Nissan Quest E52. Manual - part 374

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  372  373  374  375   ..

 

 

Nissan Quest E52. Manual - part 374

 

 

DLK-210

< DTC/CIRCUIT DIAGNOSIS >

B2416 TOUCH SENSOR RH

B2416 TOUCH SENSOR RH

DTC Logic

INFOID:0000000009649107

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check “Self Diagnostic Result” mode of “AUTO BACK DOOR” using CONSULT.

Is DTC detected?

YES

>> Refer to 

DLK-210, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009649108

1.

CHECK TOUCH SENSOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Check voltage between back door touch sensor RH harness connector and automatic back door control
module harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BACK DOOR TOUCH SENSOR RH CIRCUIT

1.

Disconnect automatic back door control module connector and back door touch sensor RH connector.

2.

Check continuity between automatic back door control module harness connector and back door touch
sensor RH harness connector.

3.

Check continuity between automatic back door control module harness connector and ground.

DTC

CONSULT display 

description

DTC detecting condition

Possible cause

B2416

TOUCH SEN R 
OPEN

 When the automatic back door control unit detects 
the open circuit of the back door touch sensor  RH

• Back door touch sensor  RH
• Harness or connectors

(Back door touch sensor  RH cir-
cuit is open)

• Automatic back door control mod-

ule

(+)

(–)

Condition

Voltage

Back door touch sensor RH

Automatic back door control mod-

ule

 Connector

Terminal

 Connector

Terminal

D191

1

B8

14

Back door touch 
sensor RH

Detect obstruc-
tion

0 – 1.5 V

Other than 
above

5 – 6.7 V

Automatic back door control module

Back door touch sensor RH

Continuity 

 Connector

Terminal

Connector

Terminal

B8

13

D191

1

Existed

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B8

13

Not existed

B2416 TOUCH SENSOR RH

DLK-211

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-495, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK BACK DOOR TOUCH SENSOR RH GROUND CIRCUIT

1.

Disconnect automatic back door control module connector and back door touch sensor RH connector.

2.

Check continuity between automatic back door control module harness connector and back door touch
sensor RH harness connector.

3.

Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK BACK DOOR TOUCH SENSOR RH GROUND CIRCUIT 2

1.

Connect automatic back door control module connector and back door touch sensor RH connector.

2.

Check voltage between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace automatic back door control module. Refer to 

DLK-495, "Removal and Installation"

.

5.

CHECK BACK DOOR TOUCH SENSOR RH

Refer to 

DLK-211, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace back door touch sensor RH.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000009649109

1.

CHECK TOUCH SENSOR RH

1.

Turn ignition switch OFF.

2.

Disconnect back door touch sensor RH connector.

3.

Check resistance between back door touch sensor RH terminals.

Automatic back door control module

Back door touch sensor RH

Continuity 

 Connector

Terminal

Connector

Terminal

B8

14

D191

2

Existed

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B8

14

Not existed

(+)

(–)

Voltage

Automatic back door control module

 Connector

Terminal

B8

14

Ground

0 – 1.5 V

DLK-212

< DTC/CIRCUIT DIAGNOSIS >

B2416 TOUCH SENSOR RH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace back door touch sensor RH.

Back door touch sensor RH

 Condition

Resistance 

Terminal

1

2

Back door touch sensor  
RH

Detect obstruction

360 - 440 

Ω

Other than above

0.9 - 1.1 k

Ω

B2417 TOUCH SENSOR LH

DLK-213

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

B2417 TOUCH SENSOR LH

DTC Logic

INFOID:0000000009649110

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check “Self Diagnostic Result” mode of “AUTO BACK DOOR” using CONSULT.

Is DTC detected?

YES

>> Refer to 

DLK-213, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009649111

1.

CHECK BACK DOOR TOUCH SENSOR  INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Check voltage between back door touch sensor  LH harness connector and automatic back door control
module harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BACK DOOR TOUCH SENSOR  LH CIRCUIT

1.

Disconnect automatic back door control module connector and back door touch sensor  LH connector.

2.

Check continuity between automatic back door control module harness connector and back door touch
sensor  LH harness connector.

3.

Check continuity between automatic back door control module harness connector and ground.

DTC

CONSULT display 

description

DTC detecting condition

Possible cause

B2417

TOUCH SEN L 
OPEN

When the automatic back door control unit detects 
the open circuit of the back door touch sensor  LH.

• Back door touch sensor  LH
• Harness or connectors

(Back door touch sensor  LH circuit 
is open)

• Automatic back door control mod-

ule

(+)

(–)

Condition

Voltage

Back door touch sensor  LH

Automatic back door control mod-

ule

 Connector

Terminal

 Connector

Terminal

D165

1

B8

14

Back door touch 
sensor  LH

Detect obstruc-
tion

0 – 1.5 V

Other than 
above

5 – 6.7 V

Automatic back door control module

Back door touch sensor  LH

Continuity 

 Connector

Terminal

Connector

Terminal

B8

15

D165

1

Existed

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B8

15

Not existed

 

 

 

 

 

 

 

Content   ..  372  373  374  375   ..