Nissan Rogue. Manual - part 1082

SECURITY INDICATOR LAMP

SEC-107

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SECURITY INDICATOR LAMP

Component Function Check

INFOID:0000000011278522

1.

CHECK FUNCTION

1. Perform “THEFT IND” in “Active Test” of “IMMU” of “BCM” using CONSULT.

2. Check security indicator lamp operation.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Go to 

SEC-107, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011278523

Regarding Wiring Diagram information, refer to 

SEC-50, "Wiring Diagram"

.

1.

CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect combination meter connector.

3. Check voltage between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO-1 >> Check 10 A fuse [No. 13, located in the fuse block (J/B)].

NO-2 >> Check harness for open or short between combination meter and fuse.

2.

CHECK SECURITY INDICATOR LAMP SIGNAL

1. Connect combination meter connector.

2. Disconnect BCM connector.

3. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 4.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

>> Inspection End.

Test item

Description

THEFT IND

ON

Security indicator lamp

Illuminates

OFF

Does not illuminate

(+)

(–)

Voltage (V)

(Approx.)

Combination meter

Connector

Terminal

M77

45

Ground

Battery voltage

(+)

(–)

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M18

35

Ground

Battery voltage

2015 Rogue NAM

SEC-108

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP

4.

CHECK SECURITY INDICATOR LAMP CIRCUIT

1. Disconnect combination meter connector.

2. Check continuity between combination meter harness connector and BCM harness connector.

3. Check continuity between combination meter harness connector and ground.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Repair or replace harness.

Combination meter

BCM

Continuity

Connector

Terminal

Connector

Terminal

M76

7

M18

35

Yes

Combination meter

Ground

Continuity

Connector

Terminal

M76

7

No

2015 Rogue NAM

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE

SEC-109

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SYMPTOM DIAGNOSIS

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE

Description

INFOID:0000000011278524

Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.

NOTE:

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

• The engine start function, door lock function, power distribution system, and NATS-NVIS in the Intelligent

Key system are closely related to each other regarding control. The vehicle security function can operate

only when the door lock and power distribution system are operating normally.

Conditions of Vehicle (Operating Conditions)

• “ENGINE START BY I-KEY” in “Work support” is “ON” when setting on CONSULT.

• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.

Diagnosis Procedure

INFOID:0000000011278525

1.

PERFORM WORK SUPPORT

Perform “INSIDE ANT DIAGNOSIS” on “Work support” in “INTELLIGENT KEY”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?

YES

>> Refer to 

BCS-47, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch.

Refer to 

SEC-85, "Component Inspection"

.

Is the operation normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> GO TO 1.

2015 Rogue NAM

SEC-110

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

Description

INFOID:0000000011278526

Security indicator lamp does not blink when ignition switch is in a position other than ON

NOTE:

• Before performing the diagnosis, check “Work Flow”. Refer to 

SEC-63, "Work Flow"

.

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

Conditions of Vehicle (Operating Conditions)

Ignition switch is not in the ON position.

Diagnosis Procedure

INFOID:0000000011278527

1.

CHECK SECURITY INDICATOR LAMP

Check security indicator lamp.

Refer to 

SEC-107, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> GO TO 1.

2015 Rogue NAM