Nissan Altima HL32 Hybrid. Manual - part 812

MWI

DIAGNOSIS SYSTEM (METER)

MWI-35

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DIAGNOSIS SYSTEM (METER)

Diagnosis Description

INFOID:0000000004219274

SELF-DIAGNOSIS MODE

• Odo/trip meter and information display segment operation can be checked in self-diagnosis mode.

• Meters/gauges can be checked in self-diagnosis mode.

OPERATION PROCEDURE

1. Turn the ignition switch OFF.
2. While pushing the odo/trip meter switch, turn the ignition switch ON again.
3. Push the odo/trip meter switch at least 3 times within 7 seconds after the ignition switch is turned ON.
4. The unified meter control unit is turned to self-diagnosis mode.

• All the segments on the odo/trip meter illuminate.

• Dots in all segments of information display LCD (1) flash alter-

nately.

NOTE:

If any of the segments are not displayed, replace the combina-

tion meter. Refer to 

MWI-135, "Removal and Installation"

.

5. Push the odo/trip meter switch. Each meter/gauge should indicate as shown in the figure.

CONSULT-III Function (METER/M&A)

INFOID:0000000004219275

CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.

SKIB1206J

JSNIA0020GB

AWNIA0072GB

MWI-36

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (METER)

SELF-DIAG RESULTS

Display Item List

Refer to 

MWI-72, "DTC Index"

.

DATA MONITOR

Display Item List

X: Applicable

METER/M&A diagnosis mode

Description

SELF-DIAG RESULTS

Displays combination meter self-diagnosis results.

DATA MONITOR

Displays combination meter input/output data in real time.

CAN DIAG SUPPORT MNTR

The result of transmit/receive diagnosis of CAN communication can be read.

Display item [Unit]

MAIN

SIGNALS

SELECTION 

FROM MENU

Description

SPEED METER [km/h] or [mph]

X

X

Displays the value of vehicle speed signal.

SPEED OUTPUT [km/h] or [mph]

X

X

Displays the value of vehicle speed signal, which is transmitted to 
each unit with CAN communication.

ODO OUTPUT

X

Displays the value, which is calculated by vehicle speed signal.

FUEL METER [lit.]

X

X

Displays the value, which processes a resistance signal from fuel 
gauge.

ABS W/L [ON/OFF]

X

Displays [ON/OFF] condition of ABS warning lamp.

VDC/TCS IND [ON/OFF]

X

Displays [ON/OFF] condition of VDC/TCS OFF indicator lamp.

SLIP IND [ON/OFF]

X

Displays [ON/OFF] condition of SLIP indicator lamp.

HEV BRAKE W/L [ON/OFF]

X

Displays [ON/OFF] condition of HEV brake warning lamp.*

DOOR W/L [ON/OFF]

X

Displays [ON/OFF] condition of door warning lamp.

TRUNK/GLAS-H [ON/OFF]

X

Displays [ON/OFF] condition of trunk warning lamp.

HI-BEAM IND [ON/OFF]

X

Displays [ON/OFF] condition of high beam indicator.

TURN IND [ON/OFF]

X

Displays [ON/OFF] condition of turn indicator.

OIL W/L [ON/OFF]

X

Displays [ON/OFF] condition of oil pressure warning lamp.

MIL [ON/OFF] 

X

Displays [ON/OFF] condition of malfunction indicator lamp.

CRUISE IND [ON/OFF]

X

Displays [ON/OFF] condition of CRUISE indicator.

SET IND [ON/OFF]

X

Displays [ON/OFF] condition of SET indicator.

FUEL W/L [ON/OFF]

X

Displays [ON/OFF] condition of low-fuel warning lamp.

WASHER W/L [ON/OFF]

X

Displays [ON/OFF] condition of low-washer fluid warning lamp.

AIR PRES W/L [ON/OFF]

X

Displays [ON/OFF] condition of tire pressure warning lamp.

KEY G W/L [ON/OFF]

X

Displays [ON/OFF] condition of key warning lamp.

PUSH ENG IND

X

Displays the value of Intelligent Key system message indication.

SHIFT IND [P, R, N, D, L]

X

Displays [P, R, N, D, L] range position of ECVT.

PKB SW [ON/OFF]

X

Displays [ON/OFF] condition of parking brake switch.

BUCKLE SW [ON/OFF]

X

Displays [ON/OFF] condition of seat belt buckle switch LH.

DISTANCE [km] or [mile]

X

Displays the value, which is calculated by vehicle speed signal, fuel 
gauge and fuel consumption from ECM.

OUTSIDE TEMP [

°C]

X

Displays the ambient air temperature, which is input from ambient 
sensor.

FUEL LOW SIG [ON/FF]

X

Displays [ON/OFF] condition of low-fuel warning signal.

BUZZER [ON/OFF]

X

X

Displays [ON/OFF] condition of buzzer.

ALL POWER METER [kw]

X

Displays the value of power meter.

SOC METER [%]

X

Displays the position of the high voltage battery status meter pointer.

MWI

DIAGNOSIS SYSTEM (METER)

MWI-37

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

NOTE:
Some items are not available due to vehicle specification.

EPS W/L [ON/OFF]

X

Displays [ON/OFF] condition of EPS warning lamp.

READY IND [ON/OFF]

X

Displays [ON/OFF] condition of READY indicator.

SYS FAIL W/L [ON/OFF]

X

Displays [ON/OFF] condition of hybrid system warning lamp.

SFT POSI W/L [ON/OFF]

X

Displays [ON/OFF] condition of shift position indicator.

HV BAT W/L [ON/OFF]

X

Displays [ON/OFF] condition of high voltage battery warning lamp.

CHAGE W/L [ON/OFF]

X

Displays [ON/OFF] condition of charge warning lamp.

LCD

X

Displays the value of Intelligent Key system message indication.

BRAKE OIL SW [ON/OFF]

X

Displays [ON/OFF] condition of brake fluid level switch.

Display item [Unit]

MAIN

SIGNALS

SELECTION 

FROM MENU

Description

MWI-38

< COMPONENT DIAGNOSIS >

DTC U1000 CAN COMMUNICATION

COMPONENT DIAGNOSIS

DTC U1000 CAN COMMUNICATION

DTC Logic

INFOID:0000000004219276

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000004219277

Symptom: Displays “CAN COMM CIRC [U1000]” as a self-diagnosis result of combination meter.

1.

CHECK CAN COMMUNICATION

Select “SELF-DIAG RESULTS” mode for “METER/M&A” with CONSULT-III.

>> Go to “LAN system”. Refer to 

LAN-16, "Trouble Diagnosis Flow Chart"

.

DTC

CONSULT-III display

Detection condition

U1000

CAN COMM CIRC 
[U1000]

When combination meter is not transmitting or receiving CAN communication signals for 2 
seconds or more.