Nissan Versa Note. Manual - part 857

WCS-42

< SYMPTOM DIAGNOSIS >

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR 

DOES NOT SOUND

SYMPTOM DIAGNOSIS

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND

Description

INFOID:0000000009654152

• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is

released.

• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking

brake applied.

Diagnosis Procedure

INFOID:0000000009654153

1.

CHECK PARKING BRAKE WARNING LAMP

1. Start the engine.

2. Check the operation of the brake warning lamp by operating the parking brake.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-54, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK PARKING BRAKE SWITCH

Check the parking brake switch. Refer to 

WCS-39, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace parking brake switch. Refer to 

PB-9, "Removal and Installation"

.

3.

CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT

Check the parking brake switch signal circuit. Refer to 

WCS-38, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-54, "Removal and Installation"

.

NO

>> Repair harness or connector.

Combination meter

Condition

Status

Brake warning lamp

When parking brake is applied

ON

When parking brake is released

OFF

WCS

THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES 

NOT SOUND

WCS-43

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND

Description

INFOID:0000000009654154

• Seat belt reminder warning does not sound.

• Seat belt reminder warning sounds continuously.

Diagnosis Procedure

INFOID:0000000009654155

1.

CHECK SEAT BELT WARNING LAMP

1. Turn ignition switch ON.

2. Check operation of seat belt warning lamp in combination meter.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-54, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK SEAT BELT BUCKLE SWITCH LH SIGNAL CIRCUIT 

Check the seat belt buckle switch LH signal circuit. Refer to 

WCS-36, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK SEAT BELT BUCKLE SWITCH LH

Check seat belt buckle switch LH. Refer to 

WCS-37, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-54, "Removal and Installation"

.

NO

>> Replace seat belt buckle switch LH. Refer to 

SR-33, "Removal and Installation"

.

Combination meter

Condition

Status

Seat belt warning lamp

When seat belt LH (driver seat) is fastened

OFF

When seat belt LH (driver seat) is unfastened

ON

WCS-44

< SYMPTOM DIAGNOSIS >

THE LIGHT REMINDER WARNING DOES NOT SOUND

THE LIGHT REMINDER WARNING DOES NOT SOUND

Description

INFOID:0000000009654156

Light reminder warning chime does not sound even though headlamps are illuminated.

Diagnosis Procedure

INFOID:0000000009654157

1.

CHECK COMBINATION METER INPUT SIGNAL

Select the Data Monitor for the METER/M&A and check the BUZZER monitor value.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-54, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT

Check the driver side door switch signal circuit. Refer to 

DLK-95, "Diagnosis Procedure"

 (with Intelligent Key)

or 

DLK-225, "Diagnosis Procedure"

 (without Intelligent Key).

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK DRIVER SIDE DOOR SWITCH

Check the driver side door switch. Refer to 

DLK-96, "Component Inspection"

 (with Intelligent Key) or 

DLK-227,

"Component Inspection"

 (without Intelligent Key).

Is the inspection result normal?

YES

>> Replace the BCM. Refer to 

BCS-70, "Removal and Installation"

 (with Intelligent Key) or 

BCS-127,

"Removal and Installation"

 (without Intelligent Key).

NO

>> Replace driver side door switch. Refer to 

DLK-175, "Removal and Installation"

 (with Intelligent

Key) or 

DLK-301, "Removal and Installation"

 (without Intelligent Key).

Monitor Item

Condition

Status

BUZZER

Under the condition of buzzer input

ON

Except above

OFF

WCS

THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)

WCS-45

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)

Description

INFOID:0000000009654173

The key warning chime does not sound, when all of the following conditions are fulfilled.

• Key inserted into the key cylinder (key switch signal ON).

• Ignition switch is in ACC or OFF (ignition switch signal OFF).

• Driver side door is open (front door switch LH ON)

Diagnosis Procedure

INFOID:0000000009654174

1.

CHECK BCM INPUT SIGNAL

1. Connect CONSULT.

2. Select the DATA MONITOR of BCM(BUZZER) and check the KEY ON SW monitor value. Refer to 

BCS-

85, "BUZZER : CONSULT Function (BCM - BUZZER)"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-127, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK KEY SWITCH SIGNAL CIRCUIT

Check the key switch signal circuit. Refer to 

WCS-40, "Diagnosis Procedure"

. 

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-127, "Removal and Installation"

.

NO

>> Check applicable parts, and repair or replace corresponding parts.