Nissan Quest E52. Manual - part 1107

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1105  1106  1107  1108   ..

 

 

Nissan Quest E52. Manual - part 1107

 

 

SEC-118

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-36, "Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(–)

Continuity

IPDM E/R

Connector

Terminal

F12

72

Ground

Not existed

HEADLAMP FUNCTION

SEC-119

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

HEADLAMP FUNCTION

Component Function Check

INFOID:0000000009650787

1.

CHECK FUNCTION

1.

Perform “HEAD LAMP(HI)” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CONSULT.

2.

Check headlamps operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

SEC-119, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009650788

1.

CHECK HEADLAMP FUNCTION

Refer to 

EXL-62, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check"

 (Xenon

type without daytime running light system),

EXL-63, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check"

 (Xenon type with day-

time running light system),

EXL-174, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check"

 (Halogen type

without daytime running light system), or

EXL-175, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check"

 (Halogen type with

daytime running light system).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Test item

Description

HEAD LAMP (HI)

ON

Headlamps (Hi)

Light

OFF

Do not light

SEC-120

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

HORN FUNCTION

HORN FUNCTION

Component Function Check

INFOID:0000000009650789

1.

CHECK FUNCTION

1.

Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT.

2.

Check the horn operation.

Is the operation normal?

YES

>> INSPECTION END

NO

>> Go to 

SEC-120, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009650790

1.

CHECK HORN FUNCTION

Check that horn functions properly using horn switch.

Do horns sound?

YES

>> GO TO 2.

NO

>> Check horn circuit. Refer to 

HRN-3, "Wiring Diagram"

.

2.

CHECK HORN CONTROL CIRCUIT

1.

Disconnect horn relay.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and horn relay harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Test item

Description

VEHICLE SECURITY HORN

ON

Horn

Sounds (for 0.5 sec)

IPDM E/R

Horn relay

Continuity

Connector

Terminal

Connector

Terminal

E11

44

E5

1

Existed

SECURITY INDICATOR LAMP

SEC-121

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SECURITY INDICATOR LAMP

Component Function Check

INFOID:0000000009650791

1.

CHECK FUNCTION

1.

Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT.

2.

Check security indicator lamp operation.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

SEC-121, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009650792

1.

CHECK FUSE

1.

Turn power switch OFF.

2.

Check that the following fuse in the fuse block (J/B) is not blown.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the blown fuse after repairing the cause of blowing.

2.

CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT

1.

Disconnect combination meter connector.

2.

Check voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK SECURITY INDICATOR LAMP SIGNAL

1.

Connect combination meter connector.

2.

Disconnect BCM connector.

3.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 5.

4.

REPLACE BCM

Test item

Description

THEFT IND

ON

Security indicator lamp

Illuminates

OFF

Does not illuminate

Signal name

Fuse No.

Battery power supply

11 (10 A)

(+)

(–)

Voltage (V)

(Approx.)

Combination meter

Connector

Terminal

M34

1

Ground

Battery voltage

(+)

(–)

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M121

23

Ground

Battery voltage

 

 

 

 

 

 

 

Content   ..  1105  1106  1107  1108   ..