Nissan Rogue. Manual - part 1195

TM-152

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P084D TRANSMISSION FLUID PRESSURE SEN/SW H

Is the inspection result normal?

YES >> INSPECTION 

END

NO

>> GO TO 2.

2.

CHECK PRIMARY PRESSURE SENSOR POWER CIRCUIT

1. Turn ignition switch OFF.

2. Connect TCM connector.

3. Disconnect CVT unit connector.

4. Turn ignition switch ON.

5. Check voltage between CVT unit harness connector terminal and ground.

Is the inspection result normal?

YES 

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK PRIMARY PRESSURE SENSOR SIGNAL CIRCUIT

Check voltage between CVT unit harness connector terminal and ground.

Is the inspection result normal?

YES  >> There is malfunction of primary pressure sensor. Replace transaxle assembly. Refer to 

TM-220,

"Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

+

−

Condition

Voltage

TCM

Connector

Terminal

F75

17

Ground

• After engine warm up
• Selector lever: “N” position
• At idle

0.75 – 0.82 V

+

−

Voltage

(Approx.)

CVT unit

Connector

Terminal

F74

22

Ground

5.0 V

+

−

Voltage

(Approx.)

CVT unit

Connector

Terminal

F74

13

Ground

0 V

P0863 TCM COMMUNICATION

TM-153

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0863 TCM COMMUNICATION

DTC Description

INFOID:0000000011279373

DTC DETECTION LOGIC

POSSIBLE CAUSE

TCM

FAIL-SAFE

• Selector shock is large

• Start  is  slow

• Acceleration is slow

• Lock-up is not performed

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Check the DTC.
Is “P0863” detected?

YES

>> Go to 

TM-153, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279374

1.

REPLACE TCM

Replace TCM. Refer to 

TM-202, "Removal and Installation"

.

>> WORK END

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0863

CONTROL UNIT (CAN)
(TCM Communication Circuit)

An error is detected at the initial CAN diagnosis of TCM. 

TM-154

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0890 TCM

P0890 TCM

DTC Description

INFOID:0000000011279375

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector [TCM power supply (back-up) circuit is open or shorted]

• TCM

FAIL-SAFE

• Selector shock is large

• Start  is  slow

• Acceleration is slow

• Lock-up is not performed

• Vehicle speed is not increased

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine and wait for 5 seconds or more.

2. Check the DTC.
Is “P0890” detected?

YES

>> Go to 

TM-154, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279376

1.

CHECK TCM POWER SUPPLY (BACK-UP) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check voltage between TCM harness connector terminals and ground.

Is the inspection result normal?

YES 

>> Replace TCM. Refer to 

TM-202, "Removal and Installation"

.

NO

>> GO TO 2.

2.

DETECT MALFUNCTIONING ITEMS

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0890

TCM
(Transmission Control Module Power Relay 
Sense Circuit Low)

When all of the following conditions are satisfied and this state is main-
tained for 0.2 seconds:
• TCM power supply voltage: More than 11 V
• Battery voltage: Less than 8.4 V

+

−

Voltage

TCM

Connector

Terminal

F75

45

Ground

10 – 16 V

46

P0890 TCM

TM-155

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Check the following items:

• Open circuit or short circuit in harness between battery positive terminal and TCM connector terminals 45,

and 46.

• 10A fuse (No.59, located in the fuse and fusible link block). Refer to 

PG-65, "Terminal Arrangement"

.

Is the inspection result normal?

YES >> INSPECTION 

END

NO

>> Repair or replace malfunctioning parts.