Nissan Altima HL32 Hybrid. Manual - part 623

P0A78-128

HBC-241

< COMPONENT DIAGNOSIS >

D

E

F

G

H

I

J

K

L

M

A

B

HBC

N

O

P

NG

>> Connect securely.

13.

CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR

RESOLVER) 

See 

HBC-164, "Diagnosis Procedure"

.

OK or NG

OK

>> Replace hybrid transaxle (See 

TM-36, "Removal and Installation"

).

NG

>> Repair or replace harness or connector.

14.

CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

See 

HBC-171, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 15.

NG

>> Connect securely.

15.

CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RE-

SOLVER)

See 

HBC-171, "Diagnosis Procedure"

.

OK or NG

OK

>> Replace hybrid transaxle (See 

TM-36, "Removal and Installation"

).

NG

>> Repair or replace harness or connector.

HBC-242

< COMPONENT DIAGNOSIS >

P0A78-266, P0A78-267

P0A78-266, P0A78-267

Description

INFOID:0000000004211915

The inverter converts high-voltage direct current from the HV battery and alternating current for MG2 and

MG1. The inverter contains a three-phase bridge circuit, which consists of six power transistors each for MG2

and MG1, that converts direct current to three-phase alternating current. The MG ECU controls the actuation

of the power transistors. The inverter transmits information that is necessary for effecting control, such as the

amperage and voltage, to the MG ECU.

The MG ECU uses a voltage sensor, which is built into the inverter, to detect boosted high voltage to allow

control of the voltage boost.

The inverter voltage sensor outputs voltage that varies between 0 and 5 V in accordance with the changes in

the high voltage. The higher the high voltage, the higher the output voltage, and the lower the high voltage, the

lower the output voltage.

P0A78-266, P0A78-267

HBC-243

< COMPONENT DIAGNOSIS >

D

E

F

G

H

I

J

K

L

M

A

B

HBC

N

O

P

The MG ECU monitors the inverter voltage and detects malfunctions.

DTC Logic

INFOID:0000000004211916

DTC DETECTION LOGIC

The MG ECU monitors the inverter voltage (VH) sensor circuit. If the MG ECU detects an open or short in the

VH sensor circuit, the hybrid vehicle control ECU will illuminate the MIL and set a DTC.

JMCIA0099GB

DTC No.

INF Code

Trouble diagnosis name

DTC detecting condition

Possible cause

P0A78

266

Drive Motor “A” Inverter 
Performance

Open or short to GND in the inverter 
voltage (VH) signal line

Inverter with converter assembly

267

Short to +B in the inverter voltage (VH) 
signal line

HBC-244

< COMPONENT DIAGNOSIS >

P0A78-266, P0A78-267

Diagnosis Procedure

INFOID:0000000004211917

1.

PRECONDITIONING

• Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with

converter assembly, take safety precautions such as wearing insulated gloves and removing the service

plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent

other technicians from accidentally reconnecting it while you are working on the high-voltage system.

• After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage

connectors or terminals.

• Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with

converter assembly.

>> GO TO 2.

2.

REPLACE INVERTER WITH CONVERTER ASSEMBLY

Refer to 

HBC-638, "Removal and Installation"

.

>> COMPLETED