Nissan Frontier D40. Manual - part 1070

 

  Index      Nissan     Nissan Frontier D40 (2010 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1068  1069  1070  1071   ..

 

 

Nissan Frontier D40. Manual - part 1070

 

 

TM-178

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P0734 4GR INCORRECT RATIO

P0734 4GR INCORRECT RATIO

Description

INFOID:0000000005274053

This malfunction is detected when the A/T does not shift into 4GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or shorted) but mechanical malfunction such as control
valve sticking, improper solenoid valve operation.

On Board Diagnosis Logic

INFOID:0000000005274054

• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0734” with CONSULT-III or 21th judgment flicker without CONSULT-III is detected

when TCM detects any inconsistency in the actual gear ratio.

Possible Cause

INFOID:0000000005274055

• Input clutch solenoid valve
• Front brake solenoid valve
• Direct clutch solenoid valve
• High and low reverse clutch solenoid valve
• Each clutch
• Hydraulic control circuit

DTC Confirmation Procedure

INFOID:0000000005274056

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1.

Start the engine and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

2.

Make sure that “ATF TEMP 1” is within the following range.
ATF TEMP 1: 20

°

C – 180

°

C

If out of range, drive vehicle to warm ATF or stop engine to cool ATF.

3.

Select “4TH GR FNCTN P0734” of “DTC & SRT CONFIRMATION” mode for “TRANSMISSION” with
CONSULT-III.

4.

Drive vehicle and maintain the following conditions.
SLCT LVR POSI: “D” position
GEAR: “4” position
ACCELE POSI: 0.6/8 or more
VEHICLE SPEED: 10 km/h (6 MPH) or more
ENGINE SPEED: INPUT SPEED 

 50 rpm or more

INPUT SPEED: 300 rpm or more

5.

Keep the current driving status for at least 5 consecutive seconds if CONSULT-III screen changes from
“OUT OF CONDITION” to “TESTING”.

CAUTION:

If “TESTING” does not appear on CONSULT-III for a long time, select “SELF-DIAG RESULTS”. In
case a 1st trip DTC other than P0734 is shown, refer to “

TM-151, "CONSULT-III Function (TRANS-

MISSION)"

”.

If “COMPLETED RESULT NG” is detected, go to

TM-179, "Diagnosis Procedure"

.

If “STOP VEHICLE” is detected, go to the following step.

6.

Stop vehicle.

7.

Drive vehicle in “D” position allowing it to shift from 1GR to 5GR and check shift timing and shift shock.

-

Touch “OK” to complete the inspection when normally shifted from the 1GR to 5GR.

-

Touch “NG” when an unusual shift shock, etc. occurs in spite of shifting from the 1GR to 5GR. Go to 

TM-

271, "Check Before Engine Is Started"

.

-

Perform 

TM-151, "CONSULT-III Function (TRANSMISSION)"

 when not shifted from the 1GR to 5GR.

(Neither “OK” nor “NG” are indicated.)

 WITH GST

P0734 4GR INCORRECT RATIO

TM-179

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

Start the engine.

2.

Drive vehicle for approximately 5 minutes in urban areas.

3.

Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
Selector lever: “D” position
Gear position: “4” position
Accelerator opening: 0.6/8 or more
Vehicle speed: 10 km/h (6 MPH) or more

4.

Check DTC.

5.

If DTC is detected, go to 

TM-179, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005274057

1.

CHECK CAN COMMUNICATION LINE

Perform self-diagnosis. Refer to 

TM-151, "CONSULT-III Function (TRANSMISSION)"

TM-156, "Diagnosis

Procedure without CONSULT-III"

.

Is a malfunction in the CAN communication indicated in the results?

YES

>> Check CAN communication line. Refer to 

TM-159, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-210, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTION ITEM

Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

REPLACE CONTROL VALVE WITH TCM

1.

Replace control valve with TCM. Refer to 

TM-280, "Removal and Installation"

.

2.

Perform 

TM-178, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to 

TM-271,

"Check Before Engine Is Started"

.

TM-180

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P0735 5GR INCORRECT RATIO

P0735 5GR INCORRECT RATIO

Description

INFOID:0000000005274058

This malfunction is detected when the A/T does not shift into 5GR position as instructed by TCM. This is not
only caused by electrical malfunction (circuits open or shorted) but mechanical malfunction such as control
valve sticking, improper solenoid valve operation.

On Board Diagnosis Logic

INFOID:0000000005274059

• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0735” with CONSULT-III or 22th judgment flicker without CONSULT-III is detected

when TCM detects any inconsistency in the actual gear ratio.

Possible Cause

INFOID:0000000005274060

• Input clutch solenoid valve
• Front brake solenoid valve
• Direct clutch solenoid valve
• High and low reverse clutch solenoid valve
• Each clutch
• Hydraulic control circuit

DTC Confirmation Procedure

INFOID:0000000005274061

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1.

Start the engine and select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

2.

Make sure that “ATF TEMP 1” is within the following range.
ATF TEMP 1: 20

°

C – 180

°

C

If out of range, drive vehicle to warm ATF or stop engine to cool ATF.

3.

Select “5TH GR FNCTN P0735” of “DTC & SRT CONFIRMATION” mode for “TRANSMISSION” with
CONSULT-III.

4.

Drive vehicle and maintain the following conditions.
SLCT LVR POSI: “D” position
GEAR: “5” position
ACCELE POSI: 0.6/8 or more
VEHICLE SPEED: 10 km/h (6 MPH) or more
ENGINE SPEED: INPUT SPEED 

 50 rpm or more

INPUT SPEED: 300 rpm or more

5.

Keep the current driving status for at least 5 consecutive seconds if CONSULT-III screen changes from
“OUT OF CONDITION” to “TESTING”.

CAUTION:

If “TESTING” does not appear on CONSULT-III for a long time, select “SELF-DIAG RESULTS”. In
case a 1st trip DTC other than P0735 is shown, refer to “

TM-151, "CONSULT-III Function (TRANS-

MISSION)"

”.

If “COMPLETED RESULT NG” is detected, go to 

TM-181, "Diagnosis Procedure"

.

If “STOP VEHICLE” is detected, go to the following step.

6.

Stop vehicle.

7.

Drive vehicle in “D” position allowing it to shift from 1GR to 5GR and check shift timing and shift shock.

-

Touch “OK” to complete the inspection when normally shifted from the 1GR to 5GR.

-

Touch “NG” when an unusual shift shock, etc. occurs in spite of shifting from the 1GR to 5GR. Go to 

TM-

271, "Check Before Engine Is Started"

.

-

Perform 

TM-151, "CONSULT-III Function (TRANSMISSION)"

 when not shifted from the 1GR to 5GR.

(Neither “OK” nor “NG” are indicated.)

 WITH GST

P0735 5GR INCORRECT RATIO

TM-181

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

Start the engine.

2.

Drive vehicle for approximately 5 minutes in urban areas.

3.

Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
Selector lever: “D” position
Gear position: “5” position
Accelerator opening: 0.6/8 or more
Vehicle speed: 10 km/h (6 MPH) or more

4.

Check DTC.

5.

If DTC is detected, go to 

TM-181, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005274062

1.

CHECK CAN COMMUNICATION LINE

Perform self-diagnosis. Refer to 

TM-151, "CONSULT-III Function (TRANSMISSION)"

TM-156, "Diagnosis

Procedure without CONSULT-III"

.

Is a malfunction in the CAN communication indicated in the results?

YES

>> Check CAN communication line. Refer to 

TM-159, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-210, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTION ITEM

Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

REPLACE CONTROL VALVE WITH TCM

1.

Replace control valve with TCM. Refer to 

TM-280, "Removal and Installation"

.

2.

Perform 

TM-180, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to 

TM-271,

"Check Before Engine Is Started"

.

 

 

 

 

 

 

 

Content   ..  1068  1069  1070  1071   ..