Nissan Cube. Manual - part 877

DIAGNOSIS SYSTEM (OCCUPANT DETECTION SYSTEM)

SRC-25

< SYSTEM DESCRIPTION >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSIS SYSTEM (OCCUPANT DETECTION SYSTEM)

CONSULT Function

INFOID:0000000009946096

ZERO POINT RESET DESCRIPTION

This vehicle adopts occupant detection system with a weight detecting method. When replacing, or removing
and installing passenger seat, always perform “zero point rest” so that the vehicle recognizes zero point.
If zero point reset is incomplete, occupant detection sensor does not operate normally.

WORK SUPPORT

Monitor item

Description

Zero point reset function

Perform zero point reset. Refer to 

SRC-9, "ZERO POINT RE-

SET : Special Repair Requirement"

.

SRC-26

< DTC/CIRCUIT DIAGNOSIS >

B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT

DTC/CIRCUIT DIAGNOSIS

B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000009946097

• It detects a shock that is more than the specified level and monitors whether the driver and passenger air

bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. 

• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-

tery damage in collision.

DTC Logic

INFOID:0000000009946098

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-26, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946099

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

.

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1001
B1002
B1003
B1004
B1005

CONTROL UNIT

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT

SRC-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2.

Perform DTC confirmation procedure. Refer to 

SRC-26, "DTC Logic"

.

Is DTC detected?

YES

>>  GO TO 1.

NO

>> INSPECTION END

SRC-28

< DTC/CIRCUIT DIAGNOSIS >

B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT

B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000009946100

• It detects a shock that is more than the specified level and monitors whether the driver and passenger air

bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. 

• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-

tery damage in collision.

DTC Logic

INFOID:0000000009946101

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self-Diagnostic Result.

 Without CONSULT

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-18, "Diagnosis with Air Bag Warning Lamp"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-28, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009946102

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Exploded View"

2.

Perform DTC confirmation procedure. Refer to 

SRC-28, "DTC Logic"

Is DTC detected?

DTC

Display contents of 

CONSULT

DTC detecting condition

Possible cause

B1006
B1007
B1008
B1009
B1010

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit