Nissan Quest E52. Manual - part 465

EC-70

< SYSTEM DESCRIPTION >

[VQ35DE]

DIAGNOSIS SYSTEM (ECM)

How to Erase DTC and 1st Trip DTC

NOTE:
• If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10

seconds and then turn it ON (engine stopped) again.

• If the DTC is not for A/T related items (see 

EC-96, "DTC Index"

), skip step 1.

1.

Erase DTC in TCM. Refer to 

TM-48, "DTC Index"

.

2.

Select “ENGINE” with CONSULT.

3.

Select “SELF-DIAG RESULTS”.

4.

Touch “ERASE”. (DTC in ECM will be erased.)

Freeze Frame Data and 1st Trip Freeze Frame Data

*: The items are the same as those of 1st trip freeze frame data.

DATA MONITOR MODE

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Monitored Item

For reference values of the following items, refer to 

EC-79, "Reference Value"

.

Freeze frame data item*

Description

DIAG TROUBLE CODE
[PXXXX]

• The engine control component part/control system has a trouble code that is displayed as PXXXX. (Refer 

to 

EC-96, "DTC Index"

.)

FUEL SYS-B1

• “Fuel injection system status” at the moment a malfunction is detected is displayed.
• One of the following mode is displayed.

Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop

FUEL SYS-B2

CAL/LD VALUE [%]

• The calculated load value at the moment a malfunction is detected is displayed.

COOLANT TEMP [

°

C] or 

[

°

F]

• The engine coolant temperature at the moment a malfunction is detected is displayed.

L-FUEL TRM-B1 [%]

• “Long-term fuel trim” at the moment a malfunction is detected is displayed.
• The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule 

than short-term fuel trim.

L-FUEL TRM-B2 [%]

S-FUEL TRM-B1 [%]

• “Short-term fuel trim” at the moment a malfunction is detected is displayed.
• The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel 

schedule.

S-FUEL TRM-B2 [%]

ENGINE SPEED [rpm]

• The engine speed at the moment a malfunction is detected is displayed.

VEHICL SPEED
[km/h] or [mph]

• The vehicle speed at the moment a malfunction is detected is displayed.

ABSOL TH·P/S [%]

• The throttle valve opening angle at the moment a malfunction is detected is displayed.

B/FUEL SCHDL [msec]

• The base fuel schedule at the moment a malfunction is detected is displayed.

INT/A TEMP SE [

°

C] or 

[

°

F]

• The intake air temperature at the moment a malfunction is detected is displayed.

INT MANI PRES [kPa] 

• These items are displayed but are not applicable to this model.

COMBUST CONDITION

DIAGNOSIS SYSTEM (ECM)

EC-71

< SYSTEM DESCRIPTION >

[VQ35DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Monitored item

Unit

Description

Remarks

ENG SPEED

rpm

• Indicates the engine speed computed from the 

signal of the crankshaft position sensor (POS) 
and camshaft position sensor (PHASE).

• Accuracy becomes poor if engine 

speed drops below the idle rpm.

• If the signal is interrupted while the 

engine is running, an abnormal value 
may be indicated.

MAS A/F SE-B1

V

• The signal voltage of the mass air flow sensor is 

displayed.

• When the engine is stopped, a certain 

value is indicated.

• When engine is running, specification 

range is indicated in “SPEC”.

B/FUEL SCHDL

msec

• “Base fuel schedule” indicates the fuel injection 

pulse width programmed into ECM, prior to any 
learned on board correction.

• When engine is running, specification 

range is indicated in “SPEC”.

A/F ALPHA-B1

%

• The mean value of the air-fuel ratio feedback cor-

rection factor per cycle is indicated.

• When the engine is stopped, a certain 

value is indicated.

• This data also includes the data for 

the air-fuel ratio learning control.

• When engine is running, specification 

range is indicated in “SPEC”.

A/F ALPHA-B2

COOLAN TEMP/S

°

C or 

°

F

• The engine coolant temperature (determined by 

the signal voltage of the engine coolant tempera-
ture sensor) is displayed.

• When the engine coolant temperature 

sensor is open or short-circuited, 
ECM enters fail-safe mode. The en-
gine coolant temperature determined 
by the ECM is displayed.

A/F SEN1 (B1)

V

• The A/F signal computed from the input signal of 

the air fuel ratio (A/F) sensor 1 is displayed.

A/F SEN1 (B2)

HO2S2 (B1)

V

• The signal voltage of the heated oxygen sensor 2 

is displayed.

HO2S2 (B2)

HO2S2 MNTR(B1)

RICH/LEAN

• Display of heated oxygen sensor 2 signal:

RICH: means the amount of oxygen after three 
way catalyst is relatively small.
LEAN: means the amount of oxygen after three 
way catalyst is relatively large.

• When the engine is stopped, a certain 

value is indicated.

HO2S2 MNTR(B2)

VHCL SPEED SE

km/h or mph

• The vehicle speed computed from the vehicle 

speed signal sent from combination meter is dis-
played.

BATTERY VOLT

V

• The power supply voltage of ECM is displayed.

ACCEL SEN 1

V

• The accelerator pedal position sensor signal volt-

age is displayed.

• ACCEL SEN 2 signal is converted by 

ECM internally. Thus, it differs from 
ECM terminal voltage signal.

ACCEL SEN 2

TP SEN 1-B1

V

• The throttle position sensor signal voltage is dis-

played.

• TP SEN 2-B1 signal is converted by 

ECM internally. Thus, it differs from 
ECM terminal voltage signal.

TP SEN 2-B1

FUEL T/TMP SE

°

C or 

°

F

• The fuel temperature (determined by the signal 

voltage of the fuel tank temperature sensor) is 
displayed.

INT/A TEMP SE

°

C or 

°

F

• The intake air temperature (determined by the 

signal voltage of the intake air temperature sen-
sor) is indicated.

EVAP SYS PRES

V

• The signal voltage of EVAP control system pres-

sure sensor is displayed.

FUEL LEVEL SE

V

• The signal voltage of the fuel level sensor is dis-

played.

START SIGNAL

ON/OFF

• Indicates start signal status [ON/OFF] computed 

by the ECM according to the signals of engine 
speed and battery voltage.

• After starting the engine, [OFF] is dis-

played regardless of the starter sig-
nal.

EC-72

< SYSTEM DESCRIPTION >

[VQ35DE]

DIAGNOSIS SYSTEM (ECM)

CLSD THL POS

ON/OFF

• Indicates idle position [ON/OFF] computed by 

ECM according to the accelerator pedal position 
sensor signal.

AIR COND SIG

ON/OFF

• Indicates [ON/OFF] condition of the air condition-

er switch as determined by the air conditioner sig-
nal.

P/N POSI SW

ON/OFF

• Indicates [ON/OFF] condition from the park/neu-

tral position (PNP) signal.

PW/ST SIGNAL

ON/OFF

• [ON/OFF] condition of the power steering system 

(determined by the signal voltage of the power 
steering pressure sensor) is indicated.

LOAD SIGNAL

ON/OFF

• Indicates [ON/OFF] condition from the electrical 

load signal.
ON: Rear window defogger switch is ON and/or 
lighting switch is in 2nd position.
OFF: Both rear window defogger switch and light-
ing switch are OFF.

IGNITION SW

ON/OFF

• Indicates [ON/OFF] condition from ignition switch 

signal.

HEATER FAN SW

ON/OFF

• Indicates [ON/OFF] condition from the heater fan 

switch signal.

BRAKE SW

ON/OFF

• Indicates [ON/OFF] condition from the stop lamp 

switch signal.

INJ PULSE-B1

msec

• Indicates the actual fuel injection pulse width 

compensated by ECM according to the input sig-
nals.

• When the engine is stopped, a certain 

computed value is indicated.

INJ PULSE-B2

IGN TIMING

BTDC

• Indicates the ignition timing computed by ECM 

according to the input signals.

• When the engine is stopped, a certain 

value is indicated.

CAL/LD VALUE

%

• “Calculated load value” indicates the value of the 

current air flow divided by peak air flow.

MASS AIRFLOW

g/s

• Indicates the mass air flow computed by ECM ac-

cording to the signal voltage of the mass air flow 
sensor.

PURG VOL C/V

%

• Indicates the EVAP canister purge volume con-

trol solenoid valve control value computed by the 
ECM according to the input signals.

• The opening becomes larger as the value in-

creases.

INT/V TIM (B1)

°

CA

• Indicates [

°

CA] of intake camshaft advance an-

gle. 

INT/V TIM (B2)

INT/V SOL-B1

%

• The control value of the intake valve timing con-

trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.

• The advance angle becomes larger as the value 

increases.

INT/V SOL-B2

VIAS S/V-1

ON/OFF

• The control condition of the VIAS control solenoid 

valve 1 (determined by ECM according to the in-
put signals) is indicated.
ON: VIAS control solenoid valve 1 is operating.
OFF: VIAS control solenoid valve 1 is not operat-
ing.

VIAS S/V-2

ON/OFF

• The control condition of the VIAS control solenoid 

valve 2 (determined by ECM according to the in-
put signals) is indicated.
ON: VIAS control solenoid valve 2 is operating.
OFF: VIAS control solenoid valve 2 is not operat-
ing.

Monitored item

Unit

Description

Remarks

DIAGNOSIS SYSTEM (ECM)

EC-73

< SYSTEM DESCRIPTION >

[VQ35DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

AIR COND RLY

ON/OFF

• The air conditioner relay control condition (deter-

mined by ECM according to the input signals) is 
indicated.

ENGINE MOUNT

IDLE/TRVL

• The control condition of the electronic controlled 

engine mount (determined by ECM according to 
the input signals) is indicated.
IDLE: Engine speed is below 950 rpm
TRVL: Engine speed is above 950 rpm

VENT CONT/V

ON/OFF

• The control condition of the EVAP canister vent 

control valve (determined by ECM according to 
the input signals) is indicated.
ON: Closed
OFF: Open

THRTL RELAY

ON/OFF

• Indicates the throttle control motor relay control 

condition determined by the ECM according to 
the input signals.

COOLING FAN

HI/MID/LOW/

OFF

• The control condition of the cooling fan (deter-

mined by ECM according to the input signals) is 
indicated.
HI: High speed operation
MID: Middle speed operation
LOW: Low speed operation
OFF: Stop

HO2S2 HTR (B1)

ON/OFF

• Indicates [ON/OFF] condition of heated oxygen 

sensor 2 heater determined by ECM according to 
the input signals.

HO2S2 HTR (B2)

I/P PULLY SPD

rpm

• Indicates the engine speed computed from the in-

put speed sensor signal.

VEHICLE SPEED

km/h or mph

• The vehicle speed computed from the vehicle 

speed signal sent from TCM is displayed.

IDL A/V LEARN

YET/CMPLT

• Displays the condition of idle air volume learning

YET: Idle Air Volume Learning has not been per-
formed yet.
CMPLT: Idle Air Volume Learning has already 
been performed successfully.

ENG OIL TEMP

°

C or 

°

F

• The engine oil temperature (determined by the 

signal voltage of the engine oil temperature sen-
sor) is displayed.

TRVL AFTER MIL

km or mile

• Distance traveled while MIL is activated.

A/F S1 HTR(B1)

%

• Air fuel ratio (A/F) sensor 1 heater control value 

computed by ECM according to the input signals.

• The current flow to the heater becomes larger as 

the value increases.

A/F S1 HTR(B2)

AC PRESS SEN

V

• The signal voltage from the refrigerant pressure 

sensor is displayed.

VHCL SPEED SE

km/h or mph

• The vehicle speed computed from the vehicle 

speed signal sent from combination meter is dis-
played.

SET VHCL SPD

km/h or mph

• The preset vehicle speed is displayed.

MAIN SW

ON/OFF

• Indicates [ON/OFF] condition from MAIN switch 

signal.

CANCEL SW

ON/OFF

• Indicates [ON/OFF] condition from CANCEL 

switch signal.

RESUME/ACC SW

ON/OFF

• Indicates [ON/OFF] condition from RESUME/AC-

CELERATE switch signal.

SET SW

ON/OFF

• Indicates [ON/OFF] condition from SET/COAST 

switch signal.

Monitored item

Unit

Description

Remarks