Nissan Cube. Manual - part 882

B1033, B1034 CRASH ZONE SENSOR

SRC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-44, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-46

< DTC/CIRCUIT DIAGNOSIS >

B1035 CRASH ZONE SENSOR

B1035 CRASH ZONE SENSOR

Description

INFOID:0000000009946127

Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal
collision that is more than the specified limit is detected. 

DTC Logic

INFOID:0000000009946128

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-46, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946129

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-22, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-46, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1035

CRASH ZONE SEN-
SOR 
[COMM FAIL]

Crash zone sensor is malfunctioning 

• Disconnection of wiring harness
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit

B1035 CRASH ZONE SENSOR

SRC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-46, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-48

< DTC/CIRCUIT DIAGNOSIS >

B1036 CRASH ZONE SENSOR

B1036 CRASH ZONE SENSOR

Description

INFOID:0000000009946130

Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal
collision that is more than the specified limit is detected. 

DTC Logic

INFOID:0000000009946131

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-48, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946132

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE CRASH ZONE SENSOR

1.

Replace crash zone sensor. Refer to 

SR-22, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-48, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1036

CRASH ZONE SEN-
SOR 
[UNMATCH]

Crash zone sensor is out of the speci-
fied specification 

Diagnosis sensor unit or crash zone sensor is differ-
ent from the part specified