Nissan Quest E52. Manual - part 617

EXL-72

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

PARKING LAMP CIRCUIT

PARKING LAMP CIRCUIT

Component Function Check

INFOID:0000000009653053

1.

CHECK PARKING LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the parking lamp is turned ON.

Is the inspection result normal?

YES

>> Parking lamp circuit is normal.

NO

>> Refer to 

EXL-72, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009653054

1.

CHECK PARKING LAMP FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK PARKING LAMP SHORT CIRCUIT

1.

Disconnect the following connectors.

-

IPDM E/R

-

Front combination lamp

-

Front side marker lamp

-

Headlamp aiming motor

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace fuse. (Replace IPDM E/R if fusing is found again.)

NO

>> Repair or replace harness. And then replace the fuse.

3.

CHECK PARKING LAMP BULB

Check applicable lamp bulb.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace bulb.

4.

CHECK PARKING LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

TAIL

: Parking lamp ON

Off

: Parking lamp OFF

Unit

Location

Fuse No.

Capacity

• Parking  lamp
• Front side marker lamp

IPDM E/R

#52

10 A

IPDM E/R

Ground

Continuity

Connector

Terminal

E346

91

Not existed

92

93

94

PARKING LAMP CIRCUIT

EXL-73

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

1.

Disconnect front combination lamp connector.

2.

Turn ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace IPDM E/R.

5.

CHECK PARKING LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and front combination lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK PARKING LAMP GROUND OPEN CIRCUIT

Check continuity between front combination lamp harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

(+)

(

−

)

Test  item

Voltage

(Approx.)

IPDM E/R

Connector

Terminal

RH

E346

91

Ground

EXTERNAL 
LAMPS

TAIL

Battery voltage

Off

0 V

LH

92

TAIL

Battery voltage

Off

0 V

IPDM E/R

Front combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E346

91

E349

1

Existed

LH

92

E348

Front combination lamp

Ground

Continuity

Connector

Terminal

RH

E349

2

Existed

LH

E348

EXL-74

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

FRONT SIDE MARKER LAMP CIRCUIT

FRONT SIDE MARKER LAMP CIRCUIT

Component Function Check

INFOID:0000000009653055

1.

CHECK PARKING LAMP OPERATION

Check that the parking lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check parking lamp circuit. Refer to 

EXL-72, "Component Function Check"

.

2.

CHECK FRONT SIDE MARKER LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the front side marker lamp is turned ON.

Is the inspection result normal?

YES

>> Front side marker lamp circuit is normal.

NO

>> Refer to 

EXL-74, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009653056

1.

CHECK FRONT SIDE MARKER LAMP BULB

Check applicable lamp bulb.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace bulb.

2.

CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector and front side marker lamp connector.

3.

Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK FRONT SIDE MARKER LAMP GROUND OPEN CIRCUIT

Check continuity between front side marker lamp harness connector and ground.

Is the inspection result normal?

YES

>> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO

>> Repair or replace harness.

TAIL

: Front side marker lamp ON

Off

: Front side marker lamp OFF

IPDM E/R

Front side marker lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E346

91

E321

1

Existed

LH

92

E320

Front side marker lamp

Ground

Continuity

Connector

Terminal

RH

E321

2

Existed

LH

E320

TAIL LAMP CIRCUIT

EXL-75

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000009653057

1.

CHECK TAIL LAMP OPERATION

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the tail lamp is turned ON.

Is the inspection result normal?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-75, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009653058

1.

CHECK TAIL LAMP FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK TAIL LAMP SHORT CIRCUIT

1.

Disconnect IPDM E/R connector, licence plate lamp connector and rear combination lamp connector.

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace fuse. (Replace IPDM E/R if fusing is found again.)

NO

>> Repair or replace harness. And then replace the fuse.

3.

CHECK TAIL LAMP BULB

Check applicable lamp bulb.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace bulb.

4.

CHECK TAIL LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1.

Disconnect rear combination lamp connector.

2.

Turn ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

TAIL

: Tail Lamp ON

Off

: Tail lamp OFF

Unit

Location

Fuse No.

Capacity

• Tail lamp
• license plate lamp

IPDM E/R

#53

10 A

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

7

Not existed