Nissan Rogue. Manual - part 1135

SRC-90

< DTC/CIRCUIT DIAGNOSIS >

B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR

B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR

DTC Logic

INFOID:0000000011279591

DTC DETECTION LOGIC 

With CONSULT

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.

CHECK SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Check for DTC using CONSULT.
Is the DTC detected?

YES (Current DTC)>>Refer to 

SRC-90, "Diagnosis Procedure"

.

YES (Past DTC)>>GO TO 2.

NO

>> Inspection End.

2.

ERASE SELF DIAGNOSTIC RESULT

Erase the DTC using CONSULT.
Can the DTC be erased?

YES

>> Inspection End.

NO

>> Refer to 

SRC-90, "Diagnosis Procedure"

.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.

CHECK SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:

SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?

YES

>> Refer to 

SRC-90, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011279592

1.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

• Visible damage to connector or terminal

• Loose terminal

• Poor connection

NOTE:

All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors).

Is the inspection result normal?

CONSULT name

DTC

DTC detecting condition

Repair order

PASSENGER AIRBAG INDICATOR CIRCUIT

[FAIL]

B00D5

Front passenger air bag OFF indica-
tor is malfunctioning.

Refer to 

SRC-90, "Diagnosis Proce-

dure"

.

PASSENGER AIRBAG INDICATOR CIRCUIT

[OPEN]

Front passenger air bag OFF indica-
tor circuit is open.

PASSENGER AIRBAG INDICATOR CIRCUIT

[VB-SHORT]

Front passenger air bag OFF indica-
tor is shorted to a power supply cir-
cuit.

PASSENGER AIRBAG INDICATOR CIRCUIT

[GND-SHORT]

Front passenger air bag OFF indica-
tor is shorted to ground.

B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR

SRC-91

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 2.

NO

>> Perform one of the following repairs:

• Visible damage: Replace the harness.

• Loose terminal: Secure the terminal.

• Poor connection: Secure the connection.

2.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 3.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

3.

WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:

The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors).
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace the harness.

4.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 5.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

5.

FRONT PASSENGER AIR BAG OFF INDICATOR

1. Replace the front passenger air bag off indicator.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 6.

NO

>> Clear DTC. Inspection End.

6.

AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace the air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 7.

NO

>> Clear DTC. Inspection End.

7.

RELATED HARNESS

Replace the related harness.

>> END

SRC-92

< DTC/CIRCUIT DIAGNOSIS >

B142A IGNITION VOLTAGE

B142A IGNITION VOLTAGE

Description

INFOID:0000000011279593

DTC B142A IGNITION VOLTAGE

Ignition voltage is supplied to the air bag diagnosis sensor unit when the ignition is in the ON position. The air

bag diagnosis sensor unit will monitor for low or high ignition voltage.

PART LOCATION

Refer to 

SRC-5, "Component Parts Location"

.

DTC Logic

INFOID:0000000011279594

DTC DETECTION LOGIC 

With CONSULT

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF DIAGNOSTIC RESULT

Check for the DTC on CONSULT.
Is the DTC detected?

YES

>> Refer to 

SRC-92, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011279595

NOTE:

Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is

eliminated using air bag warning lamp each time repair is finished. If malfunction is still observed, proceed to

the next step. When malfunction is eliminated, further repair work is not required.

1.

HARNESS CONNECTOR

Is there any visible damage to the connector?
Is the inspection result normal?

YES

>> Replace the harness.

NO

>> GO TO 2.

2.

WIRING HARNESS

Is there any visible damage to the harness?
Is the inspection result normal?

YES

>> Replace the harness.

NO

>> GO TO 3.

3.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT name

DTC

DTC detecting condition

Repair order

IGN VOLTAGE

[LOW]

B142A

Ignition voltage low at air bag diagnosis sensor unit. Refer to 

SRC-92, "Diagnosis Procedure"

.

IGN VOLTAGE

[HIGH]

Ignition voltage high at air bag diagnosis sensor unit.

B142A IGNITION VOLTAGE

SRC-93

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

Replace the air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

>> GO TO 4.

4.

RELATED HARNESS

Replace the related harness.

>> END