Nissan Altima HL32 Hybrid. Manual - part 914

PRE-INSPECTION FOR DIAGNOSTIC

PWC-97

< ON-VEHICLE MAINTENANCE >

[LH ONLY WINDOW ANTI-PINCH]

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

ON-VEHICLE MAINTENANCE

PRE-INSPECTION FOR DIAGNOSTIC

Basic Inspection

INFOID:0000000004215868

BASIC INSPECTION

1.

INSPECTION START

1. Check the service history.

2. Check the following parts.

• Fuse/circuit breaker blown.

• Poor connection, open or short circuit of harness connector.

• Battery voltage.
Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace the malfunctioning parts.

PWC-98

< ON-VEHICLE REPAIR >

[LH ONLY WINDOW ANTI-PINCH]

POWER WINDOW MAIN SWITCH

ON-VEHICLE REPAIR

POWER WINDOW MAIN SWITCH

Removal and Installation

INFOID:0000000004215869

REMOVAL

1. Remove the power window main switch finisher (2). Refer to

INT-14, "Removal and Installation"

.

2. Power window main switch (1) is removed from power window

main switch finisher (2) using a suitable tool (A). 

CAUTION:

Do not fold the pawl of power window main switch finisher.

NOTE:

The same procedure is also performed for front power window and

door lock/unlock switch RH, and rear power window switch (LH &

RH).

INSTALLATION

Installation is in the reverse order of removal.

: Pawl

JMKIA0150ZZ

DIAGNOSIS AND REPAIR WORKFLOW

PWC-99

< BASIC INSPECTION >

[LH&RH FRONT WINDOW ANTI-PINCH]

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORKFLOW

Work Flow

INFOID:0000000004215870

OVERALL SEQUENCE

JPLIA0089GB

PWC-100

< BASIC INSPECTION >

[LH&RH FRONT WINDOW ANTI-PINCH]

DIAGNOSIS AND REPAIR WORKFLOW

DETAILED FLOW

1.

 INTERVIEW FOR MALFUNCTION

Interview the symptom to the customer.

>> GO TO 2

2.

 SYMPTOM CHECK

Check the symptom from the customer's information.

>> GO TO 3

3.

 BASIC INSPECTION

Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.

>> GO TO 4

4.

 SELF-DIAGNOSIS WITH CONSULT-III

Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?

YES

>> GO TO 5

NO

>> GO TO 6

5.

 TROUBLE DIAGNOSIS BY DTC

Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.

>> GO TO 9

6.

 FAIL-SAFE ACTIVATION CHECK

Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?

YES

>> GO TO 7

NO

>> GO TO 8

7.

 SYSTEM DIAGNOSIS

Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.

>> GO TO 9

8.

 SYMPTOM DIAGNOSIS

Perform the symptom diagnosis. Specify the malfunctioning part.

>> GO TO 9

9.

 MALFUNCTION PART REPAIR

Repair or replace the malfunctioning part.

>> GO TO 10

10.

 REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)

Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is

detected before the repair. Check that DTC is not detected again.
Is any DTC detected?

YES

>> GO TO 5