Nissan Frontier D40. Manual - part 395

 

  Index      Nissan     Nissan Frontier D40 (2010 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  393  394  395  396   ..

 

 

Nissan Frontier D40. Manual - part 395

 

 

P0500 VSS

EC-271

< COMPONENT DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

6.

Check 1st trip DTC.

7.

If 1st trip DTC is detected, go to 

EC-271, "Diagnosis Procedure"

.

Overall Function Check

INFOID:0000000005273272

Use this procedure to check the overall function of the vehicle speed sensor circuit. During this check, a 1st
trip DTC might not be confirmed.

 WITH GST

1.

Lift up drive wheels.

2.

Start engine.

3.

Read vehicle speed sensor signal in Service $01 with GST.
The vehicle speed sensor on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.

4.

If NG, go to 

EC-271, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005273273

1.

CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”

Refer to 

BRC-21, "CONSULT-III Function (ABS)"

.

OK or NG

OK

>> GO TO 2.

NG

>> Repair or replace.

2.

CHECK COMBINATION METER

Refer to 

MWI-21

.

>> INSPECTION END

Shift lever

Except P or N position (A/T)
Except Neutral position (M/T)

PW/ST SIGNAL

OFF

EC-272

< COMPONENT DIAGNOSIS >

[QR25DE]

P0506 ISC SYSTEM

P0506 ISC SYSTEM

Description

INFOID:0000000005273274

NOTE:
If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration and engine load (air conditioner, power steering and cooling fan
operation, etc.). 

On Board Diagnosis Logic

INFOID:0000000005273275

DTC Confirmation Procedure

INFOID:0000000005273276

NOTE:
• If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at

least 10 seconds before conducting the next test.

• If the target idle speed is out of the specified value, perform 

EC-24, "Idle Air Volume Learning"

,

before conducting DTC Confirmation Procedure. For the target idle speed, refer to the 

EC-460

.

TESTING CONDITION:
• Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
• Always perform the test at a temperature above 

10

°

C (14

°

F).

 WITH CONSULT-III

1.

Open engine hood.

2.

Start engine and warm it up to normal operating temperature.

3.

Turn ignition switch OFF and wait at least 10 seconds.

4.

Start engine and run it for at least 1 minute at idle speed.

5.

Check 1st trip DTC.

6.

If 1st trip DTC is detected, go to 

EC-272, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-III” above.

Diagnosis Procedure

INFOID:0000000005273277

1.

CHECK INTAKE AIR LEAK

1.

Start engine and let it idle.

2.

Listen for an intake air leak after the mass air flow sensor.

OK or NG

OK

>> GO TO 2.

NG

>> Discover air leak location and repair.

2.

REPLACE ECM

1.

Stop engine.

2.

Replace ECM.

3.

Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to

EC-23, "Procedure After Replacing ECM"

.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0506
0506

Idle speed control system 
RPM lower than expected

The idle speed is less than the target idle 
speed by 100 rpm or more.

• Electric throttle control actuator
• Intake air leak

EC-274

< COMPONENT DIAGNOSIS >

[QR25DE]

P0507 ISC SYSTEM

P0507 ISC SYSTEM

Description

INFOID:0000000005273278

NOTE:
If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration and engine load (air conditioner, power steering and cooling fan
operation, etc.). 

On Board Diagnosis Logic

INFOID:0000000005273279

DTC Confirmation Procedure

INFOID:0000000005273280

NOTE:
• If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at

least 10 seconds before conducting the next test.

• If the target idle speed is out of the specified value, perform 

EC-24, "Idle Air Volume Learning"

,

before conducting DTC Confirmation Procedure. For the target idle speed, refer to the 

EC-460

.

TESTING CONDITION:
• Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
• Always perform the test at a temperature above 

10

°

C (14

°

F).

 WITH CONSULT-III

1.

Open engine hood.

2.

Start engine and warm it up to normal operating temperature.

3.

Turn ignition switch OFF and wait at least 10 seconds.

4.

Start engine and run it for at least 1 minute at idle speed.

5.

Check 1st trip DTC.

6.

If 1st trip DTC is detected, go to 

EC-274, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-III” above.

Diagnosis Procedure

INFOID:0000000005273281

1.

CHECK PCV HOSE CONNECTION

Confirm that PCV hose is connected correctly.

OK or NG

OK

>> GO TO 2.

NG

>> Repair or replace.

2.

CHECK INTAKE AIR LEAK

1.

Start engine and let it idle.

2.

Listen for an intake air leak after the mass air flow sensor.

OK or NG

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0507
0507

Idle speed control system 
RPM higher than expected

The idle speed is more than the target idle 
speed by 200 rpm or more.

• Electric throttle control actuator
• Intake air leak
• PCV system

 

 

 

 

 

 

 

Content   ..  393  394  395  396   ..