Nissan Versa Note. Manual - part 97

 

  Index      Nissan     Nissan Versa Note (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  95  96  97  98   ..

 

 

Nissan Versa Note. Manual - part 97

 

 

BCS

COMBINATION SWITCH SYSTEM SYMPTOMS

BCS-125

< SYMPTOM DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

SYMPTOM DIAGNOSIS

COMBINATION SWITCH SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000009693657

WITH VARIABLE INTERMITTENT FRONT WIPERS

1. Perform the data monitor of CONSULT to check for any malfunctioning item.
2. Check the malfunction combinations.

Malfunction item: 

×

3. Identify the malfunctioning part from the agreed combination and repair or replace the part.

WITHOUT VARIABLE INTERMITTENT FRONT WIPERS

1. Perform the data monitor of CONSULT to check for any malfunctioning item.

Malfunction combination

Data monitor item

FR WIPER 

HI

FR W

IPER LOW

FR W

ASHER 

SW

FR W

IPER I

N

T

INT VOLUM

E

RR WIPER ON

RR W

IPER INT

RR W

ASHER SW

T

U

R

N

 SIGNAL R

TURN SIG

NA

L L

TA

IL

 L

A

M

P

 S

W

HI BE

AM 

SW

HEA

D

 LAMP SW

 1

HEA

D

 LAMP SW

 2

PA

S

S

IN

G

 S

W

FR FOG SW

A

×

×

×

×

B

×

×

×

×

C

×

×

×

×

D

×

×

×

E

×

×

×

F

×

×

×

G

×

×

×

×

H

×

×

I

×

×

×

×

J

×

×

×

×

K

All Items

L

If only one item is detected or the item is not applicable to the combinations A to K 

Malfunction 

combination

Malfunctioning part

Repair or replace

A

Combination switch INPUT 1 circuit

Inspect the combination switch input circuit applicable to the malfunctioning 
part. Refer to 

BCS-121, "Diagnosis Procedure"

.

B

Combination switch INPUT 2 circuit

C

Combination switch INPUT 3 circuit

D

Combination switch INPUT 4 circuit

E

Combination switch INPUT 5 circuit

F

Combination switch OUTPUT 1 circuit

Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to 

BCS-123, "Diagnosis Procedure"

.

G

Combination switch OUTPUT 2 circuit

H

Combination switch OUTPUT 3 circuit

I

Combination switch OUTPUT 4 circuit

J

Combination switch OUTPUT 5 circuit

K

BCM

Replace BCM. Refer to 

BCS-127, "Removal and Installation"

.

L

Combination switch

Replace the combination switch. Refer to 

BCS-128, "Removal and Installa-

tion"

.

BCS-126

< SYMPTOM DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

COMBINATION SWITCH SYSTEM SYMPTOMS

2. Check the malfunction combinations.

Malfunction item: 

×

3. Identify the malfunctioning part from the agreed combination and repair or replace the part.

Malfunction combination

Data monitor item

FR WI

PER HI

FR W

IPE

R L

O

W

FR W

ASHE

R

 SW

FR WIP

ER INT

R

R

 WIPER ON

RR WIPE

R

 INT

RR W

ASHER 

SW

TURN SIGNAL R

TURN SIGNAL L

TA

IL

 LA

MP S

W

HI

 BEAM SW

HEAD LAMP

 SW 1

HEAD LAMP

 SW 2

P

ASSING S

W

A

×

×

×

×

B

×

×

×

×

C

×

×

×

D

×

×

E

×

F

×

×

G

×

×

×

H

×

×

I

×

×

×

J

×

×

×

×

K

All Items

L

If only one item is detected or the item is not applicable to the combinations A to K 

Malfunction 

combination

Malfunctioning part

Repair or replace

A

Combination switch INPUT 1 circuit

Inspect the combination switch input circuit applicable to the malfunctioning 
part. Refer to 

BCS-121, "Diagnosis Procedure"

.

B

Combination switch INPUT 2 circuit

C

Combination switch INPUT 3 circuit

D

Combination switch INPUT 4 circuit

E

Combination switch INPUT 5 circuit

F

Combination switch OUTPUT 1 circuit

Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to 

BCS-123, "Diagnosis Procedure"

.

G

Combination switch OUTPUT 2 circuit

H

Combination switch OUTPUT 3 circuit

I

Combination switch OUTPUT 4 circuit

J

Combination switch OUTPUT 5 circuit

K

BCM

Replace BCM. Refer to 

BCS-127, "Removal and Installation"

.

L

Combination switch

Replace the combination switch. Refer to 

BCS-128, "Removal and Installa-

tion"

.

BCS

BCM (BODY CONTROL MODULE)

BCS-127

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

REMOVAL AND INSTALLATION

BCM (BODY CONTROL MODULE)

Removal and Installation

INFOID:0000000009693690

REMOVAL

CAUTION:

Before replacing BCM, perform “READ CONFIGURATION” to save or print current vehicle specifica-

tion. Refer to 

BCS-116, "Description"

.

1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to 

PG-67,

"Removal and Installation (Battery)"

.

2. Remove instrument lower panel LH. Refer to 

IP-24, "Removal and Installation"

.

3. Remove screws (A) and remove the BCM (1) from the steering

member and position aside.

: Front

4. Disconnect the harness connectors from the BCM.
5. Remove relays from relay bracket.
6. Remove relay bracket from BCM to transfer to new BCM.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Perform “CONFIGURATION (BCM)” when replacing BCM. Refer to 

BCS-116, "Description"

.

• Make sure to perform the system initialization (NATS) (if equipped) when replacing BCM. Refer to

BCS-115, "Work Procedure"

.

• When replacing BCM, if new BCM does not come with keyfobs attached, all existing keyfobs must be

re-registered. 

ALMIA0656ZZ

BCS-128

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

COMBINATION SWITCH

COMBINATION SWITCH

Removal and Installation

INFOID:0000000009693691

CAUTION:

• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least

three minutes.

• Do not use air or electric tools when removing or installing the combination switch.

REMOVAL

1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to 

PG-67,

"Removal and Installation (Battery)"

.

2. Remove the steering column covers. Refer to 

IP-17, "Removal and Installation"

.

3. Rotate steering wheel clockwise to access first combination

switch screw (A) and remove.

4. Rotate steering wheel counter-clockwise to access second com-

bination switch screw (A) and remove.

5. Disconnect the harness connector (B) from the combination

switch (1) and remove.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.

• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function

and delete the memory with CONSULT.

• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-

tions. Refer to 

BCS-115, "Work Procedure"

.

ALMIA0648ZZ

ALMIA0649ZZ

 

 

 

 

 

 

 

Content   ..  95  96  97  98   ..