the sensors.

LSD2043

Illustration 1

LSD2044

Illustration 2

5-46

Starting and driving

SYSTEM TEMPORARILY
UNAVAILABLE

When radar blockage is detected, the sys-
tem will be deactivated automatically. The
“Unavailable

Side

Radar

Obstruction”

warning message will appear and the
BSW/RCTA indicator (white) will blink

the vehicle information display.

The systems are not available until the
conditions no longer exist.

The radar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog.

The blocked condition may also be caused
by conditions such as ice, frost or dirt ob-
structing the radar sensors.

NOTE:
If the BSW system stops working, the
RCTA system will also stop working.

Action to take

When the above conditions no longer exist,
the system will resume automatically.

LSD3710

Starting and driving

5-47

Malfunction

When the RCTA system malfunctions, it will
turn off automatically. The system mal-
function warning message with the BSW/
RCTA indicator (orange) will appear in the
vehicle information display.

NOTE:

If the BSW system stops working, the
RCTA system will also stop working.

Action to take

SYSTEM MAINTENANCE

The two radar sensors

for the BSW and

RCTA systems are located near the rear
bumper. Always keep the area near the ra-
dar sensors clean.

The radar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog.

The blocked condition may also be caused
by objects such as ice, frost or dirt ob-
structing the radar sensors.

Check for and remove objects obstructing
the area around the radar sensors.

Do not attach stickers (including transpar-
ent material), install accessories or apply
additional paint near the radar sensors.

Do not strike or damage the area around
the radar sensors. It is recommended that
you visit a NISSAN dealer if the area around
the radar sensors is damaged due to a
collision.

Radio frequency statement

For USA

FCC ID: OAYSRR3B

This device complies with Part 15 of the
FCC Rules.

Operation is subject to the following two
conditions:

This device may not cause harmful
interference, and

This device must accept any interfer-
ence received, including interference
that may cause undesired operation.

FCC Warning

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the equipment.

LSD2619

5-48

Starting and driving

PRECAUTIONS ON CRUISE
CONTROL

1. CANCEL switch

2. ACCEL/RES switch

3. COAST/SET switch

4. ON/OFF switch
• If the cruise control system malfunctions,

it cancels automatically. The

(green)

indicator illuminates in the vehicle infor-
mation display then blinks to warn the
driver.

• If the

(green) indicator blinks, push

the ON/OFF switch off and have the sys-
tem checked. It is recommended that
you visit a NISSAN dealer for this service.

• The

(green) indicator may blink

when the ON/OFF switch is pushed ON
while pushing the ACCEL/RES, COAST/
SET, or CANCEL switch. To properly set the
cruise control system, use the following
procedures.

WARNING

Do not use the cruise control when driv-
ing under the following conditions:

•

When it is not possible to keep the
vehicle at a set speed.

•

In heavy traffic or in traffic that varies
in speed.

•

On winding or hilly roads.

•

On slippery roads (rain, snow, ice,
etc.).

•

In very windy areas.

Doing so could cause a loss of vehicle
control and result in an accident.

CRUISE CONTROL OPERATIONS

The cruise control allows driving at a speed
between 25 - 89 mph (40 - 144 km/h) with-
out keeping your foot on the accelerator
pedal.

To turn on the cruise control,

push the

ON/OFF switch on. The

(white) indica-

tor in the vehicle information display will
illuminate.

To set cruising speed,

accelerate the ve-

hicle to the desired speed, push the
COAST/SET switch and release it. The

(green) indicator in the vehicle infor-

mation display will illuminate. Take your
foot off the accelerator pedal. Your vehicle
maintains the set speed.
•

To pass another vehicle,

depress the ac-

celerator pedal. When you release the
pedal, the vehicle returns to the previ-
ously set speed.

• The vehicle may not maintain the set

speed when going up or down steep hills.
If this happens, drive without the cruise
control.

LSD2464

CRUISE CONTROL (if so equipped)

Starting and driving

5-49

Content .. 21 22 23 24 ..