Nissan Rogue. Manual - part 1072

 

  Index      Nissan     Nissan Rogue (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1070  1071  1072  1073   ..

 

 

Nissan Rogue. Manual - part 1072

 

 

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

SEC-67

< BASIC INSPECTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

NOTE:

If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after

replacing BCM.

>> GO TO 2.

2.

REPLACE BCM

Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT Configuration

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write

vehicle specification. Refer to 

BCS-121, "CONFIGURATION (BCM) : Work Procedure"

.

>> GO TO 4.

4.

INITIALIZE BCM (NATS)

Perform BCM initialization. (NATS) Refer to the CONSULT Immobilizer mode and follow the on-screen instruc-

tions.

>> Inspection End.

2015 Rogue NAM

SEC-68

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1610 LOCK MODE

DTC/CIRCUIT DIAGNOSIS

P1610 LOCK MODE

Description

INFOID:0000000011278461

ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times

or more while communication between ECM and BCM is not normal.

DTC Logic

INFOID:0000000011278462

DTC DETECTION LOGIC

NOTE:

• If DTC B1610 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC B1610 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” of “ENGINE” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-68, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278463

1.

CHECK ENGINE START FUNCTION

1. Check that there are no DTC’s except for DTC P1610 detected.

If detected, erase the DTC after fixing.

2. Turn ignition switch OFF.

3. Contact the registered Intelligent Key backside to push-button ignition switch and wait 5 seconds.

4. Turn ignition switch ON.

5. Turn ignition switch OFF and wait 5 seconds.

6. Repeat steps 3 and 5 twice (a total of 3 times).

7. Check that engine can start.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1610

LOCK MODE

When ECM detects a communication malfunction between 
ECM and BCM 5 times or more.

2015 Rogue NAM

P1611 ID DISCORD, IMMU-ECM

SEC-69

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

P1611 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000011278464

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” of “ENGINE” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-69, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278465

1.

PERFORM INITIALIZATION

Perform initialization of BCM and reregistration of all Intelligent Keys using CONSULT. Refer to the CONSULT

Immobilizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with reregistered Intelligent Key?

YES

>> Inspection End.

NO

>> GO TO 2.

2.

CHECK SELF DIAGNOSTIC RESULT

1. Select “Self Diagnostic Result” of “ENGINE” using CONSULT.

2. Erase DTC.

3. Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to 

SEC-69, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 3.

NO

>> Inspection End.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-

SULT Immobilizer mode and follow the on-screen instructions.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> Inspection End.

NO

>> GO TO 4.

4.

REPLACE ECM

1. Replace ECM. Refer to 

EC-502, "Removal and Installation"

.

2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”. Refer to 

EC-139, "Work Procedure"

.

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1611

ID DISCORD, IMMU-ECM

The ID verification results between BCM 
and ECM are NG.

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• BCM
• ECM

2015 Rogue NAM

SEC-70

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1612 CHAIN OF ECM-IMMU

P1612 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000011278466

DTC DETECTION LOGIC

NOTE:

• If DTC P1612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC P1612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON.

2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-70, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278467

NOTE:

• If DTC P1612 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC P1612 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

1.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT.

Check BCM power supply and ground circuit. Refer to 

BCS-68, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the harness.

2.

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT.

Check ECM power supply and ground circuit. Refer to 

EC-168, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the harness.

3.

PERFORM DTC CONFIRMATION PROCEDURE.

Perform the DTC confirmation procedure. Refer to 

SEC-70, "DTC Logic"

.

Does the DTC return?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

NO

>> Inspection End.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1612

CHAIN OF BCM-ECM

Inactive communication between BCM 
and ECM

• Harness or connectors

(The CAN communication line is open or 
shorted.)

• ECM 
• BCM

2015 Rogue NAM

 

 

 

 

 

 

 

Content   ..  1070  1071  1072  1073   ..