Content .. 1163 1164 1165 1166 ..

Nissan Rogue. Manual - part 1165

TM-32

< SYSTEM DESCRIPTION >

[CVT: RE0F10D]

SYSTEM

*: If these input/output signals show errors, TCM activates the fail-safe function.

CVT CONTROL SYSTEM : Fail-safe

INFOID:0000000011279272

TCM has a fail-safe mode. The mode functions so that operation can be continued even if the signal circuit of

the main electronically controlled input/output parts is damaged.

If the vehicle shows following behaviors including “poor acceleration”, a malfunction of the applicable system

is detected by TCM and the vehicle may be in a fail-safe mode. At this time, check the DTC code and perform

inspection and repair according to the malfunction diagnosis procedures.

Fail-safe function

Control Item

Shift control

Line pressure

control

Select control

Lock-up con-

trol

Fail-safe func-

tion*

Input

Engine torque signal
(CAN communication)

Engine speed signal
(CAN communication)

Accelerator pedal position signal
(CAN communication)

Closed throttle position signal
(CAN communication)

Stop lamp switch signal
(CAN communication)

Primary pressure sensor

Secondary pressure sensor

CVT fluid temperature sensor

Primary speed sensor

Output speed sensor

Input speed sensor

Transmission range switch

Overdrive control switch
(CAN communication)

Output

Line pressure solenoid valve

Primary pressure solenoid valve

Torque converter clutch solenoid
valve

Secondary pressure solenoid valve

Select solenoid valve

Shift position indicator
(CAN communication)

O/D OFF indicator lamp
(CAN communication)

DTC

Vehicle behavior

Conditions of vehicle

P062F

Not changed from normal driving

—

P0705

• Shift position indicator on combination meter is not dis-

played

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

SYSTEM

TM-33

< SYSTEM DESCRIPTION >

[CVT: RE0F10D]

P0706

• Shift position indicator on combination meter is not dis-

played

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0711

• Start is slow
• Acceleration is slow

Engine coolant temperature when engine start:
Temp.

≥ 10°C (50°F)

• Selector shock is large
• Start is slow
• Acceleration is slow

Engine coolant temperature when engine start:
−35°C (−31°F) ≤ Temp. < 10°C (50°F)

• Selector shock is large
• Start is slow
• Acceleration is slow

Engine coolant temperature when engine star:
Temp. <

−35°C (−31°F)

P0712

• Start is slow
• Acceleration is slow

Engine coolant temperature when engine start:
Temp.

≥ 10°C (50°F)

• Selector shock is large
• Start is slow
• Acceleration is slow

Engine coolant temperature when engine start:
−35°C (−31°F) ≤ Temp. < 10°C (50°F)

• Selector shock is large
• Start is slow
• Acceleration is slow

Engine coolant temperature when engine star:
Temp. <

−35°C (−31°F)

P0713

• Start is slow
• Acceleration is slow

Engine coolant temperature when engine start:
Temp.

≥ 10°C (50°F)

• Selector shock is large
• Start is slow
• Acceleration is slow

Engine coolant temperature when engine start:
−35°C (−31°F) ≤ Temp. < 10°C (50°F)

• Selector shock is large
• Start is slow
• Acceleration is slow

Engine coolant temperature when engine star:
Temp. <

−35°C (−31°F)

P0715

• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0717

• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0740

• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0743

• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0744

• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0746

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

DTC

Vehicle behavior

Conditions of vehicle

TM-34

< SYSTEM DESCRIPTION >

[CVT: RE0F10D]

SYSTEM

P0776

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
• Vehicle speed is not increased

When a malfunction occurs on the low oil pressure side

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

When a malfunction occurs on the high oil pressure side

P0778

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0779

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0841

Not changed from normal driving

—

P0847

Not changed from normal driving

—

P0848

Not changed from normal driving

—

P084C

Not changed from normal driving

—

P084D

Not changed from normal driving

—

P0863

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0890

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
• Vehicle speed is not increased

—

P0962

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0963

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0965

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

When a malfunction occurs on the low oil pressure side

• Selector shock is large
• Lock-up is not performed

When a malfunction occurs on the high oil pressure side

P0966

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P0967

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

P2765

• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

DTC

Vehicle behavior

Conditions of vehicle

SYSTEM

TM-35

< SYSTEM DESCRIPTION >

[CVT: RE0F10D]

CVT CONTROL SYSTEM : Protection Control

INFOID:0000000011279273

The TCM becomes the protection control status temporarily to protect the safety when the safety of TCM and

transmission is lost. It automatically returns to the normal status if the safety is secured.

The TCM has the following protection control.

CONTROL FOR WHEEL SPIN

TORQUE IS REDUCED WHEN DRIVING WITH THE REVERSE GEAR

CONTROL WHEN FLUID TEMPERATURE IS HIGH

P2813

• Selector shock is large
• Start is slow
• Acceleration is slow
• Vehicle speed is not increased

When a malfunction occurs on the low oil pressure side

• Selector shock is large

When a malfunction occurs on the high oil pressure side

P2814

Selector shock is large

—

P2815

Selector shock is large

—

U0073

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

U0100

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

U0102

Not changed from normal driving

—

U0140

Not changed from normal driving

—

U0141

Not changed from normal driving

—

U0155

Not changed from normal driving

—

U0300

• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed

—

U1000

Not changed from normal driving

—

U110F

Not changed from normal driving

—

U1111

Not changed from normal driving

—

U1117

Not changed from normal driving

—

DTC

Vehicle behavior

Conditions of vehicle

Control

When a wheel spin is detected, the engine output and gear ratio are limited and the line pressure is increased.
Limits engine output when a wheel spin occurs in any of right and left drive wheels.

Vehicle behavior in
control

If the accelerator is kept depressing during wheel spin, the engine revolution and vehicle speed are limited to
a certain degree.

Normal return condi-
tion

Wheel spin convergence returns the control to the normal control.

Control

Engine output is controlled according to a vehicle speed while reversing the vehicle.

Vehicle behavior in
control

Power performance may be lowered while reversing the vehicle.

Normal return condi-
tion

Torque returns to normal by positioning the selector lever in a range other than “R” position.

Content .. 1163 1164 1165 1166 ..