Nissan Rogue. Manual - part 1095

INSPECTION AND ADJUSTMENT

SEC-159

< BASIC INSPECTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000011278558

Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.

ECM RE-COMMUNICATING FUNCTION
ECM RE-COMMUNICATING FUNCTION : Description

INFOID:0000000011278559

Performing following procedure can automatically perform re-communication of ECM and BCM, but only when

the ECM has been replaced with a new one (*1).

*1: New one means an ECM which has never been energized on-board.

(In this step, initialization procedure by CONSULT is not necessary)

NOTE:

• When registering new Key IDs or replacing the ECM that is not brand new, refer to CONSULT Immobi-

lizer mode and follow the on-screen instructions.

• If multiple keys are attached to the key holder, separate them before work.

• Distinguish keys with unregistered key ID from those with registered ID.

ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement

INFOID:0000000011278560

1.

PERFORM ECM RE-COMMUNICATING FUNCTION

1. Install ECM.

2. Using a registered key (*2), turn ignition switch to “ON”.

*2: To perform this step, use the key that has been used before performing ECM replacement.

3. Maintain ignition switch in “ON” position for at least 5 seconds.

4. Turn ignition switch to “OFF”.

5. Start engine.
Can engine be started?

YES

>> Procedure is completed.

NO

>> Initialize control unit. Refer to CONSULT Immobilizer mode and follow the on-screen instructions.

2015 Rogue NAM

SEC-160

< BASIC INSPECTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

KEYFOB ID REGISTRATION

KEYFOB ID REGISTRATION

Description

INFOID:0000000011278561

Perform system initialization when replacing BCM, replacing keyfob or registering an additional keyfob. Refer

to the CONSULT Immobilizer mode and follow the on-screen instructions.

2015 Rogue NAM

P1610 LOCK MODE

SEC-161

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

DTC/CIRCUIT DIAGNOSIS

P1610 LOCK MODE

Description

INFOID:0000000011278563

ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times

or more while communication between ECM and BCM is not normal.

DTC Logic

INFOID:0000000011278564

DTC DETECTION LOGIC

NOTE:

• If DTC B1610 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC B1610 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” of “ENGINE” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-161, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278565

1.

CHECK ENGINE START FUNCTION

1. Check that there are no DTC’s except for DTC P1610 detected.

If detected, erase the DTC after fixing.

2. Turn ignition switch OFF.

3. Insert the registered key into the ignition switch and wait 5 seconds.

4. Turn ignition switch ON.

5. Turn ignition switch OFF and wait 5 seconds.

6. Repeat steps 3 and 5 twice (a total of 3 times).

7. Check that engine can start.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1610

LOCK MODE

When ECM detects a communication malfunction between 
ECM and BCM 5 times or more.

—

2015 Rogue NAM

SEC-162

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

P1611 ID DISCORD, IMMU-ECM

P1611 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000011278566

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” of “ENGINE” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-162, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278567

1.

PERFORM INITIALIZATION

Perform initialization of BCM and reregistration of all keys using CONSULT. Refer to the CONSULT Immobi-

lizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with reregistered key?

YES

>> Inspection End.

NO

>> GO TO 2.

2.

CHECK SELF DIAGNOSTIC RESULT

1. Select “Self Diagnostic Result” of “ENGINE” using CONSULT.

2. Erase DTC.

3. Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to 

SEC-162, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 3.

NO

>> Inspection End.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all keys using CONSULT. Refer to the CONSULT Immobi-

lizer mode and follow the on-screen instructions.

Can the system be initialized and can the engine be started with registered key?

YES

>> Inspection End.

NO

>> GO TO 4.

4.

REPLACE ECM

1. Replace ECM. Refer to 

EC-502, "Removal and Installation"

.

2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”. Refer to 

EC-139, "Work Procedure"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1611

ID DISCORD, IMMU-ECM

The ID verification results between BCM 
and ECM are NG.

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• BCM
• ECM

2015 Rogue NAM