Nissan Versa Note. Manual - part 421

EXL-68

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORKFLOW

YES

>> GO TO 5.

NO

>> GO TO 11.

11.

REPAIR CHECK (OPERATION CHECK)

Check the operation of each part.
Does it operate normally?

YES

>> Inspection End.

NO

>> GO TO 3.

POWER SUPPLY AND GROUND CIRCUIT

EXL-69

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DTC/CIRCUIT DIAGNOSIS

POWER SUPPLY AND GROUND CIRCUIT

BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis 
Procedure

INFOID:0000000009694253

Regarding Wiring Diagram information, refer to 

BCS-51, "Wiring Diagram"

.

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not blown.

Is the fuse blown?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M99.

2. Check voltage between BCM connector M99 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM connector M99 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair harness or connector.

BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag-
nosis Procedure

INFOID:0000000009694252

Regarding Wiring Diagram information, refer to 

BCS-111, "Wiring Diagram"

.

Terminal No.

Signal name

Fuses and fusible link No.

57

Battery power supply

12 (10A)

70

G (40A)

BCM

Ground

Voltage

Connector

Terminal

M99

57

—

Battery voltage

70

BCM

Ground

Continuity

Connector

Terminal

M99

67

—

Yes

EXL-70

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

1.

CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not blown.

Is the fuse blown?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connectors.

3. Check voltage between BCM connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM connector and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair harness or connector.

IPDM E/R (WITH INTELLIGENT KEY SYSTEM)
IPDM E/R (WITH INTELLIGENT KEY SYSTEM) : Diagnosis Procedure

INFOID:0000000009694254

Regarding Wiring Diagram information, refer to 

PCS-22, "Wiring Diagram"

.

1.

 CHECK FUSE AND FUSIBLE LINKS

Check that the following IPDM E/R fuse or fusible links are not blown.

Terminal No.

Signal name

Fuses and fusible link No.

37

Battery power supply

8 (10A)

42

12 (10A)

50

G (40A)

11

Ignition switch ACC or ON

18 (10A)

38

Ignition switch ON or START

2 (10A)

BCM

Ground

Ignition switch position

Connector

Terminal

—

OFF

ACC

ON

M18

11

0 V

Battery voltage

Battery voltage

37

Battery voltage

38

0 V

0 V

M19

42

Battery voltage

Battery voltage

50

BCM

Ground

Continuity

Connector

Terminal

M19

55

—

Yes

POWER SUPPLY AND GROUND CIRCUIT

EXL-71

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the fuse blown?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK BATTERY POWER SUPPLY CIRCUIT

1. Disconnect IPDM E/R connector E42.

2. Check voltage between IPDM E/R connector E42 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

 CHECK GROUND CIRCUIT

1. Disconnect IPDM E/R connectors E45 and E46.

2. Check continuity between IPDM E/R connectors and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

IPDM E/R (WITHOUT INTELLIGENT KEY SYSTEM)
IPDM E/R (WITHOUT INTELLIGENT KEY SYSTEM) : Diagnosis Procedure

INFOID:0000000009694255

Regarding Wiring Diagram information, refer to 

PCS-51, "Wiring Diagram"

.

1.

 CHECK FUSE AND FUSIBLE LINKS

Check that the following IPDM E/R fuse or fusible links are not blown.

Is the fuse blown?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit.

NO

>> GO TO 2.

Terminal No.

Signal name

Fuse and fusible link Nos.

1

Battery power supply

A (120A), E (80A)

2

B (60A)

IPDM E/R

Ground

Voltage

(Approx.)

Connector

Terminal

E42

1

—

Battery voltage

2

IPDM E/R

Ground

Continuity

Connector

Terminal

E45

19

Yes

E46

60

89

Terminal No.

Signal name

Fuse and fusible link Nos.

1

Battery power supply

A (120A), E (80A)

2

B (60A)

10

Ignition switch ON or START

2 (10A)