Nissan Quest E52. Manual - part 23

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  21  22  23  24   ..

 

 

Nissan Quest E52. Manual - part 23

 

 

MIRROR SENSOR

ADP-85

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

NO

>> Refer to 

ADP-85, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000009649677

1.

CHECK DOOR MIRROR SENSOR (PASSENGER SIDE) POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (passenger side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR POWER SUPPLY CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to 

ADP-112, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

3.

CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness or connector.

(+)

(-)

Voltage (V)

Door mirror (passenger side)

Connector

Terminals

D3

23

Ground

4 – 6

Automatic drive positioner control unit

Door mirror (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M75

21

D3

23

Existed

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M75

21

Not existed

Automatic drive positioner control unit

Door mirror (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M75

20

D3

24

Existed

Automatic drive positioner control unit

Ground

Continuity

Connector

Terminal

M75

20

Not existed

ADP-86

< DTC/CIRCUIT DIAGNOSIS >

MIRROR SENSOR

4.

CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR CIRCUIT

1.

Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.

2.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace door mirror sensor (built in passenger side door mirror).

NO

>> Repair or replace harness or connector.

Automatic drive positioner control unit

Door mirror (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M75

5

D3

21

Existed

17

22

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M75

5

Not existed

17

SLIDING MOTOR

ADP-87

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SLIDING MOTOR

Component Function Check

INFOID:0000000009649678

1.

CHECK FUNCTION

1.

Select “SEAT SLIDE” in “Active test” mode with CONSULT.

2.

Check the sliding motor operation.

Is the operation of relevant parts normal?

YES

>> INSPECTION END

NO

>> Refer to 

ADP-87, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009649679

1.

CHECK SLIDING MOTOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding motor connector.

3.

Turn ignition switch ON.

4.

Perform “Active test” (“SEAT SLIDE”) with CONSULT.

5.

Check voltage between sliding motor harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding motor (built in seat slide cushion frame).

NO

>> GO TO 2.

2.

CHECK SLIDING MOTOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect driver seat control unit connector.

3.

Check continuity between driver seat control unit harness connector and sliding motor harness connector.

4.

Check continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

Test item

Description

SEAT SLIDE

OFF

Seat sliding

Stop

FR

Forward

RR

Backward

(+)

(-)

Condition

Voltage (V)

Sliding motor

Connector

Terminals

B561

34

Ground

SEAT SLIDE

OFF

0 – 1

Backward

9 – 16

38

OFF

0 – 1

Forward

9 – 16

Driver seat control unit

Sliding motor

Continuity

Connector

Terminal

Connector

Terminal

B551

34

B561

34

Existed

38

38

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B551

34

Not existed

38

ADP-88

< DTC/CIRCUIT DIAGNOSIS >

SLIDING MOTOR

YES

>> Replace driver seat control unit. Refer to 

ADP-111, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

 

 

 

 

 

 

 

Content   ..  21  22  23  24   ..