Nissan Rogue. Manual - part 1189

 

  Index      Nissan     Nissan Rogue (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1187  1188  1189  1190   ..

 

 

Nissan Rogue. Manual - part 1189

 

 

TM-128

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0717 INPUT SPEED SENSOR A

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P0717” detected?

YES

>> Go to 

TM-128, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279348

1.

CHECK INPUT SPEED SENSOR POWER CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect input speed sensor connector.

3. Turn ignition switch ON.

4. Check voltage between input speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> GO TO 6.

2.

CHECK INPUT SPEED SENSOR GROUND CIRCUIT 

Check continuity between input speed sensor harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between input speed sensor harness connector terminal and TCM harness connector

terminal.

Is the inspection result normal?

YES 

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 2)

Check continuity between input speed sensor harness connector terminal and ground. 

Selector lever

: “D” position

Engine speed

: 1,200 rpm or more

Vehicle speed

: 40 km/h (25 MPH) or more

+

Voltage

Input speed sensor

Connector

Terminal

F73

3

Ground

10 – 16 V

Input speed sensor

Continuity

Connector

Terminal

F73

1

Ground

Existed

Input speed sensor

TCM

Continuity

Connector

Terminal

Connector

Terminal

F73

2

F75

24

Existed

P0717 INPUT SPEED SENSOR A

TM-129

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES 

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK TCM INPUT SIGNALS

1. Connect all of disconnected connectors.

2. Lift the vehicle.

3. Start the engine.

4. Check frequency of input speed sensor.

Is the inspection result normal?

YES >> INSPECTION 

END

NO

>> Replace input speed sensor. Refer to 

TM-207, "Removal and Installation"

.

6.

CHECK CIRCUIT BETWEEN IPDM E/R AND INPUT SPEED SENSOR

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector terminal and input speed sensor harness connec-

tor terminals.

Is the check result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-24, "Wiring Dia-

gram — Ignition Power Supply —"

.

• Short circuit in harness between IPDM E/R harness connector terminal 70 and input speed sensor harness

connector terminal 3.

• 10A fuse (No.46, located in the IPDM E/R). Refer to 

PG-68, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning parts.

Input speed sensor

Continuity

Connector

Terminal

F73

2

Ground

Not existed

+

Condition

Frequency

(Approx.)

TCM

Connector

Terminal

F75

24

Ground

• Shift position: “L” position
• Vehicle speed: 20 km/h (12 MPH)

880 Hz

JSDIA3769GB

IPDM E/R harness connector

Input speed sensor

Continuity

Connector

Terminal

Connector

Terminal

F35

70

F73

3

Existed

TM-130

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0740 TORQUE CONVERTER

P0740 TORQUE CONVERTER

DTC Description

INFOID:0000000011279349

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector (Torque converter clutch solenoid valve circuit is open or shorted to power supply)

• Torque converter clutch solenoid valve

FAIL-SAFE

• Start  is  slow

• Acceleration is slow

• Lock-up is not performed

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PREPARATION BEFORE OPERATION

With CONSULT

1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “FLUID TEMP”.

4. Confirm that the CVT fluid temperature is in the following range. 

With GST

1. Start the engine.

2. Set the CVT fluid to 20

°C (68°F) or more. 

NOTE:

When the ambient temperature is 20

°C (68°F), the CVT fluid usually increases to 50 to 80°C (122 to

176

°F) with driving in an urban area for approximately 10 minutes. 

Is the CVT fluid 20

°C (68°F) or more? 

YES

>> GO TO 3.

NO

>> 1. Warm the transaxle. 

2. GO TO 3.

3.

CHECK DTC DETECTION

1. Drive the vehicle.

2. Maintain the following conditions for 10 seconds or more.

3. Stop the vehicle.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0740

TORQUE CONVERTER
(Torque Converter Clutch Circuit/Open)

When all of the following conditions are satisfied and this state is main-
tained for 5 seconds:
• TCM power supply voltage: More than 11 V
• P0743 is not detected.
• TCM judges that solenoid valve circuit is open.

FLUID TEMP

: 20

°C (68°F) or more

Selector lever

: “D” position

Vehicle speed

: 40 km/h (25 MPH) or more

P0740 TORQUE CONVERTER

TM-131

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

4. Check the first trip DTC.
Is “P0740” detected?

YES

>> Go to 

TM-131, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000011279350

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector.

3. Check continuity between TCM harness connector terminal and CVT unit harness connector terminal.

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace malfunctioning parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check resistance between CVT unit harness connector terminal and ground.

Is the inspection result normal?

YES >> INSPECTION 

END

NO

>> There is malfunction of torque converter clutch solenoid valve. Replace transaxle assembly. Refer

to 

TM-220, "Removal and Installation"

.

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F75

38

F74

5

Existed

CVT unit

Condition

Resistance

Connector

Terminal

F209

5

Ground

CVT fluid temperature: 20

°C (68°F)

5.5 – 7.0 

CVT fluid temperature: 50

°C (122°F)

6.0 – 8.0 

CVT fluid temperature: 80

°C (176°F)

6.5 – 8.5 

 

 

 

 

 

 

 

Content   ..  1187  1188  1189  1190   ..