Nissan Rogue. Manual - part 1123

SRC-42

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

• Air bag warning lamp blinks in user mode only.

• Air bag sensor unit does not record whether or not zero point reset is performed.
Is condition “ALREADY PERFORMED”?

YES

>> Print out “ZERO POINT RESET CURRENT STATUS” screen, and inspection end.

NO

>> Check condition as per the following, and perform “Zero point reset” again:

• Passenger seat is occupied by an object.

• Excessive vibration is applied while performing “Zero point reset”.

• Occupant detection system is malfunctioning.

NOTE:

If “Incomplete” is displayed on “Zero point reset current status”, “Zero point reset” is not com-

pleted normally. Check the condition as per the following and perform “Zero point reset” again:

• Passenger seat is occupied by an object.

• Excessive vibration is applied while performing “Zero point reset”.

• Occupant detection system is malfunctioning.

CONFIGURATION
CONFIGURATION : Description

INFOID:0000000011279540

When replacing air bag diagnosis sensor unit, save or print current vehicle specification with CONSULT con-

figuration before replacement.

NOTE:

If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-

ing air bag diagnosis sensor unit.

CONFIGURATION : Work Procedure

INFOID:0000000011279541

CAUTION:

• When replacing ECU, you must perform “Write Configuration” with CONSULT.

- Complete the procedure of “Write Configuration” in order.

- If you set incorrect “Write Configuration”, incidents might occur.

- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

- Never perform “Write Configuration” except for new air bag diagnosis sensor unit.

• When replacing BCM, perform the system initialization (NATS).

CONFIGURATION

Vehicle specification needs to be written with CONSULT because it is not written after replacing air bag diag-

nosis sensor unit.

Configuration has three functions as follows:

CAUTION:

• When replacing air bag diagnosis sensor unit, you must perform “Select Saved Data List” or "After

Replace ECU" with CONSULT.

• Complete the procedure of “Select Saved Data List” or "After Replace ECU" in order.

• If you set incorrect “Select Saved Data List” or "After Replace ECU", incidents might occur.

• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

• Never perform “Select Saved Data List” or "After Replace ECU" except for new air bag diagnosis

sensor unit. 

1.

SAVING VEHICLE SPECIFICATION

CONSULT

Enter "Re/Programming, Configuration" and perform “Before Replace ECU” to save or print current vehicle

specification.

NOTE:

If “Before Replace ECU” cannot be used, use the "After Replace ECU" or "Manual Configuration" after replac-

ing BCM.

Function

Description

"Before Replace ECU"

• Reads the vehicle configuration of current air bag diagnosis sensor unit.
• Saves the read vehicle configuration.

"After Replace ECU"

Writes the vehicle configuration with manual selection.

"Select Saved Data List"

Writes the vehicle configuration with saved data.

INSPECTION AND ADJUSTMENT

SRC-43

< BASIC INSPECTION >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

>> GO TO 2.

2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to 

SR-26, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT

1. Enter "Re/Programming, Configuration".

2. If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will

be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle

specification.

3. If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-

tion" to write vehicle specification.

-

Select “After Replace ECU” or “Manual Configuration”.

-

Identify the correct model and configuration list.

-

Confirm and/or change setting value for each item.

CAUTION:

Thoroughly read and understand the vehicle specification. ECU control may not operate normally if

the setting is not correct.

-

Select “Next”.

CAUTION:

Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated configu-

ration of brand new air bag diagnosis sensor unit is same as the desirable configuration. If not,

configuration which is set automatically by selecting vehicle model cannot be memorized.

-

When "Completed", select "End".

>> GO TO 4.

4.

OPERATION CHECK

Confirm that each function controlled by air bag diagnosis sensor unit.

>> Work End.

SRC-44

< BASIC INSPECTION >

INTERMITTENT INCIDENT

INTERMITTENT INCIDENT

Inspection Procedure

INFOID:0000000011279542

INTERMITTENT TROUBLE

An intermittent incident may have occurred in the past but is not being detected currently. This DTC will not be

detected on “Self Diagnostic Result [CURRENT]”, but may be viewed on “Self Diagnostic Result [PAST]” if the

DTC has not been erased. Refer to 

SRC-16, "Trouble Diagnosis with CONSULT"

.

B0001, B0002 DRIVER AIRBAG MODULE

SRC-45

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DTC/CIRCUIT DIAGNOSIS

B0001, B0002 DRIVER AIRBAG MODULE

DTC Logic

INFOID:0000000011279543

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.

CHECK SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Check for DTC using CONSULT.
Is the DTC detected?

YES (Current DTC)>>Refer to 

SRC-46, "Diagnosis Procedure"

.

YES (Past DTC)>>GO TO 2.

NO

>> Inspection End.

2.

ERASE SELF DIAGNOSTIC RESULT

Erase the DTC using CONSULT.
Can the DTC be erased?

YES

>> Inspection End.

NO

>> Refer to 

SRC-46, "Diagnosis Procedure"

.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.

CHECK SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-14, "On Board Diagnosis Function"

.

NOTE:

SRS will not enter diagnosis mode if no malfunction is detected in user mode.

CONSULT name

DTC

DTC detecting condition

Repair order

DRIVER AIRBAG MODULE CIRCUIT 

[OPEN]

B0001

Driver air bag module circuit 
(DR1) is open
(including the spiral cable).

Refer to 

SRC-46, "Diagnosis Proce-

dure"

.

DRIVER AIRBAG MODULE CIRCUIT 

[VB-SHORT]

Driver air bag module circuit 
(DR1) is shorted to a power sup-
ply circuit
(including the spiral cable).

DRIVER AIRBAG MODULE CIRCUIT 

[GND-SHORT]

Driver air bag module circuit 
(DR1) is shorted to ground
(including the spiral cable).

DRIVER AIRBAG MODULE CIRCUIT 

[SHORT]

Driver air bag module circuits 
(DR1) are shorted to each other
(including the spiral cable).

DRIVER AIRBAG MODULE 2ND CIRCUIT 

[OPEN]

B0002

Driver air bag module circuit 
(DR2) is open
(including the spiral cable).

DRIVER AIRBAG MODULE 2ND CIRCUIT 

[VB-SHORT]

Driver air bag module circuit 
(DR2) is shorted to a power sup-
ply circuit
(including the spiral cable).

DRIVER AIRBAG MODULE 2ND CIRCUIT 

[GND-SHORT]

Driver air bag module circuit 
(DR2) is shorted to ground
(including the spiral cable).

DRIVER AIRBAG MODULE 2ND CIRCUIT 

[SHORT]

Driver air bag module circuits 
(DR2) are shorted to each other
(including the spiral cable).