Nissan Cube. Manual - part 899

 

  Index      Nissan     Nissan Cube (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  897  898  899  900   ..

 

 

Nissan Cube. Manual - part 899

 

 

B1130 SIDE AIR BAG MODULE RH

SRC-113

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-12, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-112, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-114

< DTC/CIRCUIT DIAGNOSIS >

B1131 SIDE AIR BAG MODULE RH

B1131 SIDE AIR BAG MODULE RH

Description

INFOID:0000000009946229

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946230

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-114, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946231

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-114, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1131

SIDE MODULE RH 
[GND-SHORT]

Side air bag module RH circuit is shorted 
to ground

• Disconnection of wiring harness and short
• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit

B1131 SIDE AIR BAG MODULE RH

SRC-115

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

4.

REPLACE SIDE AIR BAG MODULE

1.

Replace side air bag module RH. Refer to 

SE-12, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-114, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-116

< DTC/CIRCUIT DIAGNOSIS >

B1132 SIDE AIR BAG MODULE RH

B1132 SIDE AIR BAG MODULE RH

Description

INFOID:0000000009946232

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000009946233

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-116, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946234

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-116, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1132

SIDE MODULE RH 
[SHORT]

Side air bag module RH circuits are short-
ed to each other

• Disconnection of wiring harness and short
• Malfunction in side air bag module RH
• Malfunction in air bag diagnosis sensor unit

 

 

 

 

 

 

 

Content   ..  897  898  899  900   ..