Nissan Cube. Manual - part 443

EXL-46

< DTC/CIRCUIT DIAGNOSIS >

FRONT FOG LAMP CIRCUIT

FRONT FOG LAMP CIRCUIT

Component Function Check

INFOID:0000000009945145

1.

CHECK FRONT FOG LAMP OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Start IPDM E/R auto active test. Refer to 

PCS-10, "Diagnosis Description"

.

2.

Check that the front fog lamp is turned ON.

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the front fog lamp is turned ON.

Is the front fog lamp turned ON?

YES

>> Front fog lamp circuit is normal.

NO

>> Refer to 

EXL-46, "Diagnosis Procedure"

. 

Diagnosis Procedure

INFOID:0000000009945146

1.

CHECK FRONT FOG LAMP FUSE

1.

Turn the ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the fuse fusing?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK FRONT FOG LAMP SHORT CIRCUIT

1.

Disconnect IPDM E/R connector and the front fog connector.

2.

Check continuity between the IPDM E/R harness connector and the ground.

Does continuity exist?

YES

>> Repair the harnesses or connectors. And then replace the fuse.

NO

>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)

3.

CHECK FRONT FOG LAMP BULB

Check the applicable lamp bulb.
Is the bulb normal?

YES

>> GO TO 4.

NO

>> Replace the bulb.

4.

CHECK FRONT FOG LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

1.

Disconnect the front fog lamp connector.

2.

Turn the ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

Fog

: Front fog lamp ON

Off

: Front fog lamp OFF

Unit

Location

Fuse No.

Capacity

Front fog lamp

IPDM E/R

#50

15 A

IPDM E/R

Ground

Continuity

Connector

Terminal

RH

E12

21

Not existed

LH

22

FRONT FOG LAMP CIRCUIT

EXL-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

4.

With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.

Is the measurement value normal?

YES

>> GO TO 5.

NO

>> Replace IPDM E/R.

5.

CHECK FRONT FOG LAMP OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between the IPDM E/R harness connector and the front fog lamp harness connector.

Does continuity exist?

YES

>> GO TO 6.

NO

>> Repair the harnesses or connectors.

6.

CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT

Check continuity between the front fog lamp harness connector and the ground.

Does continuity exist?

YES

>> Replace the front fog lamp.

NO

>> Repair the harnesses or connectors.

Terminals

Test item

Voltage

(Approx.)

(+)

(

−

)

IPDM E/R

Ground

EXTERNAL 

LAMPS

Connector

Terminal

RH

E12

21

Fog

Battery 
voltage

Off

0 V

LH

22

Fog

Battery 
voltage

Off

0 V

IPDM E/R

Front fog lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E12

21

E48

1

Existed

LH

22

E30

1

Front fog lamp

Ground

Continuity

Connector

Terminal

RH

E48

2

Existed

LH

E30

2

EXL-48

< DTC/CIRCUIT DIAGNOSIS >

PARKING LAMP CIRCUIT

PARKING LAMP CIRCUIT

Component Function Check

INFOID:0000000009945151

1.

CHECK PARKING LAMP OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Start IPDM E/R auto active test. Refer to 

PCS-10, "Diagnosis Description"

 (with Intelligent Key) or 

PCS-

41, "Diagnosis Description"

 (without Intelligent Key).

2.

Check that the parking lamp is turned ON.

CONSULT ACTIVE TEST

1.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2.

With operating the test items, check that the parking lamp is turned ON.

Is the parking lamp turned ON?

YES

>> Parking lamp circuit is normal.

NO

>> Refer to 

EXL-48, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009945152

1.

CHECK PARKING LAMP FUSE

1.

Turn the ignition switch OFF.

2.

Check that the following fuses are not fusing.

Is the fuse fusing?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK PARKING LAMP SHORT CIRCUIT

1.

Disconnect IPDM E/R connector and the parking lamp connector.

2.

Check continuity between the IPDM E/R harness connector and the ground.

Does continuity exist?

YES

>> Repair the harnesses or connectors. And then replace the fuse.

NO

>> Replace the fuse. (Replace IPDM E/R if fusing is found again.)

3.

CHECK PARKING LAMP BULB

Check the applicable lamp bulb.

Is the bulb normal?

YES

>> GO TO 4.

NO

>> Replace the bulb.

4.

CHECK PARKING LAMP OUTPUT VOLTAGE

CONSULT ACTIVE TEST

TAIL

: Parking lamp ON

Off

: Parking lamp OFF

Unit

Location

Fuse No.

Capacity

• Parking  lamp
• License plate lamp
• Side marker lamp
• Tail  lamp

IPDM E/R

#47

10 A

IPDM E/R

Ground

Continuity

Connector

Terminal

RH

E14

37

Not existed

LH

36

PARKING LAMP CIRCUIT

EXL-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

1.

Disconnect the parking lamp connector.

2.

Turn the ignition switch ON.

3.

Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4.

With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.

Is the measurement value normal?

YES

>> GO TO 5.

NO

>> Replace IPDM E/R.

5.

CHECK PARKING LAMP OPEN CIRCUIT

1.

Turn the ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between the IPDM E/R harness connector and the parking lamp harness connector.

Does continuity exist?

YES

>> GO TO 6.

NO

>> Repair the harnesses or connectors.

6.

CHECK PARKING LAMP GROUND OPEN CIRCUIT

Check continuity between the parking lamp harness connector and the ground.

Does continuity exist?

YES

>> Replace the front combination lamp.

NO

>> Repair the harnesses or connectors.

Terminals

Test item

Voltage

(Approx.)

(+)

(

−

)

IPDM E/R

Ground

EXTERNAL 

LAMPS

Connector

Terminal

RH

E14

37

TAIL

Battery 
voltage

LH

36

OFF

0 V

IPDM E/R

Parking lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

37

E43

1

Existed

LH

36

E24

1

Parking lamp

Ground

Continuity

Connector

Terminal

RH

E43

2

Existed

LH

E24

2