Nissan Quest E52. Manual - part 1261

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

5.

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK TIRE PRESSURE RECEIVER IGNITION SUPPLY CIRCUIT

1.

Connect tire pressure receiver harness connector.

2.

Install 10A fuse (#10).

CAUTION:

Check that the fuse is not blown, that there are no other abnormalities, and that the fuse is of the
specified capacity.

3.

Check the voltage between tire pressure receiver harness connector and the ground when the ignition
switch is turned ON and OFF.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK TIRE PRESSURE SIGNAL

Check the function tire pressure receiver. Refer to 

DLK-265, "Component Function Check"

.

Is the inspection result normal?

YES

>> Replace the BCM.

NO

>> Repair or replace error-detected parts.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M121

18

R108

4

Existed

38

2

M123

57

1

BCM

—

Continuity

Connector

Terminal

M121

18

Ground

Not existed

38

M123

57

Tire pressure receiver

—

Voltage

Connector

Terminal

R108

1

Ground

9 – 16 V

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000009653435

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION 

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-51, "Tire Air Pres-

sure"

. 

CAUTION:

If the tire pressure before adjustment is close to the standard, reduce the tire pressure, and then
with the ignition switch ON, adjust the tire pressure again so that it is within the standard.

3.

Perform self-diagnosis in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1716”, “C1717”, “C1718”, or “C1719” detected?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

CHECK LOW TIRE PRESSURE WARNING LAMP

Check that after the ignition switch is turned ON, the low tire pressure warning lamp illuminates for approxi-
mately 1 second and then turns OFF.

Is the inspection result normal?

YES

>> After erase DTC, INSPECTION END.

NO

>> Leave the ignition switch ON and proceed to 

WT-29, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009653436

1.

PERFORM TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration for all wheels. Refer to 

WT-23, "Work Procedure"

. 

Is tire pressure sensor ID registration completed?

YES

>> GO TO 2.

NO

>> Replace tire pressure sensor. Refer to 

WT-48, "Removal and Installation"

.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

1.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-51, "Tire Air Pres-

sure"

.

2.

Stop the vehicle.

3.

Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

4.

Within 15 minutes after vehicle stopped, read the values that are displayed for “AIR PRESS FL”, “AIR
PRESS FR”, “AIR PRESS RR”, and “AIR PRESS RL”.

Which tire pressures is displayed as 438.60 kPa (4.47 kg/cm

2

, 63.60 psi)?

DTC

Display Item

Malfunction detected condition

Possible causes

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the 
front LH wheel tire pressure sensor.

• Excessive tire pressure
• Tire pressure sensor ID reg-

istration incomplete

• Tire pressure sensor

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the 
front RH wheel tire pressure sensor.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the 
rear RH wheel tire pressure sensor.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the 
rear LH wheel tire pressure sensor.

WT-30

< DTC/CIRCUIT DIAGNOSIS >

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

YES

>> Replace tire pressure sensor the tire pressure as 438.60 kPa (4.47 kg/cm

2

, 63.60 psi) displayed.

Refer to 

WT-48, "Removal and Installation"

.

NO

>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to 

BCS-63,

"DTC Index"

.

C1729 VEHICLE SPEED SIGNAL

WT-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1729 VEHICLE SPEED SIGNAL

DTC Logic

INFOID:0000000009653437

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Drive the vehicle.

2.

Stop the vehicle.

3.

Perform self-diagnosis in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Proceed to 

WT-31, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009653438

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is any DTCs detected?

YES

>> Check the DTCs.

NO

>> GO TO 2.

2.

CHECK BCM INPUT/OUTPUT SIGNAL

Check BCM input/output signal values. Refer to 

BCS-40, "Reference Value"

. 

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions. 

NO

>> Replace the BCM. Refer to 

BCS-98, "Removal and Installation"

.

DTC

Display Item

Malfunction detected condition

Possible causes

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

With intelligent key

• CAN communication
• BCM
• ABS actuator and elec-

tric unit (control unit) 
malfunction